Atmel ATSAMB11 BluSDK SMART User manual

ATSAMB11 BluSDK SMART

HID Mouse Device - Getting Started Guide

USER GUIDE

Introduction

The HID over GATT (HOGP) profile defined by the Bluetooth®SIG enables support of HID services over a

Bluetooth Low Energy (BLE) protocol stack using Generic Attribute profile (GATT). This allows devices

like keyboard or mouse implementing HOGP to connect to a compatible HOGP/BLE host device (e.g.:

Mobile Phone, Tablet, TV, etc.)

The HOGP Mouse device application example (referred as HID Mouse device in this document) supports

the following features:

Advertisement

Pairing

Services: HID Service and Device Information Service.

Report Mode (Mouse)

The HID Mouse device application example supports the following characteristics for HID service:

Protocol Mode

Report

Boot Mouse Input Report

Report Map

HID Information

HID Control Point

For the purpose of demonstration, the example application simulates the function of a mouse. Once the

handshake and connection procedure between a mobile phone and the Atmel®ATSAMB11 emulating a

mouse device example is completed, a mouse cursor will appear on the mobile device’s screen. Pressing

the button on the ATSAMB11 platform simulates movement of mouse in a pre-defined pattern as

described in later in this document.

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Table of Contents

1Purpose .....................................................................................................................3

2Demo Setup..................................................................................................................3

3Hardware Setup ...........................................................................................................3

4Software Setup.............................................................................................................4

4.1 Installation Steps...................................................................................................................................4

4.2 Build Procedure.....................................................................................................................................4

5Console Display...........................................................................................................6

6Running the Demo.......................................................................................................6

7BluSDK SMART Software Architecture....................................................................11

8ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........12

9Revision History ........................................................................................................13

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

1 Purpose

This getting started guide describes the setup of an Atmel ATSAMB11 Xplained board and bringing up an

example profile supplied as part of BluSDK SMART release. This document explains the bring-up of HID

Mouse device example application that is embedded as part of the software release package.

2 Demo Setup

3 Hardware Setup

Connect the ATSAMB11 board to the host PC using a Micro-USB cable.

Figure 3-1. EDBG USB Port

BLE Link

ATSAMB11

(HID Mouse Device

Application)

Android mobile phone

(HOGP Host role)

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

4 Software Setup

4.1 Installation Steps

1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer

(recommended)]

http://www.atmel.com/tools/ATMELSTUDIO.aspx.

2. Install the latest Atmel Software Framework.

This package will install the following examples within the Atmel Studio environment:

HID Device Application for ATSAMB11

4.2 Build Procedure

The following procedure is explained for ATSAMB11 application example.

1. Select New Example Project.

Figure 4-1. Creating a New Example Project

2. Select “SAMB11” in device family, enter “ble-hid mouse” in the search window, and expand Atmel

Corp Projects. The location and the name of the project can be selected in the respective fields.

Click OK.

Figure 4-2. Selecting HID Device Application from Example Projects

3. Accept the license Agreement. The studio will generate the BLE-HID Mouse project for ATSAMB11.

4. Build the solution.

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Figure 4-3. Building the HID Device Application

5. Download the application via the USB to the ATSAMB11 board by using the Device Programing

option available in Tools as shown below.

Figure 4-4. Selecting Device Programming Option

6. Inside the device programming the user has to select the correct configuration for the device and

finally program the device by using the program button.

Figure 4-5. Flashing the Application on Atmel MCU

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

5 Console Display

For the purpose of debugging, logging is made available through a serial console. The logging interface

utilizes the same COM port that connects to ATSAMB11. A serial port monitor application (for example

TeraTerm) shall be opened and attached to the appropriate COM port enumerated by the device on the

PC.

6 Running the Demo

1. Power on the ATSAMB11 by connecting the USB cable.

2. On the PC, open any Terminal Application (e.g. TeraTerm). Select the appropriate COM Port.

(Settings: Baudrate 115200, None Parity, one Stop bit, one Start bit, no Hardware Handshake.)

3. Press the Reset button on the ATSAMB11 board.

4. The board is now in advertising mode as shown below.

Figure 6-1. HID Keyboard Device in Advertising Mode

Initializing HID Mouse Application

HID Profile Configured

Initializing SAMB11

BLE-chip id : 0x002000B0

BD Address:0xF8F005F0B299, Address Type:0

Device Started Advertisement

5. The demo requires use of an Android mobile phone supporting HOGP. The HOGP profile is natively

supported in Android from version 4.4 (Android KitKat) and upwards. In Bluetooth settings scan for

the devices. The device with “ATMEL-HID” will be found as shown below. Click on “ATMEL-HID” to

get connected.

Figure 6-2. Mouse Device Discover on Bluetooth Device

6. Once the user clicks on “ATMEL-HID”, pairing procedure started.

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Figure 6-3. Pairing Process with HID Device

7. Once the pairing done connected device is listed in paired device.

Figure 6-4. Connected Device Inside Paired Devices

8. Console log on HID device side for pairing and connection procedure.

Figure 6-5. HID Mouse Log for Pairing and Connection Procedure

Initializing HID Mouse Application

HID Profile Configured

Initializing SAMB11

BLE-chip id:0x002000B0

BD Address:0xF8F005F0B299, Address Type:0

Device Started Advertisement

Connected to peer device with address 0x7b5bfc5cf8d0

Connection Handle 0

Remote device request pairing

Sending pairing response

AT_BLE_CONN_PARAM_UPDATE

Pairing procedure completed successfully

9. Once the device connected to host (Phone). User can select button for simulating mouse

movement.

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Figure 6-6. Press Button for Mouse Movement

10. For every press on button, the user can see corresponding cursor movement on HID host as

described below:

First 5 Button Press: Cursor moves right

Next 5 Button Press: Cursor moved down

Next 5 Button Press: Cursor moves left

Next 5 Button Press: Cursor moved up

The same sequence is repeated based on user input. A snapshot of the console logs are shown below.

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Figure 6-7. HID Device Console Log for Movement

Mouse Right Movement

Mouse Down Movement

Mouse Letf Movement

Mouse UP Movement

Figure 6-8. Mouse Cursor Position on Phone

ATSAMB11 BluSDK SMART –HID Mouse Device –Getting Started Guide [USER GUIDE]

Atmel-42603A-ATSAMB11-BluSDK-SMART-HID-Mouse-Device-Getting-Started-Guide_UserGuide_112015

Figure 6-9. Mouse Move Simulation

Other manuals for ATSAMB11 BluSDK SMART

Table of contents

Other Atmel Microcontroller manuals

Atmel

Atmel ATmega328PB Xplained Mini Installation and operating instructions

Atmel

Atmel AVR XMEGA AU series User manual

Atmel

Atmel AT40K Installation and operating instructions

Atmel

Atmel AT32UC3L064 User manual

Atmel

Atmel SAM4N Xplained Pro User manual

Atmel

Atmel AT91 ARM Thumb Installation and operating instructions

Atmel

Atmel AVR XMEGA E Installation and operating instructions

Atmel

Atmel ATBTLC1000 BluSDK User manual

Atmel

Atmel UC3-L0 Xplained Installation and operating instructions

Atmel

Atmel AVR32918 User manual

Atmel

Atmel AT89STK-09 User manual

Atmel

Atmel ATmega32M1 User manual

Atmel

Atmel AVR AT90CAN64 User manual

Atmel

Atmel ATmega645 Installation and operating instructions

Atmel

Atmel ATmega8 User manual

Atmel

Atmel megaAVR User manual

Atmel

Atmel AVR262 Installation and operating instructions

Atmel

Atmel MC320 User manual

Atmel

Atmel AVR2054 User manual

Atmel

Atmel AVR XMEGA-A3BU Installation and operating instructions

Atmel

Atmel AVR User manual

Atmel

Atmel AVR ATtiny15L Owner's manual

Atmel

Atmel develer DevelBoard Blue Quick user guide

Atmel

Atmel SMART ATSAMC21MOTOR User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide