Atmel AT90PWM2 User manual

Features

•High Performance, Low Power AVR ® 8-bit Microcontroller

•Advanced RISC Architecture

– 129 Powerful Instructions - Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 1 MIPS throughput per MHz

– On-chip 2-cycle Multiplier

•Data and Non-Volatile Program Memory

– 8K Bytes Flash of In-System Programmable Program Memory

• Endurance: 10,000 Write/Erase Cycles

– Optional Boot Code Section with Independent Lock Bits

•In-System Programming by On-chip Boot Program

•True Read-While-Write Operation

– 512 Bytes of In-System Programmable EEPROM

•Endurance: 100,000 Write/Erase Cycles

– 512 Bytes Internal SRAM

– Programming Lock for Flash Program and EEPROM Data Security

•On Chip Debug Interface (debugWIRE)

•Peripheral Features

– Two or three 12-bit High Speed PSC (Power Stage Controllers) with 4-bit

Resolution Enhancement

• Non Overlapping Inverted PWM Output Pins With Flexible Dead-Time

• Variable PWM duty Cycle and Frequency

• Synchronous Update of all PWM Registers

• Auto Stop Function for Event Driven PFC Implementation

• Less than 25 Hz Step Width at 150 kHz Output Frequency

• PSC2 with four Output Pins and Output Matrix

– One 8-bit General purpose Timer/Counter with Separate Prescaler and Capture

Mode

– One 16-bit General purpose Timer/Counter with Separate Prescaler, Compare

Mode and Capture Mode

– Programmable Serial USART

• Standard UART mode

• 16/17 bit Biphase Mode for DALI Communications

– Master/Slave SPI Serial Interface

– 10-bit ADC

• Up To 11 Single Ended Channels and 2 Fully Differential ADC Channel Pairs

• Programmable Gain (5x, 10x, 20x, 40x on Differential Channels)

• Internal Reference Voltage

– 10-bit DAC

– Two or three Analog Comparator with Resistor-Array to Adjust Comparison

Voltage

– 4 External Interrupts

– Programmable Watchdog Timer with Separate On-Chip Oscillator

•Special Microcontroller Features

– Low Power Idle, Noise Reduction, and Power Down Modes

– Power On Reset and Programmable Brown Out Detection

– Flag Array in Bit-programmable I/O Space (4 bytes) 4317I–AVR–01/08

8-bit

Microcontroller

with 8K Bytes

In-System

Programmable

Flash

AT90PWM2

AT90PWM3

AT90PWM2B

AT90PWM3B

24317I–AVR–01/08

AT90PWM2/3/2B/3B

– In-System Programmable via SPI Port

– Internal Calibrated RC Oscillator ( 8 MHz)

– On-chip PLL for fast PWM ( 32 MHz, 64 MHz) and CPU (16 MHz)

•Operating Voltage: 2.7V - 5.5V

•Extended Operating Temperature:

– -40°C to +105°

1. History

This datasheet deals with product characteristics of AT90PW2 and AT90WM3. It will be updated

as soon as characterization will be done.

2. Disclaimer Typical values contained in this datasheet are based on simulations and characterization of

other AVR microcontrollers manufactured on the same process technology. Min and Max val-

ues will be available after the device is characterized.

Product Package 12 bit PWM with

deadtime ADC

Input ADC

Diff Analog

Compar Application

AT90PWM2

AT90PWM2B SO24 2 x 2 8 1 2 One fluorescent ballast

AT90PWM3

AT90PWM3B SO32,

QFN32 3 x 2 11 2 3 HID ballast, fluorescent ballast,

Motor control

Product Revision

AT90PWM2

AT90PWM3 First revision of parts, only for running production.

AT90PWM2B

AT90PWM3B

Second revision of parts, for all new developments.

The major changes are :

• complement the PSCOUT01, PSCOUT11, PSCOUT21 polarity in

centered mode - See “PSCn0 & PSCn1 Basic Waveforms in Center

Aligned Mode” on page 139.

• Add the PSC software triggering capture - See “PSC 0 Input Capture

• Add bits to read the PSC output activity - See “PSC0 Interrupt Flag

• Add some clock configurations - See “Device Clocking Options Select

AT90PWM2B/3B” on page 31.

• Change Amplifier Synchonization - See “Amplifier” on page 252. and

See “” on page 255.

• Correction of the Errata - See “Errata” on page 350.

4317I–AVR–01/08

AT90PWM2/3/2B/3B

3. Pin Configurations

Figure 3-1. SOIC 24-pin Package

Figure 3-2. SOIC 32-pin Package

AT90PWM2/2B

SOIC24

(PSCOUT00/XCK/SS_A) PD0

(RESET/OCD) PE0

(PSCIN0/CLKO) PD1

(PSCIN2/OC1A/MISO_A) PD2

(TXD/DALI/OC0A/SS/MOSI_A) PD3

VCC

GND

(MISO/PSCOUT20) PB0

(MOSI/PSCOUT21) PB1

(OC0B/XTAL1) PE1

(ADC0/XTAL2) PE2

ADC1/RXD/DALI/ICP1A/SCK_A) PD4

PB7(ADC4/PSCOUT01/SCK)

PB6 (ADC7/ICP1B)

PB5 (ADC6/INT2)

PB4 (AMP0+)

PB3 (AMP0-)

AREF

GND

AVCC

PB2 (ADC5/INT1)

PD7 (ACMP0)

PD6 (ADC3/ACMPM/INT0)

PD5 (ADC2/ACMP2)

AT90PWM3/3B

SOIC 32

(PSCOUT00/XCK/SS_A) PD0

(INT3/PSCOUT10) PC0

(RESET/OCD) PE0

(PSCIN0/CLKO) PD1

(PSCIN2/OC1A/MISO_A) PD2

(TXD/DALI/OC0A/SS/MOSI_A) PD3

(PSCIN1/OC1B) PC1

VCC

GND

(T0/PSCOUT22) PC2

(T1/PSCOUT23) PC3

(MISO/PSCOUT20) PB0

(MOSI/PSCOUT21) PB1

(OC0B/XTAL1) PE1

(ADC0/XTAL2) PE2

(ADC1/RXD/DALI/ICP1A/SCK_A) PD4

PB7(ADC4/PSCOUT01/SCK)

PB6 (ADC7/PSCOUT11/ICP1B)

PB5 (ADC6/INT2)

PC7 (D2A)

PB4 (AMP0+)

PB3 (AMP0-)

PC6 (ADC10/ACMP1)

AREF

GND

AVCC

PC5 (ADC9/AMP1+)

PC4 (ADC8/AMP1-)

PB2 (ADC5/INT1)

PD7 (ACMP0)

PD6 (ADC3/ACMPM/INT0)

PD5 (ADC2/ACMP2)

44317I–AVR–01/08

AT90PWM2/3/2B/3B

Figure 3-3. QFN32 (7*7 mm) Package.

3.1 Pin Descriptions

(PSCIN2/OC1A/MISO_A) PD2

(

TXD/DALI/OC0A/SS/MOSI_A) PD3

(PSCIN1/OC1B) PC1

VCC

GND

(T0/PSCOUT22) PC2

(T1/PSCOUT23) PC3

(MISO/PSCOUT20) PB0

PB4 (AMP0+)

PB3 (AMP0-)

PC6 (ADC10/ACMP

AREF

AGND

AVCC

PC5 (ADC9/AMP1+)

PC4 (ADC8/AMP1-)

(MOSI/PSCOUT21) PB1

(OC0B/XTAL1) PE1

(ADC0/XTAL2) PE2

(

ADC1/RXD/DALI/ICP1_A/SCK_A) PD4

(ADC2/ACMP2 ) PD5

(ADC3/ACMPM/INT0) PD6

(ACMP0) PD7

(ADC5/INT1) PB2

PD1

(PSCIN0/CLKO)

PE0

(RESET/OCD)

PC0

(INT3/PSCOUT10)

PD0

(PSCOUT00/XCK/SS_A)

PB7 (ADC4/PSCOUT01/SCK)

PB6 (ADC7/PSCOUT11/ICP1B)

PB5 (ADC6/INT2)

PC7 (D2A)

AT90PWM3/3B QFN 32

Table 3-1. Pin out description

S024 Pin

Number SO32 Pin

Number QFN32 Pin

Number Mnemonic Type Name, Function & Alternate Function

795GNDPowerGround: 0V reference

18 24 20 AGND Power Analog Ground: 0V reference for analog part

4317I–AVR–01/08

AT90PWM2/3/2B/3B

6 8 4 VCC power Power Supply:

17 23 19 AVCC Power Analog Power Supply: This is the power supply voltage for analog

part

For a normal use this pin must be connected.

19 25 21 AREF Power Analog Reference : reference for analog converter . This is the

reference voltage of the A/D converter. As output, can be used by

external analog

8128PBOI/O

MISO (SPI Master In Slave Out)

PSCOUT20 output

9139PB1I/O

MOSI (SPI Master Out Slave In)

PSCOUT21 output

16 20 16 PB2 I/O ADC5 (Analog Input Channel5 )

INT1

20 27 23 PB3 I/O AMP0- (Analog Differential Amplifier 0 Input Channel )

21 28 24 PB4 I/O AMP0+ (Analog Differential Amplifier 0 Input Channel )

22 30 26 PB5 I/O ADC6 (Analog Input Channel 6)

INT 2

23 31 27 PB6 I/O ADC7 (Analog Input Channel 7)

ICP1B (Timer 1 input capture alternate input)

PSCOUT11 output (see note 1)

24 32 28 PB7 I/O PSCOUT01 output

ADC4 (Analog Input Channel 4)

SCK (SPI Clock)

230PC0I/O

PSCOUT10 output (see note 1)

INT3

73PC1I/O

PSCIN1 (PSC 1 Digital Input)

OC1B (Timer 1 Output Compare B)

10 6 PC2 I/O T0 (Timer 0 clock input)

PSCOUT22 output

11 7 PC3 I/O T1 (Timer 1 clock input)

PSCOUT23 output

21 17 PC4 I/O ADC8 (Analog Input Channel 8)

AMP1- (Analog Differential Amplifier 1 Input Channel )

22 18 PC5 I/O ADC9 (Analog Input Channel 9)

AMP1+ (Analog Differential Amplifier 1 Input Channel )

26 22 PC6 I/O ADC10 (Analog Input Channel 10)

ACMP1 (Analog Comparator 1 Positive Input )

29 25 PC7 I/O D2A : DAC output

Table 3-1. Pin out description (Continued)

S024 Pin

Number SO32 Pin

Number QFN32 Pin

Number Mnemonic Type Name, Function & Alternate Function

64317I–AVR–01/08

AT90PWM2/3/2B/3B

1. PSCOUT10 & PSCOUT11 are not present on 24 pins package

4. Overview The AT90PWM2/2B/3/3B is a low-power CMOS 8-bit microcontroller based on the AVR

enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the

AT90PWM2/2B/3/3B achieves throughputs approaching 1 MIPS per MHz allowing the system

designer to optimize power consumption versus processing speed.

1129PD0I/O

PSCOUT00 output

XCK (UART Transfer Clock)

SS_A (Alternate SPI Slave Select)

3432PD1I/O

PSCIN0 (PSC 0 Digital Input )

CLKO (System Clock Output)

451PD2I/O

PSCIN2 (PSC 2 Digital Input)

OC1A (Timer 1 Output Compare A)

MISO_A (Programming & alternate SPI Master In Slave Out)

562PD3I/O

TXD (Dali/UART Tx data)

OC0A (Timer 0 Output Compare A)

SS (SPI Slave Select)

MOSI_A (Programming & alternate Master Out SPI Slave In)

12 16 12 PD4 I/O

ADC1 (Analog Input Channel 1)

RXD (Dali/UART Rx data)

ICP1A (Timer 1 input capture)

SCK_A (Programming & alternate SPI Clock)

13 17 13 PD5 I/O ADC2 (Analog Input Channel 2)

ACMP2 (Analog Comparator 2 Positive Input )

14 18 14 PD6 I/O ADC3 (Analog Input Channel 3 )

