Atdec VFS-DV User manual

VFS-DV Page 1 of 4

Installation Guide

VFS-DV

COMPONENT CHECKLIST

VESA

Plate

(x2)

Quickshift

Donut

(x2)

Upright

Pole

(x1)

Base

(x1)

(Optional)

Security

Screw

(x2)

Cable Ball

(x4)

3/5mm

Allen Key

(x1 each)

M8x50mm

Screw (x1)

Mounting

Screw

M4x16mm

(x8)

Mounting

Screw

M4x12mm

(x8)

Mounting

Screw

M4x10mm

(x8)

Cable Clip

(x3)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs)

! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.

! The manufacturer accepts no responsibility for incorrect installation.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can

exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact

Atdec if you would like further information.

Freestanding Dual Vertical

REQUIRED TOOLS

• Phillips Head Screwdriver

WEIGHT RANGE

Per Monitor

Flat Monitor

0 - 12kg

0 - 26.5lbs

Curved Monitor

0 - 12kg

0 - 26.5lbs

VFS-DV Page 2 of 4

2. Attach Quickshift Donuts to the Pole (Ensure the cable slot faces towards the rear)

2.1 Slide the Quickshift Donut

onto the Pole.

2.2 If the Quickshift Donut requires further

tightening use the supplied 5mm Allen key.

2.3 Close the lever to lock the Quickshift.

Donut in place.

Slot

Groove

Insert

TIGHTEN

LOOSEN CLOSE

3. Attach the VESA Plate to your monitor (Repeat steps 3 to 6 for each monitor)

NOTE: Be sure to select a screw

length that suits the monitor.

3.1 Check VESA mounting compatibility 3.2 Screw VESA Plate to back of

monitor using provided screws.

100mm

75mm

100mm 75mm

Top of

monitor

Too short Too long

1. Attach Upright Pole to Base

1.1 Attach the Upright Pole to the

Base as shown below. Ensure the

Cable Slot faces towards the rear. OPTIONAL

BOLT THROUGH &

GROMMET MOUNT

Mount can also be bolted

through work surface or

grommet hole with the Atdec

Grommet Clamp (AC-GC),

sold separately.

Cable Slot

USER

BACK

TIGHTEN

FIRMLY

Upright Pole

M8x50mm Screw

5mm Allen Key

VFS-DV Page 3 of 4

5. Adjust the Height of the Quickshift Donut

5.1 Open the lever to loosen the Quickshift Donut. 5.2 Slide the Quickshift Donut to desired position.

5.3 If necessary, adjust the tension between the Donut

and the Pole using the 5mm Allen Key supplied.

5.4 Close the lever to lock the Quickshift Donut in place.

OPEN

LOOSEN

TIGHTEN

HOOK

Back of Display

PUSH

Release

Button

Phillips-head

Screwdriver

Security

Screw

TIGHTEN

4. Attach your Display to the Quickshift Donut

4.1 Hook the top of the VESA plate

onto the Quickshift Mount.

4.2 Press and hold the Release

Buttons. Gently push bottom of VESA

Plate into Quickshift Mount. Release

Buttons to lock in place.

4.3 (Optional) Insert the Security

Screw, and tighten using a Phillips-head

Screwdriver.

VFS-DV Page 4 of 4

Cable

Balls

(x2)

Cable

Clips

(x2)

7. Cable Management

Connect cables to your Displays,

routing them down to the rear of

the poles.

Push the cables into the slots, using

either the Cable Balls or Cable Clips

to secure them to the pole as shown.

Note: Ensure enough slack is left in

cables to allow for movement. When

the slot in each pole cannot be used,

use the supplied Cable Clips to

secure the cables.

6. Adjust the ball joint tension

6.1 If the monitors are not holding

position or are stiff to move, adjust

the tension plate by tightening or

loosening the three screws.

Note: Adjust 3

screws evenly in

small increments

Note: Support the monitor

while making adjustments.

3mm

Allen Key

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Other Atdec Rack & Stand manuals

Atdec

Atdec AWMS-2-BT75-FS User manual

Atdec

Atdec AWM-BT User manual

Atdec

Atdec TELEHOOK TH-3060-UT User manual

Atdec

Atdec SPACEDEC ACROBAT Operation instructions

Atdec

Atdec AWMS-DW6 User manual

Atdec

Atdec Spacedec Acrobat Swing Arm Double User manual

Atdec

Atdec TH-PFK User manual

Atdec

Atdec Visidec Freestanding Double User manual

Atdec

Atdec AWM-A13 User manual

Atdec

Atdec AWM-LC User manual

Atdec

Atdec VFS-DH User manual

Atdec

Atdec AWM-A13 User manual

Atdec

Atdec ADBS-3x1-30TW User manual

Atdec

Atdec SYSTEMA SW6S User manual

Atdec

Atdec ADBS-2x2-17MFB User manual

Atdec

Atdec VISIDEC FOCUS ARTICULATED ARM DOUBLE Operation instructions

Atdec

Atdec AWM-P G User manual

Atdec

Atdec Levitate L-PB User manual

Atdec

Atdec AWM Series User manual

Atdec

Atdec AWMS-2-BT75-G User manual

Atdec

Atdec Visidec Focus Articulated Arm Wall Operation instructions

Atdec

Atdec Visidec Focus Micro User manual

Atdec

Atdec APA-B User manual

Atdec

Atdec AF-M User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 