BLOTZ B06-CS-101 User manual
6mm ‘D’ Tower Block Foyer
B06-CS-101
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Foyer (B06-CS-101)
Remove the pieces shown above from the sprue.
(The side walls are marked ‘L’ and ‘R’
respectively).
Glue the canopy and archway to the front of the
building as shown above.
Glue the front and side walls to the main support
as shown above. Allow to dry.
Remove the rear walls and rear canopy from the
sprue.
Glue the canopy to the rear wall then attach that
wall and the two side walls to the main support.
6mm ‘D’ Tower Block Middle
B06-CS-151
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Mid-Section (B06-CS-151)
Remove the pieces shown above from the sprue.
(The side walls are marked ‘L’ and ‘R’
respectively).
Glue the front and side walls to the main support as
shown above. Allow to dry.
Remove the rear walls from the sprue. (The
centre one is marked ‘B’.
Glue the walls into position. Allow to dry.
Glue the ‘C’ shaped supports to the buttom of
the walls as shown above.
6mm ‘D’ Tower Block Roo
B06-CS-201
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due
care and remember to cut away from yourself at all times.
During the construction of this model you may find it convenient to use pegs / elastic bands to hold
pieces in place while you allow glue to dry.
Roo Section (B06-CS-201)
Remove the pieces shown above from the sprue.
(The side walls are marked ‘L’ and ‘R’
respectively).
Glue the front and side walls to the roof piece as
shown above. Allow to dry.
Remove the rear walls from the sprue. (The
centre one is marked ‘B’. and glue them into
position.
Glue the ‘C’ supports into position as per the example
shown above.
Table of contents
Other BLOTZ Toy manuals
BLOTZ
BLOTZ B06-CS-100 User manual
BLOTZ
BLOTZ B10-CS-208 User manual
BLOTZ
BLOTZ B20-ST-102 User manual
BLOTZ
BLOTZ B20-ME-002 User manual
BLOTZ
BLOTZ B10-RD-103 User manual
BLOTZ
BLOTZ B15-CS-002 User manual
BLOTZ
BLOTZ B28-OW-203 User manual
BLOTZ
BLOTZ B10-MW-108 User manual
BLOTZ
BLOTZ B28-AF-102 User manual
BLOTZ
BLOTZ Old West Store 3 User manual
BLOTZ
BLOTZ B28-VSF-013 User manual
BLOTZ
BLOTZ B28-WW2-301 User manual
BLOTZ
BLOTZ B28-WW2-303 User manual
BLOTZ
BLOTZ B28-SF-226 User manual
BLOTZ
BLOTZ Old West Store #7 User manual
BLOTZ
BLOTZ B15-MC-005 User manual
BLOTZ
BLOTZ B06-CS-006 User manual
BLOTZ
BLOTZ B28-VSF-010 User manual
BLOTZ
BLOTZ B20-DIDG Series User manual
BLOTZ
BLOTZ B10-CS-203 User manual
