ETC Source Four LED Series User manual

Product information and specifications subject to change.

Part Number:

7064M1200

Rev A

Released: 2011-07

User Manual

Rev A

Source Four®Fresnel

ETC permits the reproduction of materials in this manual only for non-commercial purposes. All other rights are

reserved by ETC.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

ETC

, Emphasis

, Expression

, Insight™, Imagine™, Focus™, Express™, Unison

, Obsession™ II, ETCNet2™,

EDMX™, Source Four

, Revolution

, Sensor® are either registered trademarks or trademarks of Electronic

Theatre Controls, Inc. in the United States and other countries.

All other trademarks, both marked and not marked, are the property of their respective owners.

Table of Contents

Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Lamp Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

HPL Lamp Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installing and Replacing the Lamp. . . . . . . . . . . . . . . . . . . . . . . .3

Field Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Accessory Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Yoke Balance Point Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Fixture Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Replacing the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Cleaning the Glass Lens and Reflector . . . . . . . . . . . . . . . . . . .11

Basic Assembly 1

Basic Assembly

Figure-1 Source Four Fresnel fixture components.

WARNING:

Please note the following safety warnings before use:

Do not use this fixture with a damaged power lead. If the power lead

(cordset) is damaged, it must be replaced.

Do not mount the fixture on or near combustible surfaces.

Do not operate the fixture without a lens installed.

Always hang the fixture with the accessory door in the locked position.

Field angle adjustment

knob

Yoke

Color frame holder

Fresnel lens

Safety screen

(CE markets only)

Lamp holder base

Accessory holder door

Lamp door

Lamp

2Source Four Fresnel User Manual

Lamp Information

HPL Lamp Table

CAUTION:

Do not use lamps other than the HPL in Source Four fixtures. Use of lamps other

than HPL will void UL/cUL safety compliance and your warranty.

Lamp code Watts Volts Initial Lumen Color temp. Average rated life

HPL 550/77* 550 77 16,170 3,250° 300 hours

HPL 550/77X* 550 77 12,160 3,050° 2000 hours

HPL 750/115 750 115 21,900 3,250°K 300 hours

HPL 750/115X 750 115 16,400 3,050° 1500 hours

HPL 575/115 575 115 16,520 3,250°K 300 hours

HPL 575/115X 575 115 12,360 3,050°K 2000 hours

HPL 375/115 375 115 10,540 3,250°K 300 hours

HPL 375/115X 375 115 8,000 3,050°K 1000 hours

HPL 750/120 750 120 21,900 3,250°K 300 hours

HPL 750/120X 750 130 16,400 3,0500°K 1500 hours

HPL 575/120 575 120 16,520 3,250°K 300 hours

HPL 575/120X 575 120 12,360 3,050°K 2000 hours

HPL 750/230 750 230 19,750 3,200°K 300 hours

HPL 750/230X 750 230 15,600 3,050°K 1500 hours

HPL 575/230 575 230 14,900 3,200°K 400 hours

HPL 575/230X 575 230 11,780 3,050°K 1500 hours

HPL 375/230X 375 230 7,250 3,000°K 1000 hours

HPL 750/240 750 240 19,750 3,200°K 300 hours

HPL 750/240X 750 240 15,600 3,050°K 1500 hours

HPL 575/240 575 240 14,900 3,050°K 400 hours

HPL 575/240X 575 240 11,780 3,050°K 1500 hours

HPL 375/240X 375 240 7,250 3,000°K 1000 hours

* To be used with ETC Dimmer Doubler™

Lamp Information 3

Installing and Replacing the Lamp

A lamp must be installed before you use the fixture.

Figure-2 Lamp door on bottom of the fixture.

Step 1: Disconnect power to the fixture before installing or replacing the lamp.

Step 2: On the bottom of the fixture, turn the latch on the lamp door one-quarter turn and then

open the door.

Step 3: Remove the lamp holder assembly by turning the knurled knob counterclockwise to

release the lamp socket assembly.

Note:

Verify that the HPL lamp you intend to install is suitable for your facility’s voltage;

115-, 120-, 230-, and 240-volt HPL lamps are available.

See HPL Lamp Table, page 2. Operating HPL lamps above their rated voltage

reduces lamp life and can cause premature lamp failure.

WARNING:

Unplug the fixture and allow it to cool down before attempting to change the

lamp.

Lamp door latch

Lamp door

4Source Four Fresnel User Manual

Step 4: Twist the lamp socket assembly counterclockwise one quarter turn and remove from the

fixture.

Figure-3 Remove lamp with quarter turn counterclockwise.

Step 5: If replacing a lamp, carefully remove the old lamp from the lamp socket assembly.

Step 6: Holding the new HPL lamp by the base, remove it from its box.

Step 7: Align the flat sides of the lamp base with the retention brackets on either side of the

socket in the lamp holder assembly as shown in Figure-3.

CAUTION:

The socket assembly remains connected to the fixture by means of its electrical

leads. Do pull or place undue stress on the wired assembly.

CAUTION:

Use caution when installing or replacing any lamp.

When installing and replacing lamp, be sure to point the lamp away from your face

and away from others before inserting it firmly into the assembly.

This may prevent injuries if the lamp should break.

Note:

To avoid premature lamp failure, do not touch the lamp glass. If you do, clean it

carefully with isopropyl alcohol and a clean lint-free cloth. Allow to dry before

operation.

Lamp holder

assembly

Turn to

remove

INCORRECT

CORRECT

Lamp Information 5

Step 8: Push down on the lamp base until the lamp seats firmly. When properly installed, the top

of the lamp’s base will be even with the top edges of the retention brackets.

Step 9: Reinstall the lamp holder assembly into its socket in the fixture so that the arrow points

towards the “unlock” icon on the socket.

Step 10: Turn the lamp holder assembly clockwise one-quarter turn so that the arrow points to the

“lock” icon.

Step 11: Turn the knurled knob clockwise to secure the lamp holder assembly.

Step 12: Close the lamp housing door and turn the latch to secure the door.

CAUTION:

Improperly installed lamps and lamp holder assemblies cause premature lamp

failure and socket problems.

6Source Four Fresnel User Manual

Field Angle Adjustment

You can adjust the field angle of the fixture from 20 to 65° with the field angle adjustment knob.

Step 1: Lift the locking lever to unlock the field angle adjustment knob.

Figure-4 Field angle adjustment knob and locking lever.

Step 2: Do one of the following.

• To reduce the field angle, turn the focus dial counterclockwise.

• To enlarge the field angle, turn the focus dial clockwise.

Figure-5 Field Adjustment from flood to spot.

Step 3: To lock the focus dial, press the locking lever into place.

CAUTION:

The focus knob does not rotate 360°. Do not attempt to exceed limit.

Locking lever

Field angle

adjustment knob

Focus knob in

flood position

Focus knob in

spot position

65° field angle

20° field angle

Other manuals for Source Four LED Series

This manual suits for next models

Table of contents

Other ETC Lighting Equipment manuals

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions