ETC Fos/4 Fresnel User manual

fos/4 Fresnel

User Manual

Version 1.1.0

Part Number: 7470M1200-1.1.0 Rev: B

Released: 2020-10

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Help from ETC Technical Services 2

Safety 3

Overview 5

Fixture 5

User Interface 6

Set Up and Focus the Fixture 7

Mount the Fixture 7

Add Accessories 7

Connect Power and Data 8

Focus the Fixture 8

Use Fixture in DMX Mode 9

Set DMXAddress 9

Set DMXMode 10

Set DMX Loss Behavior 12

Use Fixture in Stand-aloneMode 13

Studio Mode 14

Color Mode 15

Preset Mode 16

Effects Mode 17

Set Up Wireless Control 18

Set Up Multiverse Wireless Communication 18

Configure Fixtures Wirelessly Using the Set LightApp 18

Control and Customize the Display 19

Lock the Display 19

Adjust the Display Backlight and Display Timeout 19

Troubleshooting and Maintenance 20

Troubleshooting Checklist 20

Test the Emitters 21

View Diagnostic Data 21

View Battery Level 22

Export Fixture Data for Troubleshooting 22

Restore Default Settings 23

Update Firmware 23

Backup and Restore the Fixture Configuration 24

Clean the Lens 24

Specifications and Reference 25

Environment 25

Dimensions and Weight 25

Electrical 25

RDM Parameters 26

Fixture Compliance 26

Wireless Radio Compliance 26

Licensed Software 27

ii fos/4 Fresnel User Manual

Introduction 1

Introduction

The fos/4 Fresnel is a shapable wash light with top quality, highly tunable output. The fos/4

Fresnel is available in two array types:

•

Lustr X8: The next generation of the Lustr color system incorporates deep red into the

already amazing x7 mix to create an even more rich, vibrant X8 color palette.

•

Daylight HDR: Years of research resulted in an LED mix that yields the highest quality

tunable white light, optimized for studio use.

2 fos/4 Fresnel User Manual

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this document, try the ETC

support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none

of these resources are sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices outside of normal business

hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

Americas United Kingdom

ETC, Inc. ETC Ltd

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

service@etcconnect.com techservltd@etcconnect.com

Asia Germany

ETCAsia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong techserv-germany@etcconnect.com

+852 2799 1220

techserv-asia@etcconnect.com

France

ETC France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservltd@etcconnect.com

Introduction 3

Safety

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including

the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at

heights where it will not readily be subjected to

tampering by unauthorized personnel.

•

The use of accessory equipment not

recommended by the manufacturer

may cause an unsafe condition.

•

Do not use this equipment for other

than intended use.

SAVE THESE INSTRUCTIONS

Note:

The light source in this luminaire is not user-replaceable, and must be replaced

only by a qualified technician. Contact ETC Customer Support for assistance.

WARNING: Note the following safety warnings before use:

•

Use the fixture in dry locations only, where humidity does not exceed

90 percent (non-condensing).

•

Connect the fixture to a non-dimmable power source in order to avoid

damage to the fixture's internal power supply and other electrical

components. Using a dimmable power source can damage the fixture

and will void the warranty.

•

Disconnect the fixture from power and DMX and allow it to cool before

installing accessories or performing any cleaning and maintenance.

•

Only use mounting hardware that is rated for the total weight of the

fixture and accessories.

•

In addition to primary suspension, attach a safety cable (or other

approved safety device) to the fixture. Safety cables must be rated to

support ten times the fixture weight. Consult local standards to ensure

that safety cables meet all requirements. See

Mount the Fixture on

page7

•

Check that the accessory holder is locked and that any accessory safety

cables are connected before mounting the fixture.

•

Do not mount the fixture on or near a flammable surface.

•

Do not operate the fixture without the lens installed.

•

Do not use this fixture with a damaged power lead. If the power lead

(cord set) is damaged, it must be replaced.

•

Do not use this fixture if the lens is deeply scratched or cracked. You

must replace the lens when it is damaged.

4 fos/4 Fresnel User Manual

AVERTISSEMENT : Prendre connaissance des avertissements de sécurité

suivants avant toute utilisation :

•

Débranchez le projecteur de son alimentation et du DMX et laissez-le

refroidir avant d’installer des accessoires ou d’effectuer un nettoyage

ou un entretien.

•

N’utilisez que de la quincaillerie de montage adaptée au poids total

des projecteurs et des accessoires.

•

En plus de la suspension principale, fixez une chaîne de sécurité (ou

tout autre dispositif de sécurité homologué) au projecteur. Les chaînes

de sécurité doivent être en mesure de supporter dix fois le poids du

projecteur. Consultez les normes locales pour vous assurer que les

câbles de sécurité respectent toutes les exigences.

•

Vérifiez que le porte-accessoires est verrouillé et que les élingues de

tous les accessoires sont bien attachées avant de monter le projecteur.

•

Ne pas installer le projecteur sur ou à côté d’une surface inflammable.

