PEERLESS PLA 50-UNL Guide

Models: PLA 50-UNL, PLA 50-UNL-S,

PLA 50-UNLP, PLA 50-UNLP-S,

RTPLA50-S

Installation and Assembly - Universal Articulating

SwivelArm for 32" - 50" Plasma Screens

Maximum Load Capacity::

:150 lb (68 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

2 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

Accessories

•concreteanchor4-pack(ACC210)

Read instruction sheet before you start installation and assembly.

Installations:

To Wood Stud Walls ...................................................................................................... page 6

To Concrete Walls .......................................................................................................... page 7

IMPORTANT! Turn to the appropriate page for your wall installation.

• Donotbegin to install your Peerless product until you have read andunderstoodthe instructions and warnings

containedinthis Installation Sheet. If you have any questions regarding any of the instructionsorwarnings,please

callPeerlesscustomercareat1-800-729-0307.

• Thisproductshouldonlybeinstalledbyaqualifiedprofessional.

• Makesure that the supporting surface will safelysupportthe combined load of the equipment andall attached hard-

wareandcomponents.

• NeverexceedtheMaximumLoadCapacityof150lb(68kg).

• Never mount this product to metal studs.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgetoedge"studfinderishighlyrecommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrewsandnutsfirmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheir

holdingpower.

WARNING

Tools Needed for Assembly

•studfinder ("edge to edge" stud finder isrecommended)

•drill

•3/16" drill bit for wood studs

•5/16" drill bit for concrete

•7/16"socket wrench with extension (recommended) for woodscrews

•10 mm socket wrench for concrete anchors

•level

•phillipsscrewdriver

WALLCONSTRUCTION ADDITIONAL HARDWARE REQUIRED

Wood Stud, Wood Beam none

Solid Concrete Contact Customer Care for accessory kit

Other or unsure? Contact Customer Care

IMPORTANT! Certain types of walls require additional mounting hardware...

3 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

MODEL MODEL

PLA50-UNL RTPLA50-S

PLA50-UNLP PLA50-UNL-S

PLA50-UNLP-S

DESCRIPTION QTY. PART# PART#

Awallplate 1 201-1095 201-4095

Btilt-roll assembly 1 201-1093 201-4093

Carmassembly 1 201-1094 201-4094

Dwallsupport arm axle 1 201-1041 201-1041

Evinyltrim 3 600-1012 600-1012

FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262

G.505 x .75 x .062" nylon washer 1 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315

J1.525 x 2 x .062" delrin washer 2 540-1070 540-1070

K#8-32 x .375" socket head cap screw 1 520-1210 520-1210

Lplastic finishing cap 8 590-1123 590-1123

Mholdingpin 1 580-1166 580-1166

Nretainerplug 1 590-1007 590-1007

O5/16 x 3" wood screw 6 520-1243 520-1243

P.250 x 1 x .068" washer 6 540-1063 540-1063

Q9/64"allenwrench 1 560-9728 560-9728

Rcablemanagementclips 4 590-1166 590-1166

Scable tie 4 590-1168 590-1168

T36"polyestermeshsleeve 1 600-1015 600-1015

U6 mm allen wrench 1 560-9716 560-9716

Before you start make sure all parts

listed are included with your product.

Wall Mount Parts List

Some parts may appear slightly different than illustrated.

S T

4 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

PLA 50-UNL PLA 50-UNL-S PLA 50-UNLP PLA 50-UNLP-S

Description Qty Part # Part # Part # Part #

AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110

BB shallow adapter bracket 2 200-0756 200-0757 200-0754 200-0755

CC deep adapter bracket 2 200-0752 200-0753 200-0750 200-0751

DD allen wrench 1 560-9646 560-9646 560-0072 560-0072

Before you begin, make sure all parts shown are included with your product.

Adapter Bracket Parts List

RTPLA50-S

5 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

M5 x 25 mm (4)

520-1122

M4 x 12 mm (6)

510-1079

M4 x 25 mm (4)

510-1082

M5 x 12 mm (4)

520-1064 M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211

I.D. 5.6 mm (4)

540-1057

multi-washer(6)

580-1036

I.D. 8.7 mm (4)

540-1059

SecurityAdapter Bracket Fasteners

M6 x 20 mm (4)

520-9554

M6 x 30 mm (4)

520-1067

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M8 x 25 mm (4)

520-1101

M6 x 20 mm (4)

520-9402

M6 x 30 mm (4)

510-9109 multi-washer(6)

580-1036

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M4 x 12 mm (6)

504-9013

Phillips Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027 M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208

I.D. 5.6 mm (4)

540-1057

M8 x 25 mm (4)

520-1031

I.D. 8.7 mm (4)

540-1059

6 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

• Installermustverifythatthesupportingsurface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

• Tightenwoodscrewssothatwallplateisfirmlyattached,butdonotovertighten.Overtighteningcandamagethe

screws,greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Never mount this product to metal studs.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers

areresponsible to provide hardware forothertypes of mounting situations.

• NeverexceedtheMaximumLoadCapacityof150lb(68kg).

WARNING

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useof an edge-to-edge stud finder is highlyrecommended. Based on their edges, draw avertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located 3.9" below the

desired screen center. Level plate, and mark the center of the four mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill six 3/16" (5 mm) dia. holes 3" (76 mm) deep. Make sure that the wall plate is

level, secure it using six 5/16 x 3" wood screws (O) and washers (P).

