Extech Instruments 407820 User manual
User's Manual
Heavy Duty Digital Torque Meter
Model 407820
Introduction
Congratulations on your purchase of the Extech Heavy Duty Torque Meter,
Model 407820. This professional device measures torque in three ranges with
1.5% basic accuracy. Advanced functions include Peak and Data Hold, Record
Mode, and RS-232 PC Interface. Careful use of this meter will provide years of
reliable service.
407820
FAST/SLOW
POWER
RECORD/RECALL
PEAK RESOLUTION
HOLD
UNIT
SENSOR
ZERO
Torque
Meter
Kg cm
2
Model 407820 Version 3.0 August 20052
Specifications
General Specifications
Display 3-½ digit (2000 count) multi-function LCD
Units of Measure Kilogram-centimeter (kg-cm)
Pound-inch (lb-in)
Newton-centimeter (N-cm)
Resolution Programmable High or Low resolution (see range
specifications)
Meter Power 9V battery
Power consumption 12mA (approx.)
Auto Power Off Meter turns off after 10 minutes (can be defeated)
Max/Min Record/Recall Records highest (MAX) and lowest (MIN) readings
Data Hold Displayed reading can be held on the LCD by
pushbutton
Response Time Fast (125ms) and Slow (334ms); selectable
PC Interface Built-in RS-232 jack; Optional data acquisition software
Operating conditions Temperature: 32 to 122oF (0 to 50oC); Humidity < 80%
RH
Dimensions Meter: 7.1 x 2.8 x 1.3" (180 x 72 x 32mm)
Chuck: 1.9" (48mm) head diameter [6.3" (160mm)
handle] 0.5” (12.7mm) opening size
Weight Meter: 0.5 lbs. (225g); Chuck: 1.46 lbs (665g)
Accessories Torque chuck, chuck key, 9V battery, and rubber
holster with table-top stand
Range Specifications
Unit Range High
resolution Low
resolution
Accuracy
kg-cm 15 Kg-cm 0.01 kg-cm 0.1 kg-cm
lb-inch 12.99 lb-in 0.01 lb-in 0.1 lb-in
N-cm 147.1 N-cm 0.1 N-cm 1 N-cm
±(1.5% + 5d)
of
FULL SCALE
WARNING: DO NOT exceed the meter’s specified torque limit (refer to Range
Specification for range limits). Exceeding the torque limit can permanently
disable the sensor load cell.
Model 407820 Version 3.0 August 20053
Meter Description
1. Sensor Input
2. RS-232 PC Interface jack
3. LCD Display
4. Keypad
5. Rubber Protective Holster
6. Battery compartment on rear (rubber protective jacket must be removed
from meter to access the rear battery compartment)
7. Chuck
407820
FAST/SLOW
POWER
RECORD/RECALL
PEAK RESOLUTION
HOLD
UNIT
SENSOR
ZERO
Torque
Meter
Kg cm
2
1
2
3
4
5
6
7
Model 407820 Version 3.0 August 20054
Meter Operation
Connecting the Sensor
1. This meter accepts only the supplied 15 kg chuck. Push the SENSOR button
to confirm the 15 kg chuck; the LCD should read '15' when the button is
pressed.
2. Connect the chuck's cable to the input jack at the top of the meter.
3. Remove the chuck from the meter when the meter is not in use.
Powering the meter
1. The meter is powered by a 9V battery located in the rear battery
compartment. Note that the meter's protective rubber jacket must be
removed to access the battery compartment.
2. Press the POWER button to turn the meter on.
3. Press the POWER button again to turn the meter off.
Selecting the unit of measure
1. Use the UNIT button to scroll through the available measurement units. Each
selection is reflected on the LCD.
2. The available units are: pound-inch (lb-in), kilogram-centimeter (kg-cm), and
Newton-centimeter (N-cm).
Selecting the resolution
1. Use the RESOLUTION button to select the desired resolution, Low or High.
The selections are listed in the Range Specifications earlier in this manual.
2. Use the high resolution setting when the measurement is in the lower area of
the measurement range. Use the low resolution setting when the
measurement is in the higher regions of the measurement range.
Selecting the response time
The meter can be configured as fast responding (125ms) or slow responding
(334ms). Fast response is used to capture readings that are changing rapidly.
Slow response if used for average readings or slowly changing torque readings.
To select the response time:
1. Press the FAST/SLOW button.
2. The LCD will display 'F' for fast response or 'S' for slow response.
Taking measurements
1. Place a driver bit into the chuck.
2. Tighten the chuck using the supplied chuck key.
3. Push the ZERO button to zero the display.
4. Apply force to the device under test and view the Torque reading on the
meter's LCD.