•

N’utilisez pas le projecteur sans que la lentille soit installée.

•

Ne pas utiliser ce projecteur avec un cordon d’alimentation

endommagé. Si le cordon d’alimentation (câble) est abîmé, il doit être

remplacé.

•

N’utilisez pas ce projecteur si la lentille présente des rayures ou des

fissures profondes. Il faut remplacer la lentille si elle est abîmée.

Overview 5

Overview

Fixture

AAccessory holder: Insert accessories into the two available slots from either side of the holder,

and then lock the holder. See

Add Accessories on page7

BYoke tilt-lock: Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the

position. If necessary, press the center button on the tilt-lock to adjust the tilt-lock position.

CAdjustable yoke: Loosen the bolts, and then shift the adjustable yoke forward or backward as

needed to balance the fixture. Tighten the bolts to secure. See

Add Accessories on page7

DZoom knob: Rotate the zoom knob on either side of the fixture to adjust from spot to flood.

ENFC(Near Field Communication) tag: Use the Set Light app to wirelessly configure the fixture,

with or without power applied to the fixture. See

Set Up Wireless Control on page18

FUser interface: View the fixture status, set the DMXaddress and mode, or set stand-alone

options.

GAntenna: For use when controlling the fixture using wireless DMX. See

Set Up Wireless Control

on page18

HSafety cable attachment point: See

Mount the Fixture on page7

IDMX In and DMX Thru connectors: Five-pin XLRconnectors for DMX/RDM in and thru.

JPower In and Power Thru connectors: powerCON®TRUE1 TOP connectors for power in and

power thru.

KBattery connector: Three-pin XLRconnector for battery power. Connect the fixture to battery

power only when AC power is not available. Maximum fixture output may be reduced when

6 fos/4 Fresnel User Manual

User Interface

Effects

Effect Flicker

Rate 200

Min 0%

Max Int 100%

DMX

ADisplay: The colors of options on the display correspond to the colors of the encoders below the

display (E) and the Intensity encoder to the right of the display(B).

BIntensity encoder:

•

When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the

fixture.

•

When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to

toggle between the current intensity and 0, or turn the Intensity encoder to modify the white

fields on the display. See

Use Fixture in Stand-aloneMode on page13

•

When navigating from the Main Menu screen, turn the Intensity encoder to scroll through

menu options, and then press the Intensity encoder to select a menu option.

CMenu button: Press to view the Main Menu screen and configure the fixture. Press the button

again to return to the previous screen when you are setting configuration options.

DFunction button: Press repeatedly to toggle through the following modes:

•

Studio: Use one of three studio (white light) presets, or customize the presets.

•

Color: Use one of 12 color presets, or customize the presets.

•

Preset: Use one of 12 presets (color preset + fade time), or customize the presets.

•

Effects: Use one of 12 effects, or customize the effects.

•

DMX: View and set DMX parameters for the fixture.

See

Use Fixture in Stand-aloneMode on page13

and

Use Fixture in DMX Mode on page9

EEncoders(Red, Green, Blue):The colors of encoders correspond to options on the display.

Press to activate the options at the bottom of the display, or turn to modify the values on the

display.

FUSB port: Use for updating firmware, saving and loading fixture configuration settings, or

saving error logs via a flash drive. See

Troubleshooting and Maintenance on page20

GUI lock: Set this switch to lock the UI. This prevents inadvertent changes to the UI. See

Lock the

Display on page19

Other manuals for fos/4 Fresnel

This manual suits for next models

Table of contents

Other ETC Lighting Equipment manuals

ETC

ETC Source 4WRD User manual

ETC

ETC Lustr+ User manual

ETC

ETC Desire Fresnel User manual

ETC

ETC IRIDEON AR500 User manual

ETC

ETC Source Four Revolution Scroller Cartridge User manual

ETC

ETC Source Four CE 405 User manual

ETC

ETC Source Four Revolution Scroller Cartridge User manual

ETC

ETC Source Four Mini LED User manual

ETC

ETC Echo User manual

ETC

ETC High End Systems SolaFrame 3000 User manual

ETC

ETC Source Four Revolution Rotating Wheel Module User manual

ETC

ETC Source Four LED Series Installation guide

ETC

ETC ArcSystem Pro D1 Series User manual

ETC

ETC Desire D40XTI User manual

ETC

ETC fos/4 Panel Pole-Operated Yoke User manual

ETC

ETC ArcSystem Pro Multi-Cell RDM User manual

ETC

ETC fos/4 Series User manual

ETC

ETC Source Four Mini CE User manual

ETC

ETC Express User manual

ETC

ETC Lustr+ User manual

ETC

ETC Source Four LED series User manual

ETC

ETC GDS BluesSystem User manual

ETC

ETC Source Four LED Series User manual

ETC

ETC Cyberlight LED User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions

ETC fos/4 Fresnel User manual

Popular Lighting Equipment manuals by other brands