Atdec AWM-LTH User manual

AWM-LTH Page 1 of 2

Installation Guide

AWM-LTH

Heavy Duty VESA Tilt Head

COMPONENT CHECKLIST

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! Curvedmonitors,deepdevices(suchasall-in-onePCs)andosetVESAlocationsexertadditionalleveragethatcanexceedthe

capacityofthemounteventhoughthemonitorweightmaybewithinthestatedrange.

! Themanufactureracceptsnoresponsibilityforincorrectinstallation.

! ThisproductiscompatiblewithAWMSeriesmonitorarmproducts.

Monitorweightshouldbe

withintheweightrangeof

all modular elements that

make up the complete

monitormountingsolution.

REQUIRED TOOLS

• Phillips Head Screwdriver

A

Heavy Duty

Tilt Head

(x1)

B

Screw

M4x25mm

(x4)

C

Screw

M4x16mm

(x4)

D

Screw

M4x12mm

(x4)

E

Spacer

(x4)

F

4mm

allen key

(x1)

WEIGHT RANGE

0 - 18kg

(0 - 40lb)

AWM-LTH Page 2 of 2

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

reserves the right to alter specifications without notice. ©20190121

1. Attach VESA head to monitor

1.2Ensuresuitablescrewsizeisused. 1.3VESAmountingcompatibility

Note: Forothersizes,useasuitable

adaptor plate

1.1ScrewtheVESAheadontomonitor

Note:Spacersmayberequiredfor

curved, recessed or uneven monitor

surfaces.

2. Mount monitor onto arm

3.1Usetheknobtotightenandloosenthe

tilttensiontosuityourmonitorweight.

Note:Alwayssupportthemonitor

whilstadjustingtopreventitfrom

fallingforwardsharply.

Tighten

Loosen

2.1 Push tilt head onto the shaft at the

endofthemonitorarm.

2.3 Tightenthejointscrewtosecure

thetiltheadandmonitorinplace.

3. Adjust tilt tension

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: Check the arm rotation

issmoothaftertightening.

2.2Ensuretiltheadisfullypushed

ontoshaft.

100mm

75mm

100mm

75mm

Flush

Too long Too short

Spacer

5mm 12mm

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 