General A3G User manual
INSTRUCTION MANUAL
A3G Green Rotary Laser
2
Please read this instruction manual before operating this product.
Please store this instruction manual in the carry case for future reference.
CAUTION: Class 3 Laser Product
Do not stare directly into the laser beam from apertures.
Do not disassemble the instrument or attempt to perform any internal servicing
as this will void your warranty. No user serviceable parts included.
Only approved and authorised service technicians can carry out warranty repairs.
SAFETY
3
Please ensure the following items are included with your laser.
If anything is missing please contact your retailer.
ITEM CHECKLIST
Laser glasses Carry case Rechargeable
battery pack
Charger
2x Laser targetsDetector and clampRemote control
General A3G
INCHES CM
1
1
2
3
4
5
6
7
2
3
90°
SLEEP
45°
10°
180°
4
Rotating laser port
Protective lighthouse
PRODUCT OVERVIEW
Control panel
5
90°
45°
10°
180°
CONTROL PANEL
Power
Tilt alarm indicator
Power indicator
Speed control
Counter clockwise rotation
Tilt alarm
Clockwise rotation
Scanning mode
Speed control indicator
6
DETECTOR CONTROL PANEL
Sound on / off
Coarse / fine mode
LCD display screen
Laser sensor
Speaker
Power
7
REMOTE CONTROL PANEL
Sleep mode
90°
SLEEP
45°
10°
180°
Counter clockwise rotation
Scanning mode
Clockwise rotation
Speed control
8
USING YOUR LASER
Power Supply
‣The General A3G is supplied with a rechargeable Ni-MH battery pack that is
located in the base of the unit.
‣It is recommended that the battery pack be completely charged before use.
‣Charging time is approximately 5 hours.
‣Use of the unit over time and changes in temperature may cause increases
or decreases in charging and operation time.
‣The power indicator light will flash when the battery is low. The unit should
be re-charged as soon as possible.
‣To charge the unit insert the charger into the port on the battery pack.
Progress will be shown by the power indicator display on the charger as below:
Red (flashing) = Charger and battery are not connected.
Red (constant) = Battery is charging.
Green (constant) = Battery is charged.
9
Horizontal Set Up
Vertical Set Up
‣Select a place as close as practical to the work site.
Ensure the location is clear of traffic.
‣Attach the laser to a tripod and place on a level surface.
Ensure the unit is secured correctly and tightened in position.
‣Select a place as close as practical to the work site.
Ensure the location is clear of traffic.
‣Place the laser onto a level surface with the control panel facing upwards.
10
Operation
‣To turn the unit on press the power button. Self
levelling will commence and the laser will begin to rotate.
‣If the unit is outside the self levelling range the unit will not
level causing the laser beam to flash continuously.
Speed Control
‣Press the speed control button to cycle through various rotational speeds.
‣The speed control indicator will flash slowly when speed is slow and fast
when speed is increased.
Rotation
‣Press the clockwise or counter clockwise button to change the
rotation of the laser head.
Scanning mode
‣To focus the laser beam between two points press the scanning mode
button. Pressing the button multiple times will adjust the angle of the beam.
‣To cancel scan mode press the scanning mode button several times
to cycle through to full rotation.
Table of contents
Other General Measuring Instrument manuals
General
General DAF800 User manual
General
General MM9 User manual
General
General DAMP60 User manual
General
General CA10 User manual
General
General PalmScope DCS950 User manual
General
General DT4208SD User manual
General
General VM8205SD User manual
General
General SAM990DW User manual
General
General 24x User manual
General
General TA500 User manual
General
General DLM112SD User manual
General
General XL1G User manual
General
General 50-EB-3 Parts list manual
General
General DT4208SD User manual
General
General DMM51FSG User manual
General
General DM8252 User manual
General
General EP8709 User manual
General
General DSM402SD User manual
General
General EMF1394DL User manual
General
General MMD7003 User manual