WARNING: DO NOT exceed the meter’s specified torque limit (refer to Range
Specification for range limits). Exceeding the torque limit can permanently
disable the sensor load cell.
Model 407820 Version 3.0 August 20055
Data Hold
1. Press the HOLD button to freeze the displayed reading. The LCD will display
the icon 'HOLD' when Data Hold is engaged.
2. Press the HOLD button to de-activate this feature. The 'HOLD' icon will
switch off.
3. Note that Data Hold is not available while the meter is in the Max/Min Record
mode.
Peak Hold
1. Press the PEAK button to activate the Peak Hold feature. The LCD will
display 'PEAK' when Peak Hold is engaged.
2. The meter will now display only the highest reading. Each time a higher
reading is encountered the LCD will update.
3. Press the PEAK button to de-activate this feature. The 'PEAK' icon will switch
off.
4. Note that Peak Hold is not available while the meter is in the Max/Min Record
mode.
RECORD / RECALL and Max/Min Data Recording
The Max/Min feature stores the maximum reading and minimum reading while
the user takes measurements. The Max and the Min readings can later be
recalled.
1. Press the RECORD/RECALL button to activate this feature. The LCD will
display the ‘REC’ icon and the meter will begin monitoring the highest (Max)
and lowest (Min) readings.
2. After measurements are made, press the button again to view the Max
reading. The ‘MAX’ icon will appear on the LCD along with the highest
reading.
3. Press again to view the minimum (MIN) reading. The 'MIN' display icon will
appear on the LCD along with the lowest reading.
4. To exit this mode, press and hold the RECORD / RECALL button until the
‘REC’ indicator switches off. Note that exiting this mode clears the MAX and
MIN values.
RS-232 PC Interface
The optically isolated RS-232 PC Interface port is located on top of the meter
next to the sensor jack. A Data Acquisition Software package that includes
WindowsTM software and a meter-to-PC interface cable can be obtained from
Extech or an authorized distributor. The Part Number for the kit is 407001.
Instructions for use are supplied with the kit.
Model 407820 Version 3.0 August 20056
Support line (781) 890-7440
Product specifications subject to change without notice
For the latest version of this User’s Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bear Hill Rd., Waltham, MA 02451
Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects
in parts and workmanship for one year from date of shipment (a six month limited warranty
applies to sensors and cables). If it should become necessary to return the instrument for
service during or beyond the warranty period, contact the Customer Service Department at
(781) 890-7440 ext. 210 for authorization or visit our website www.extech.com for contact
information. A Return Authorization (RA) number must be issued before any product is
returned to Extech. The sender is responsible for shipping charges, freight, insurance and
proper packaging to prevent damage in transit. This warranty does not apply to defects
resulting from action of the user such as misuse, improper wiring, operation outside of
specification, improper maintenance or repair, or unauthorized modification. Extech
specifically disclaims any implied warranties or merchantability or fitness for a specific
purpose and will not be liable for any direct, indirect, incidental or consequential damages.
Extech's total liability is limited to repair or replacement of the product. The warranty set
forth above is inclusive and no other warranty, whether written or oral, is expressed or
implied.
Calibration and Repair Services
Extech offers repair and calibration services for the products we sell. Extech also
provides NIST certification for most products. Call the Customer Service Department for
information on calibration services available for this product. Extech recommends that
annual calibrations be performed to verify meter performance and accuracy.
Copyright ©2005 Extech Instruments Corporation
All rights reserved including the right of reproduction in whole or in part in any form.
Table of contents
Other Extech Instruments Measuring Instrument manuals
Extech Instruments
Extech Instruments LT250W User manual
Extech Instruments
Extech Instruments CO52 User manual
Extech Instruments
Extech Instruments 445580 User manual
Extech Instruments
Extech Instruments TM100 User manual
Extech Instruments
Extech Instruments 401027 User manual
Extech Instruments
Extech Instruments HD780 User manual
Extech Instruments
Extech Instruments ExStik RE300 User manual
Extech Instruments
Extech Instruments DC400 User manual
Extech Instruments
Extech Instruments HDV7C-A2-39-HD-1 User manual
Extech Instruments
Extech Instruments SDL600-NIST User manual
Extech Instruments
Extech Instruments CT-3060 User manual
Extech Instruments
Extech Instruments EX810 User manual
Extech Instruments
Extech Instruments 700 Series User manual
Extech Instruments
Extech Instruments HD350 User manual
Extech Instruments
Extech Instruments 461830 User manual
Extech Instruments
Extech Instruments 407730 User manual
Extech Instruments
Extech Instruments SL355 User manual
Extech Instruments
Extech Instruments 382075 User manual
Extech Instruments
Extech Instruments FM100 User manual
Extech Instruments
Extech Instruments TKG100 User manual