ACMPM reference for analog comparators

INT0

15 19 15 PD7 I/O ACMP0 (Analog Comparator 0 Positive Input )

2 3 31 PE0 I/O or I RESET (Reset Input)

OCD (On Chip Debug I/O)

10 14 10 PE1 I/O XTAL1: XTAL Input

OC0B (Timer 0 Output Compare B)

11 15 11 PE2 I/O XTAL2: XTAL OuTput

ADC0 (Analog Input Channel 0)

Table 3-1. Pin out description (Continued)

S024 Pin

Number SO32 Pin

Number QFN32 Pin

Number Mnemonic Type Name, Function & Alternate Function

4317I–AVR–01/08

AT90PWM2/3/2B/3B

4.1 Block Diagram

Figure 4-1. Block Diagram

The AVR core combines a rich instruction set with 32 general purpose working registers. All the

32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent

registers to be accessed in one single instruction executed in one clock cycle. The resulting

architecture is more code efficient while achieving throughputs up to ten times faster than con-

ventional CISC microcontrollers.

The AT90PWM2/2B/3/3B provides the following features: 8K bytes of In-System Programmable

Flash with Read-While-Write capabilities, 512 bytes EEPROM, 512 bytes SRAM, 53 general

purpose I/O lines, 32 general purpose working registers,three Power Stage Controllers, two flex-

ible Timer/Counters with compare modes and PWM, one USART with DALI mode, an 11-

channel 10-bit ADC with two differential input stage with programmable gain, a 10-bit DAC, a

programmable Watchdog Timer with Internal Oscillator, an SPI serial port, an On-chip Debug

system and four software selectable power saving modes.

8Kx8 Flash

Program

Memory

Instruction

Decoder

Program

Counter

Control Lines

32 x 8

General

Purpose

Registrers

ALU

Status

and Control

I/O Lines

EEPROM

512 bytes

Data Bus 8-bit

Data

SRAM

512 bytes

Direct Addressing

Indirect Addressing

Interrupt

Unit

SPI

Unit

Watchdog

Timer

3 Analog

Comparators

DAC

ADC

PSC 2/1/0

Timer 1

Timer 0

DALI USART

84317I–AVR–01/08

AT90PWM2/3/2B/3B

The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI ports and interrupt

system to continue functioning. The Power-down mode saves the register contents but freezes

the Oscillator, disabling all other chip functions until the next interrupt or Hardware Reset. The

ADC Noise Reduction mode stops the CPU and all I/O modules except ADC, to minimize switch-

ing noise during ADC conversions. In Standby mode, the Crystal/Resonator Oscillator is running

while the rest of the device is sleeping. This allows very fast start-up combined with low power

consumption.

The device is manufactured using Atmel’s high-density nonvolatile memory technology. The On-

chip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial

interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program

running on the AVR core. The boot program can use any interface to download the application

program in the application Flash memory. Software in the Boot Flash section will continue to run

while the Application Flash section is updated, providing true Read-While-Write operation. By

combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip,

the Atmel AT90PWM2/3 is a powerful microcontroller that provides a highly flexible and cost

effective solution to many embedded control applications.

The AT90PWM2/3 AVR is supported with a full suite of program and system development tools

including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators,

and evaluation kits.

4.2 Pin Descriptions

4.2.1 VCC Digital supply voltage.

4.2.2 GND Ground.

4.2.3 Port B (PB7..PB0)

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port B output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Port B also serves the functions of various special features of the AT90PWM2/2B/3/3B as listed

on page 69.

4.2.4 Port C (PC7..PC0)

Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port C output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Port C is not available on 24 pins package.

Port C also serves the functions of special features of the AT90PWM2/2B/3/3B as listed on page

72.

4317I–AVR–01/08

AT90PWM2/3/2B/3B

4.2.5 Port D (PD7..PD0)

Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port D output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port D pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Port D also serves the functions of various special features of the AT90PWM2/2B/3/3B as listed

on page 74.

