Atdec Freestanding Quad User manual

Component Checklist

Bits Box

Important Notes

lEach Donut Clamp Assembly supports a maximum weight of 11.5kg (25lbs)

lThis product suits VESA compliant displays with 75mm x 75mm (3” x 3”) and

100mm x 100mm (4” x 4”) mounting hole patterns.

lThe manufacturer does not accept responsibility for incorrect installation

freestanding quad

Installation Instructions

visidec

Check you have received all parts against this component checklist prior to installation

Cable

Ball (x8)

M8x50mm

Screw

(x1)

Cable

Clip (x4) Extension

Clip (x16)

2.5mm Allen

Key (x1)

5mm Allen

Key (x1)

Mounting Screws

M4x10mm (x16)

M4x12mm (x16)

M4x16mm (x16)

TOOLS REQUIRED:

lPhillips Head Screw Driver

AAttach Upright Pole to Base Install Horizontal Support and Donut Clamp

Attach the Upright Pole to the Base

as shown below. Ensure the Cable

Slot faces towards the rear.

Follow steps below to attach the Horizontal Support and Donut Clamp

assembly onto the Upright Pole. Ensure the Cable Slots in all the Poles are

facing to the rear.

Horizontal

Support Donut(x1)

Donut

Clamp (x4)

Upright Pole

Base

B.2.

Slide the Horizontal Support

to desired position

Cable

Slot

Cable Slot

User

Upright Pole

Back

LOOSEN

TIGHTEN

POSITION

Repeat steps B.1, B.2 and B.3

for the 2nd set of Horizontal

Support and Donut Clamp

TIGHTEN

B.1.

Loosen the Hex screws in the

Horizontal Support Donut using

the supplied 5mm Allen Key

B.3.

Tighten supports firmly

using the supplied 5mm

Allen Key

5mm Allen Key

M8x50mm Screw

TIGHTEN

FIRMLY

IMPORTANT:

When tightening the Donut Clamp,

each of the Donut bolts must be

tightened evenly, as failure to do so

will damage the Donut Clamp. Do

not over-tighten as this may also result

in damage.

Adjust Ball Joint Mechanism

As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility it the mounting hole pattern does not comply with the international VESA standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 29.08.07©

Adjust Donut Clamps

Mount Displays

DCable Management

100mm (4”)

75mm (3”)

100mm

(4”)

75mm

(3”)

LOOSEN

TIGHTEN

Adjust the Ball Joint

Mechanism to suit the

weight of your display.

Tighten or loosen

screws evenly with the

supplied 2.5mm Allen

Key, 1/4 turn at a time.

2.5mm

Allen Key

Cable

Balls

Cable

Clips

IMPORTANT:

When tightening the Donut

Clamp, each of the Donut

bolts must be tightened

evenly, as failure to do so will

damage the Donut Clamp.

Do not over tighten as this

may also result in damage.

Choose the correct Mounting Screws supplied in the bits

box and attach the display as shown.

Note: Extension

Clips are included

to suit VESA 100mm

x 100mm (4” x 4”)

Mounting Hole

Patterns.

Follow steps below to adjust the position of Donut Clamps. Ensure the Cable Slots

in all the Poles are facing to the rear.

LOOSEN

POSITION

TIGHTEN

C.1.

Loosen Donut Bolts evenly

using the supplied 5mm

Allen Key

C.2.

Slide the Donut Clamp to

desired position

C.3.

Tighten Donut Bolts firmly

using the supplied 5mm

Allen Key

Note: Ensure enough

slack is left in cables to

allow for movement.

Insert display cables into the slots in each pole, using

Cable Balls to hold them in place.

Note: When the slot in each pole cannot be used, use

the supplied Cable Clip’s to secure the display cables.

Table of contents

Other Atdec Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 