Keysight Technologies 8970B User manual

Keysight Technologies

8970B Noise Figure Meter

Security and

Memory Clearing

Notices

© Copyright 2018 Keysight Technologies, Inc.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

08970-90006

Edition

Edition 1, November 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

8970B Noise Figure Meter Security and Memory Clearing 3

8970B Noise Figure Meter Security and Memory Clearing

8970B Noise Figure Meter Security and Memory Clearing

Introduction

8970B memory clearing process requires removal of the processor battery for 15 minutes or longer.

Below are step-by-step instructions for removing this battery. Make sure you use proper ESD

pre-cautions.

Tools Required

— Torx T15 driver

— #2 Phillips screwdriver

Procedure

1. Unplug the 8970B from AC power.

2. Place the instrument upside-down on a flat surface.

3. Remove the bottom cover using Torx T15 driver and #2 Phillips screwdriver.

4. Lift the processor assembly by loosening the two screws and hinge the board away as shown

below:

Figure 1 Battery Location

4 8970B Noise Figure Meter Security and Memory Clearing

8970B Noise Figure Meter Security and Memory Clearing

5. Remove battery shown in the lower-left corner of the processor board. Lift the contact clip and

slide the battery out.

6. After 15 minutes, replace the battery with positive terminal out as shown on the clip.

7. Re-install the processor board and replace the instrument bottom cover.

8. Connect the AC power cord and turn on the instrument.

9. Instrument memory is cleared if error message E80 (lost battery) appears at turn-on.

10.It is NOT necessary to re-enter the ENR tables for noise sources at this point.

11.Connect a noise source to the BNC drive and the RF input (failure to do this will cause an E13

IF calibration failure message).

12.Invoke special function 33.1 to perform the I.F. calibration.

13.You may now calibrate the 8970B as desired for your next measurement.

Contacting Keysight

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

© Keysight Technologies 2018

Edition 1, November 2018

08970-90006

www.keysight.com

Table of contents

Other Keysight Technologies Measuring Instrument manuals

Keysight Technologies

Keysight Technologies Option 503 User manual

Keysight Technologies

Keysight Technologies N774 C Series User manual

Keysight Technologies

Keysight Technologies N9030B Installation and operation manual

Keysight Technologies

Keysight Technologies N9000B Installation and operation manual

Keysight Technologies

Keysight Technologies U1084A User guide

Keysight Technologies

Keysight Technologies N432A User manual

Keysight Technologies

Keysight Technologies 34980A User manual

Keysight Technologies

Keysight Technologies N77 Series User manual

Keysight Technologies

Keysight Technologies E4980A Quick start guide

Keysight Technologies

Keysight Technologies EXA N9010A User manual

Keysight Technologies

Keysight Technologies N8480 Series Service manual

Keysight Technologies

Keysight Technologies M9393A User guide

Keysight Technologies

Keysight Technologies N7373C Manual

Keysight Technologies

Keysight Technologies CX3300 Series User manual

Keysight Technologies

Keysight Technologies E5260 Series Operating instructions

Keysight Technologies

Keysight Technologies M9393A User manual

Keysight Technologies

Keysight Technologies CXA Installation and operation manual

Keysight Technologies

Keysight Technologies E5055A SSA-X User manual

Keysight Technologies

Keysight Technologies N5241BU-677 User manual

Keysight Technologies

Keysight Technologies N9020B Installation and operation manual

Keysight Technologies

Keysight Technologies E4981A Owner's manual

Keysight Technologies

Keysight Technologies N9030B Installation and operation manual

Keysight Technologies

Keysight Technologies S9106AC-2IF User guide

Keysight Technologies

Keysight Technologies MXA N9020A-508 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual