Keysight Technologies CXA Installation and operation manual
Option PRC - Portable Configuration
Keysight CXA/EXA/MXA Signal Analyzer
Installation Note
Notices
© Copyright 2009-2015 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9020-90133
Supersedes N9020-90044
Edition
Edition 1, April 2015
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9020-90133 3
Option PRC, Portable Configuration Installation Kit
Option PRC,
Portable Configuration Installation Kit
Introduction
This installation note is part of a retrofit kit that enables the installation of Option PRC, Portable
Configuration. This retrofit kit provides the bumpers and handle hardware needed to convert a
bench top signal analyzer into a portable signal analyzer.
CAUTION While the parts in this upgrade kit could also be installed onto a PXA N9030A
signal analyzer, this kit is NOT to be used with these instruments.
The bail handle for the portable configuration, and its attachment to the
instrument, has NOT been designed to support the added weight of the PXA
N9030A signal analyzer.
The use of this portable configuration upgrade kit with a PXA N9030A signal
analyzer, or any other unintended use, could result in either personal injury or
instrument damage.
Products Affected: CXA N9000A
EXA N9010A
MXA N9020A
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
(X) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time: 0.5 Hours
N/A
4Installation Note N9020-90133
Option PRC, Portable Configuration Installation Kit
Contents
Tools Required
— T-20 Torx driver
—Smallflatheadscrewdriver
Quantity Description Keysight Part
Number
1 Installation Note This note
1 Trim Strip, Top with Bumper W1312-40004
4 Bumper Assembly, Front W1312-40020
4 Bumper Assembly, Rear W1312-40021
4 Hole Plug, Strap Handle W1312-40024
1 Cover, Impact W1312-40025
4 Hole Plug, Bottom Foot W1312-40032
1 Bail Handle Assembly W1312-60036
12 Screw M4 X 0.7 14 mm-LG 0515-0435
4 Screw M5 X 0.8 14 mm-LG 0515-5209
4 Screw M4 X 0.7 25 mm-LG Pan head 0515-1619
4 Washer, Flat 3050-0893
Installation Note N9020-90133 5
Installation Procedure
Installation Procedure
1. Refer to Figure 1. Locate and remove both strap handle assemblies (1) (N9020-60002). Each
handle is attached to the instrument case with two Torx 20 screws. Set aside the two strap
handle assemblies as they are no longer needed.
Figure 1 Strap Handle Removal
2. Locate four strap handle hole plugs (W1312-40024) and four screws (0515-5209) from the kit.
Install strap handle hole plugs and secure with screws. Torque to 21 in-lbs.
3. Locate and remove the four key locks (5021-2840) from the four instrument feet located on the
bottom of the instrument. Set aside the four key locks as they are no longer needed.
4. Locate and remove the four instrument feet (2) (5041-9167) located on the bottom of the
instrument. Set aside the four instrument feet as they are no longer needed.
5. Locate and remove the four rear feet (3) (5041-9611). Each foot is attached with one Torx 20
screw and a washer. Set aside the four rear feet, the four screws and the four washers as they
are no longer needed.
6Installation Note N9020-90133
Installation Procedure
NOTE 1. It is recommended that all of the parts that have just been removed be
stored away somewhere together in case you need to return the instrument to
the bench top configuration.
2. The screws attaching the four rear bumpers are what hold the instrument
cover in place. Once these have been removed, be careful not to disturb the
instrument cover placement as it is seated into the EMI gasketing in the front
frame. Also, removal or excessive movement of the instrument cover may
break any calibration or security seals that may have been placed on the
instrument.
6. Refer to Figure 2. Locate four rear bumper feet (1) (W1312-40021), four screws (0515-1619)
and four washers (3050-0893) from the kit. Install the rear bumper feet. Secure with screws
and washers. Torque to 21 in-lbs.
Figure 2 Rear Bumper Installation
7. Locate and install four foot hole plugs (2) (W1312-40032) from the kit.
Installation Note N9020-90133 7
Installation Procedure
8. Refer to Figure 3. Locate the top trim strip on the front panel. The top trim strip snaps into
place. Use a small flathead screw driver to remove the top trim strip as shown. Ensurethat you
do not scratch the front panel. Discard the top trim strip.
Figure 3 Top Trim Strip Removal
9. Refer to Figure 4. Locate and remove the adhesive side trim strips from both sides of the front
panel. Discard the side trim strips.
8Installation Note N9020-90133
Installation Procedure
Figure 4 Side Trim Strip Removal
10.Locate the top trim strip (W1312-40004) from the kit. Snap top trim strip into place in the
cavity on the top of the front frame.
11.Refer to Figure 5. Locate four front bumpers (1) (W1312-40020) and eight screws
(0515-0435) from the kit. Install front bumpers with long side facing forward. Secure each
front bumper with two screws. Torque to 21 in-lbs.
Installation Note N9020-90133 9
Installation Procedure
Figure 5 Front Bumper Installation
10 Installation Note N9020-90133
Installation Procedure
12.Refer to Figure 6. Locate Bail Handle assembly (1) (W1312-60036) and four screws
(0515-0435) from the kit. Adjust handle as shown. Snap handle into place on the instrument
front frame. Secure the Bail Handle assembly with screws. Torque to 21 in-lbs.
Figure 6 Bail Handle Installation
13.Locate Impact Cover (W1312-40025). This cover is used to protect the instrument front panel
during transport. Since it must be removed to use the instrument, you may or may not put it on
the instrument at this time depending on your need.
This manual suits for next models
2
Table of contents
Other Keysight Technologies Measuring Instrument manuals
Keysight Technologies
Keysight Technologies MXA N9020A Installation and operation manual
Keysight Technologies
Keysight Technologies PNA-X N5241A User manual
Keysight Technologies
Keysight Technologies M981 AS Series User manual
Keysight Technologies
Keysight Technologies N2750A User manual
Keysight Technologies
Keysight Technologies N9030A Installation and operation manual
Keysight Technologies
Keysight Technologies PXA N9030A Installation and operation manual
Keysight Technologies
Keysight Technologies N5224/5A User manual
Keysight Technologies
Keysight Technologies B1500A Instruction Manual
Keysight Technologies
Keysight Technologies N432A User manual
Keysight Technologies
Keysight Technologies P50 B Series User manual
Keysight Technologies
Keysight Technologies U1281A User manual
Keysight Technologies
Keysight Technologies X Series User manual
Keysight Technologies
Keysight Technologies EXA N9010B Installation and operation manual
Keysight Technologies
Keysight Technologies ENA Series Quick start guide
Keysight Technologies
Keysight Technologies B2981A Installation guide
Keysight Technologies
Keysight Technologies PNA-L N5230A User manual
Keysight Technologies
Keysight Technologies UXA N9040B Installation and operation manual
Keysight Technologies
Keysight Technologies N77 Series User manual
Keysight Technologies
Keysight Technologies U4164A User manual
Keysight Technologies
Keysight Technologies N5511A-K26 User manual