Skip to step 2 on page 8.

7 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

Make sure that wall plate (A) is level, use it as a tem-

plate to mark six mounting holes. The top mounting slots

should be located 3.9" below the desired screen center.

Drill six 5/16" (8 mm) dia. holes to a minimum depth of

1.75" (45 mm). Attach wall plate (A) using concrete

expansionanchors and washers (P) as shown in 1-1

through1-4. A

FORPRODUCT SAFETYUSEONLYRAWL™

#5005OR HILTI™HL814 CONCRETEANCHORS.

Order TWO #ACC 210 accessory kits, each contains

four .312 x 1.625 (8 mm x 41 mm) concrete expan-

sionanchors.

Align hole in wall plate (A) with hole in wall. Gently

hammerinconcreteanchor as shown.

Usea 10 mm wrench (not provided) to tighten concrete

anchor to 80 in • lb(9 N.M.) maximum torque as shown.

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansion anchors to concrete

coveredwith plaster, drywall, orotherfinishing mate-

rial.

WARNING

• Tightenconcreteanchorboltfirmly,but do not over-

tighten.Overtightening can damage the bolt, greatly

reducingits holdingpower.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

1-1

1-2

1-3 1-1

1-2

1-3

WARNING

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safelysupportthe combined load of the equipment andall attached hard-

wareand components.

• NeverexceedtheMaximumLoadCapacityof150lb(68kg).

Installation to Concrete Wall

Note: Fasteners for concrete walls are not included,

orderTWO #ACC 210accessory kitsfor installation

on concrete walls.

Concreteexpansion anchorsare not intendedfor

attachmenttoconcrete covered with a layer of plaster,

drywall,or other finishing material.

1-4

CUTAWAYVIEW

1-4

8 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown.Cable ties (S) are used with

clipsfor cord management.

Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.

Note: There are five mounting positions. The

center position is shown (right). Slidewasher(J)

over wall support arm axle (D). Next, insert plastic

cap (N) into axle. Then, insert holding pin (M) into

axle. See detail 1.

Note: Fit of axle (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

2-1

3-1

Insert socket cap screw (K) into hole at bottom of

wall support arm axle (D) as shown in detail 3.

Tightenscrew using 9/64" allen wrench (Q).

DETAIL 3

ADETAIL 1

Place arm assembly (C) with washer (J) into wall

plate (A). Insert axle assembly shown in detail 1

throughwallplate(A), arm assembly (C),and

washer (J). Lock axle in place by aligning holding

pin (M) with notches shown in detail 2.

2-2 NOTCH

DETAIL 2

• If you are uncertain that product is properly installed, call customer care.

WARNING

9 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).Attach tilt-roll assembly to adapter bracket

(AA) with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

• Donot overtightenscrews! Overtightening mayhinder

rolloption.

CAUTION

Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm

assembly(C).

4-1 Insertonefinishing cap (L) into each unused hole of wall plate (A).

SWIVELBOX

10 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.

Hook tilt-roll assembly (B) onto M10 screws (F).

Insert carriage bolt (I) into slot of swivel box as

shown in figure 6.1. Install nylon washer (G) and tilt

adjustmentknob (H).

Install remaining two M10 screws (F) as shown in

figure6.2. HAND TIGHTEN all fourM10screws to

allowfor tilt adjustment. Remove tapefromcarriage

bolt (I). For tilt adjustment, push back on the top of

plasma to relieve pressure on knob.Adjust tilt to

desired position and tighten tilt adjustment knob (H),

then securely tighten all four M10 screws (F) using 6

mmallen wrench (U).

.25"

• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.

WARNING

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

6-1

6-2

fig 6.1 fig 6.2

SWIVELBOX

SWIVELBOX C

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

This manual suits for next models

Table of contents

Other PEERLESS Rack & Stand manuals

PEERLESS

PEERLESS WSP 716 User manual

PEERLESS

PEERLESS LCC 18 Guide

PEERLESS

PEERLESS IWB600-WB User manual

PEERLESS

PEERLESS CMJ 470W Guide

PEERLESS

PEERLESS SA761PU Guide

PEERLESS

PEERLESS Smartmount SA752P Guide

PEERLESS

PEERLESS HL4UN-002 Guide

PEERLESS

PEERLESS FPZ-600 Guide

PEERLESS

PEERLESS A100IWBMOUNT Guide

PEERLESS

PEERLESS Solid-Point PLCM 1 CP Guide

PEERLESS

PEERLESS SP730P Guide

PEERLESS

PEERLESS SUF650P and assembly Guide

PEERLESS

PEERLESS DS-VW760 and assembly Guide

PEERLESS

PEERLESS SmartMount ST 635 Guide

PEERLESS

PEERLESS SF630P-S and assembly Guide

PEERLESS

PEERLESS A100IWBMOUNT Guide

PEERLESS

PEERLESS PLA 60-UNL Guide

PEERLESS

PEERLESS SmartMount D-FPF-320 Guide

PEERLESS

PEERLESS Vision Point LCFS 100 Guide

PEERLESS

PEERLESS WSP820 Guide

PEERLESS

PEERLESS LMAM1940 Guide

PEERLESS

PEERLESS PLT BLK Guide

PEERLESS

PEERLESS SmartMount D-FPF-320 Guide

PEERLESS

PEERLESS PARAMOUNT PF640 Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 