PEERLESS Smartmount SA752PU Guide

Models: SA752PU, SA752PU-S

Installation and Assembly:

Universal Articulating Arm Wall Mount for 32" to 52" Plasma

and LCD Screens

Maximum UL Load Capacity: 90 lb (41 kg)

USC

ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

3215 W. NorthAve. • Melrose Park, IL • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

2 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.............................................................................................................................................................................3, 4

Wall installation...................................................................................................................................................................5, 6

Installing Adapter Brackets to Screen................................................................................................................................8-10

Mounting Flat Panel Screen.................................................................................................................................................11

Cable Management..............................................................................................................................................................13

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• 5/32" (4 mm) drill bit for wood studs

• 5/16" (8 mm) drill bit for concrete and cinder block

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Metal Stud Contact Qualiﬁed Professional (not evaluated by UL)

• Brick Contact Qualiﬁed Professional (not evaluated by UL)

• Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

CDE FG

SA752PU SA752PU-

Description Qty. Part # Part #

wall arm assembly 1 095-P1642 095-4642

Buniversal adapter bracket 1 095-P1635-2 095-4635-2

Cwood screws 3 520-1202 520-2165

Dconcrete anchors 3 590-0320 590-0320

EM10 x 5 mm socket head screw 2520-9262 520-9534

Ffastener caps 3590-1324 590-4324

Gcable ties 8590-1168 590-1168

H6 mm allen wrench 1 560-9716 560-9716

I5 mm allen wrench 1 560-9640 560-9640

Jrear cable cover 2 590-P1326 590-4326

Kfront cable cover 2 590-P1327 590-4327

L#3 screwdriver bit (not shown) 1 560-0209 560-0209

Parts List

4 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

Adapter Bracket Fasteners

M4 x 12 mm (6)

(504-9013)

M4 x 25 mm (4)

(504-1015)

M5 x 12 mm (4)

(520-1027) M5 x 25 mm (4)

(520-9543)

M8 x 16 mm (6)

(520-9257) M8 x 40 mm (4)

(520-1136)

M8 x 25 mm (4)

(520-1031) I.D. .34" (4)

(540-1059)

M10 x 15 mm (4)

(520-9262) BLK

(520-9534) SLV

I.D. .22" (4)

(540-1057)

M6 x 30 mm (4)

(510-9109)

M6 x 12 mm (4)

(520-1128) M6 x 25 mm (4)

(520-1208)

M6 x 20 mm (4)

(520-9402)

multi-washer (6)

(580-1036)

M4 x 20 mm (4)

(504-9020) BLK

(504-2020) SLV

M4 x 30 mm (4)

(520-1133) BLK

(520-2133) SLV

M6 x 20 mm (4)

(520-9402) BLK

(520-2402) SLV

M6 x 30 mm (4)

(510-9109) BLK

(510-2109) SLV

M6 x 40 mm (4)

(520-1584) BLK

(520-1207) SLV

ID.128" (4)

(590-5005) BLK

(590-5003) SLV

5 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

Using a stud ﬁnder, locate and mark the edges of the wood stud. Use of an edge to edge stud ﬁnder is highly

recommended. Use a level to draw a vertical line down the center of the stud and use wall plate (A) as template to

mark center of holes along the vertical line. The top mounting holes should be 7.54" (192 mm) above the desired

screen center as shown in ﬁgure 1.1. Drill three 5/32" (4 mm) dia. holes to a depth of 2.5" (64 mm). Attach wall arm

(A) to wall with three wood screws (C) using #3 phillips screwdriver bit (L) as shown in ﬁg. 1.2. Level plate, then

tighten all fasteners.

Insert three fastener caps (F) into wall plate mounting holes.

Installation to Single Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

7.54"

(192 mm)

CS = CENTER OF SCREEN

WOOD STUD

WALL PLATE

ﬁg. 1.1

ﬁg. 1.2

6 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

Installation to Solid Concrete or Cinder Block

Use wall arm (A) as template to mark mounting holes.

The top mounting hole should be 7.54" (192 mm) above

the desired screen center as shown in ﬁgure 1.1 on

page 5. Drill three 5/16" (8 mm) dia. holes 2.5" (64 mm)

deep as shown in ﬁg. 1.3. Insert anchors (D) into holes

ﬂush with wall as shown. Place wall arm over anchors

and secure with three wood screws (C) using #3

screwdriver bit (L). Level, then tighten all fasteners.

Insert three fastener caps (F) into wall plate mounting

holes.

ﬁg. 1.3

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16 mm), custom fasteners must be supplied

by installer (not evaluated by UL).

WARNING

SOLID CONCRETE CINDER BLOCK

WALL PLATE

7 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

NOTE: For dedicated PLP plate skip to step 3 on page 9.

Remove four 1/4-20 x .6" screws using 5 mm allen wrench (I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to

allow for screen bracket adjustment.

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen.

Place screen face side down and refer to screen manufacturers instructions for removal obstructions from the

back of the screen to prepare for mounting screen brackets to screen. Adjust screen brackets to align with screen

mounting holes as shown below. Select the small, medium, large or extra large screws from the bafﬂed fastener

pack, then attach screen brackets to screen following step 2-1 or 2-2 on page 8.

NOTE: Top and bottom mounting holes must be used for attaching screen brackets. Middle holes should also be

used where the fasteners and screens allow. Verify that all holes are properly aligned, then tighten screws using a

phillips screw driver.

CENTER SCREEN BRACKETS VERTICALLY ON BACK OF SCREEN

SCREEN

SCREEN BRACKETS

SCREEN

BRACKETS

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

• Tighten screws so screen brackets are ﬁrmly attached to screen. Do not tighten with excessive force. Overtightening

can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to

become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

1/4-20 x 1.25" SCREW

1/4-20 x .6" SCREW

SLIDE

BLOCK

Reinstall four 1/4-20 x .6" screws using 5 mm allen wrench (I) into appropriate ﬁxed-stop position located between screen

bracket and slide block as shown in detail 1. Fully tighten two 1/4-20 x 1.25" screws.

DETAIL 1

TOP VIEW

STOP-POSITION #1

STOP-POSITION #2

STOP-POSITION #3

8 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

Begin with the shortest length screw, hand thread screw through multi-washer and screen brackets (B) into screen

as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not

over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed

fastener pack. Repeat for remaining mounting holes, level screen brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

Begin with longer length screw, hand thread screw through multi-washer, screen brackets (B) and spacer in that

order into screen as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug

into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw

from the bafﬂed fastener pack. Repeat for remaining mounting holes, level screen brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

2-1

2-2

SCREEN

MULTI-WASHER

SCREW

SCREEN MULTI-WASHER

SCREW

SPACER

If you have any questions, please call Peerless customer care at 1-800-865-2112.

9 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

For Dedicated PLP Plate (not evaluated by UL):

Refer to PLP model instruction sheet for attachment

of dedicated PLP plate to screen.

Install two M10 x 15 mm screws (provided with

dedicated PLP plate) into top two holes of dedicated

PLP plate leaving 1/4" of exposed thread as shown

in ﬁgure 3.1.

Insert two M10 x 15 mm screws (E) into bottom holes of adapter plate as shown in ﬁgure 3.3 or 3.4. Tighten all

fasteners with 6 mm allen wrench (H).

3-1

ADAPTER PLATE

SCREEN NOT

SHOWN FOR

CLARITY

• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely

handle placement of the screen.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten M10 x 15 mm

screws (E) to 40 in. • lb (4.52 N.M.) maximum torque.

WARNING

Mounting Flat Panel Screen

1/4"

M10 X 15 MM SCREW

1/4"

M10 X 15 MM SCREW

DEDICATED PLP PLATE

ADAPTER PLATE

ﬁg. 3.1

ﬁg. 3.2

DEDICATED PLP PLATE

ADAPTER PLATE

ﬁg. 3.4ﬁg. 3.3

For Universal Adapter Bracket: Hook M10 x 15 mm

screws into keyslots of wall arm adapter plate (A) as

shown ﬁgure 3.2.

10 of 46 ISSUED: 10-30-09 SHEET #: 095-9297-2 12-04-09

FOR PORTRAIT OR LANDSCAPE SCREEN ORIENTATION: Remove two M5 x 12 mm screws and rotation block

from top of tilt head as shown in top view and rear view. Gently grasp sides of screen and rotate screen into portrait

or landscape position as shown in ﬁgure 4.1 and reinstall rotation block with two M5 x 12 screws.

TILT Adjustment: Adjust tension knob on side of

mount to desired tension to enable tilt adjustment and

balance your screen size and weight. Push or pull

from top or bottom of screen to adjust tilt as shown.

The tilt can be adjusted to a maximum of 10° forward

or 5° backward. Retighten tension knob.

ROLL Adjustment: Rotate screen 5° clockwise or

counter-clockwise, level screen then tighten

M5 x 10 mm screws using 5 mm allen wrench (I) as

shown in detail 2.

FOR VERTICAL HEIGHT ADJUSTMENT: Tighten or

loosen two M8 x 40 mm screws an equal number of

turns to achieve ± 1" of vertical height adjustment as

shown in detail 2.

Adjustment of Flat Panel Screen

TENSION KNOB

DETAIL 2

ﬁg. 4.1

M5 X 10 MM

SCREWS

M8 X 40 MM

SCREWS

• Do not tighten screws with excessive force.

• Be careful not to pinch ﬁngers when opening and

closing mount from the wall.

CAUTION

M5 X 12 MM SCREWS

TOP VIEW

ROTATION BLOCK

REAR VIEW

M5 X 12 MM SCREWS

ROTATION BLOCK

• M10 x 15 mm screws (E) must be securly tightened before changing orientation of wall arm assembly (A). Failure to

lock adapter bracket can cause screen to come off of mount.

WARNING

Other manuals for Smartmount SA752PU

This manual suits for next models

Table of contents

Languages:

Other PEERLESS Rack & Stand manuals

PEERLESS

PEERLESS PANA-85WM Guide

PEERLESS

PEERLESS SF630P-S and assembly Guide

PEERLESS

PEERLESS HCACC502 User manual

PEERLESS

PEERLESS SmartMount SP740P Guide

PEERLESS

PEERLESS IB40 Guide

PEERLESS

PEERLESS SUT632P Guide

PEERLESS

PEERLESS WSP820 Guide

PEERLESS

PEERLESS ACC517 Guide

PEERLESS

PEERLESS MSA-301 Guide

PEERLESS

PEERLESS Vision-Point LCV 100 Guide

PEERLESS

PEERLESS WSP700 Instruction Manual

PEERLESS

PEERLESS Smartmount ST670 Guide

PEERLESS

PEERLESS LCT Series Guide

PEERLESS

PEERLESS WSP 716 User manual

PEERLESS

PEERLESS PLCM 3 Guide

PEERLESS

PEERLESS WSP700 Instruction Manual

PEERLESS

PEERLESS ACC605 Guide

PEERLESS

PEERLESS SmartMount SA750P Guide

PEERLESS

PEERLESS PARAMOUNT PA730 Guide

PEERLESS

PEERLESS Perfect Mount PMF2X2 User manual

PEERLESS

PEERLESS LWB375 Guide

PEERLESS

PEERLESS SmartMount SP740P Guide

PEERLESS

PEERLESS Paramount PF660 Guide

PEERLESS

PEERLESS Solid-Point PLB 1 Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 