4.2.6 Port E (PE2..0) RESET/ XTAL1/

XTAL2 Port E is an 3-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port E output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port E pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port E pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

If the RSTDISBL Fuse is programmed, PE0 is used as an I/O pin. Note that the electrical char-

acteristics of PE0 differ from those of the other pins of Port C.

If the RSTDISBL Fuse is unprogrammed, PE0 is used as a Reset input. A low level on this pin

for longer than the minimum pulse length will generate a Reset, even if the clock is not running.

The minimum pulse length is given in Table 9-1 on page 47. Shorter pulses are not guaranteed

to generate a Reset.

Depending on the clock selection fuse settings, PE1 can be used as input to the inverting Oscil-

lator amplifier and input to the internal clock operating circuit.

Depending on the clock selection fuse settings, PE2 can be used as output from the inverting

Oscillator amplifier.

The various special features of Port E are elaborated in “Alternate Functions of Port E” on page

77 and “Clock Systems and their Distribution” on page 29.

4.2.7 AVCC AVCC is the supply voltage pin for the A/D Converter. It should be externally connected to VCC,

even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-

pass filter.

4.2.8 AREF This is the analog reference pin for the A/D Converter.

4.3 About Code Examples

This documentation contains simple code examples that briefly show how to use various parts of

the device. These code examples assume that the part specific header file is included before

compilation. Be aware that not all C compiler vendors include bit definitions in the header files

and interrupt handling in C is compiler dependent. Please confirm with the C compiler documen-

tation for more details.

4317I–AVR–01/08

AT90PWM2/3/2B/3B

5. AVR CPU Core

5.1 Introduction This section discusses the AVR core architecture in general. The main function of the CPU core

is to ensure correct program execution. The CPU must therefore be able to access memories,

perform calculations, control peripherals, and handle interrupts.

5.2 Architectural Overview

Figure 5-1. Block Diagram of the AVR Architecture

In order to maximize performance and parallelism, the AVR uses a Harvard architecture – with

separate memories and buses for program and data. Instructions in the program memory are

executed with a single level pipelining. While one instruction is being executed, the next instruc-

tion is pre-fetched from the program memory. This concept enables instructions to be executed

in every clock cycle. The program memory is In-System Reprogrammable Flash memory.

Flash

Program

Memory

Instruction

Decoder

Program

Counter

Control Lines

32 x 8

General

Purpose

Registrers

ALU

Status

and Control

I/O Lines

EEPROM

Data Bus 8-bit

Data

SRAM

Direct Addressing

Indirect Addressing

Interrupt

Unit

SPI

Unit

Watchdog

Timer

Analog

Comparator

I/O Module 2

I/O Module1

I/O Module n

This manual suits for next models

Table of contents

Other Atmel Microcontroller manuals

Atmel

Atmel ATSAMB11 BluSDK SMART User manual

Atmel

Atmel 8051 User manual

Atmel

Atmel AVR XMEGA E Installation and operating instructions

Atmel

Atmel AT91SAM9 Installation and operating instructions

Atmel

Atmel AVR1306 User manual

Atmel

Atmel ATtiny26 User manual

Atmel

Atmel AVR AT90S2333 User manual

Atmel

Atmel AT90S1200 User manual

Atmel

Atmel AVR8015 Installation and operating instructions

Atmel

Atmel C51 Installation and operating instructions

Atmel

Atmel ATmega48A User manual

Atmel

Atmel AT88CK101BK8 Installation manual

Atmel

Atmel AVR ATtiny15L Owner's manual

Atmel

Atmel ATmega168PB Xplained Mini User manual

Atmel

Atmel AVR XMEGA-A3BU Installation and operating instructions

Atmel

Atmel AT90S2313 User manual

Atmel

Atmel AT88CK109STK3 Installation manual

Atmel

Atmel AVR32 STK1000 User manual

Atmel

Atmel 80C51 Installation and operating instructions

Atmel

Atmel AVR2131 User manual

Atmel

Atmel ATF15 DK3-U Series User manual

Atmel

Atmel develer DevelBoard Blue Quick user guide

Atmel

Atmel AVR1612 Installation and operating instructions

Atmel

Atmel AVR042 Installation and operating instructions

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide