Atdec A-STSWW-A User manual

A-STSWW-A Page 1 of 5

Installation Instructions

Wall Mounted

Sit-to-Stand Workstation - Antimicrobial

Component Checklist

Step 1. Check Components

ABC D E

Lower Arm Upper Arm Vertical Screen

Slider Keyboard Tray Tilt Head

A-STSWW-A

• 8mm wrench

• Drill

• 10mm masonry bit

• 4.5mm drill bit

• Ratchet

• Spirit Level

• Stud Finder

• Pencil

5mm Allen 6mm Allen2.5mm Allen

M6X8 (x1) M4x10 (x4)M6X12 (x4)M8X20 (x1)

8mm

¼” Drive

Velcro

Strip (x2)

H J K L M N

PO Q R S T

Tools Required

Plastic

Washer (x1)

Coach

Screw (x6) Nylon

Anchor (x6)

Metal

Washer (x1)

M6X10 (x3)

Hardware

Wall Mounting Hardware

Check that you have received all parts against the Component Checklist.

! IMPORTANT - Install as per Installation Instructions

! The manufacturer accepts no responsibility for incorrect installation.

! This product supports a maximum load 8Kg (17.6lbs.)

! The wall mount can be installed on vertical, at, solid concrete or brick walls, or timber stud walls only.

! Thewallshouldbestrongenoughtosustainaweightofatleastfourtimesthatofthedisplayandwallmountbracketcombined.

If in doubt, consult a structural engineer.

! Checkwallanchorsandscrewsevery3monthsfromthetimeofinstallationtoensuretheworkstationisrmlyxedtothewall.

! Tighten all screws (do not exert excessive force to avoid breaking the screws or damaging their thread)

IMPORTANT INFORMATION

A-STSWW-A Page 2 of 5

2.3

2.4

2.5

Wall Plate

Remove top and

bottom covers from

the wall plate.

Push nylon

anchors into

each hole.

Fix wall plate to

the wall using 6

coach screws

10mm

55mm

Wall 2.1

2.2

Spirit

Level

2.3

2.4

Wall Plate

Remove top and

bottom covers from

the wall plate.

Fix wall plate to

the wall using 4

coach screws

4.5mm

55mm

Stud

2.2

2.1

Spirit

Level

Step 2. Option B - Stud wall installation

Tip: Screw in the top coach screw rst.

Usethesuppliedtemplate

to mark and drill 4 holes

into the wall.

Two people

required

Note: Use a stud nder to ensure

all holes are drilled into the stud.

Step 2. Option A - Masonry or cement wall installation

Tip: Screw in the top coach screw rst.

Usethesuppliedtemplate

to mark and drill 6 holes

into the wall.

Two people

required

Note: For optimum performance, use a spirit

level to ensure straight installation.

A-STSWW-A Page 3 of 5

5.1 Drop screw head into

keyhole slot in upper

arm plate.

5.2

Screw limits screen

rotation to 90°

Remove screw for

360° rotation

90°360°

5mm

Note: do not tighten screw ‘Q’

4.1 4.2

Step 4. Assemble slider to keyboard trayStep 3. Assemble upper arm

Step 5. Assemble slider to keyboard tray

Step 6. Attach tilting head to screen Step 7. Attach screen to arm Step 8. Replace covers

A-STSWW-A Page 4 of 5

Screen Height Tension

Tension Adjustment Points

Screen Tilt Tension

+35°

-5°

90°

+65°

-30°

Keyboard Tray Storage

Mouse Tray PositionArm Height Tension

Arm Rotation Joint Tension

Adjusting

Note: Arm must be

in highest position

to access tension

adjustment point.

Note: Supplied velcro strips secure

the keyboard when stowed.

The keyboard tray can be

folded away for storage.

Themousetraycanbepositioned on

the left or right of the keyboard tray.

A-STSWW-A Page 5 of 5

Wash parts in

warm soapy

water.

Push in tab to

remove mouse

tray.

• Detach lower arm cable

cover by removing 6 screws.

• Route cables through the

cavity in the arm, then

reattach the cover.

Note: Ensure there is sucient slack in the cables to

accommodate the workstation’s range of movement.

The upper arm cable

cover is detached by

pulling near the top of

the cover.

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

atdec.com

Cable Management. Route cables through arm.

Secure Keyboard Attach velcro to keyboard and tray Cleaning

Wrist pad and mouse tray can

be removed for cleaning.

Stud Wall

Drilling Template

Only drill holes marked with an ‘X’

Masonry Wall

Drilling Template

Only drill holes marked with an ‘X’

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 