Abus TVIP70000 User manual

32
TVIP70000/TVIP72000
User manual
Version12/2010
Translation of the original German operating manual. Keep safe for future reference!

Introduction
Dear customer,
Thank you for purchasing this product.
This product complies with current domestic and European regulations. Conformity has been proven,
and all related certifications are available from the manufacturer on request (www.abus-sc.com).
To maintain this status and to guarantee safe operation, it is your obligation to observe these operating
instructions!
Read the entire operating manual carefully before putting the product into operation and pay attention to all
operating and safety information!
All company names and product descriptions are trademarks of the corresponding owner. All rights
reserved.
In the event of questions, please contact your local maintenance specialist or dealer.
Disclaimer
These operating instructions have been produced with the greatest care. Should you discover any missing
information or inaccuracies, please contact us under the address shown on the back of the manual.
ABUS Security-Center GmbH does not accept any liability for technical and typographical errors, and
reserves the right to make changes to the product and operating instructions at any time and without prior
warning.
ABUS Security-Center GmbH is not liable or responsible for direct or indirect damages resulting from the
equipment, performance and use of this product. No forms of guarantee are accepted for the contents of this
document.

34
Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of
injury or health hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in these operating instructions
which must be observed.
This symbol indicates special tips and notes on the operation of the unit.
Important safety information
All guarantee claims become invalid for damages caused by non-compliance with these
operating instructions. We cannot be held liable for resulting damages.
We cannot be held liable in the event of material or personal damages caused by
improper operation or non-compliance with the safety information. All guarantee claims
are invalid in such cases.
The following safety information and hazard notes are not only intended to protect your health, but
also to protect the device from damage. Please read the following points carefully:
xThere are no components inside the product that require servicing. Dismantling the product also
invalidates the CE certification and guarantee claims/warranty.
xThe product can be damaged if it is dropped, even from a low height.
xThis device is designed for indoor use.
xInstall the device so that the image sensor is not subjected to direct sunlight. Pay attention to the
installation instructions in the corresponding chapter of these operating instructions.
Avoid the following adverse conditions during operation:
xMoisture or excess humidity
xExtreme heat or cold
xDirect sunlight
xDust or flammable gases, vapours or solvents
xStrong vibrations
xStrong magnetic fields (e.g. next to machines or loudspeakers)
xThe camera must not be installed on unstable surfaces
General safety information:
xDo not leave packaging material lying around. Plastic bags, sheeting, polystyrene packaging etc. can
pose a danger to children if played with.
xThe surveillance camera contains small parts which could be swallowed, and should be kept out of
reach of children for safety reasons.
xDo not insert any objects into the device through the openings.
xOnly use replacement devices and accessories that are approved by the manufacturer. Do not
connect any non-compatible products.
xPlease pay attention to the safety information and operating instructions for the other connected
devices.
xCheck the device for damage before commissioning. Do not put the device into operation if damages
are detected.
xAdhere to the operating voltage limits specified in the technical data. Higher voltages could destroy
the device and pose a health risk (electric shock).

35
Safety information
1. Power supply: Power supply unit – 100-240 VAC, 50/60 Hz /12VDC, 1 A (included in delivery)
Only operate this device through a power source which supplies the mains power specified on the type
plate. If you are unsure of the power supply at the installation location, contact your power supply
company. Disconnect the device from the mains power supply before carrying out maintenance or
installation work.
2. Overloading
Avoid overloading of mains sockets, extension cables and adapters as this can result in fires or electric
shocks.
3. Cleaning
Only use a damp cloth to clean the device. Do not use corrosive cleaning materials.
Disconnect the device from the mains power supply while doing this.
Warnings
Observe all safety and operating instructions before putting the device into operation for the first time.
1. Observe the following information to avoid damage to the mains cable and plug:
xDo not modify or manipulate the mains cable or plug.
xDo not bend or twist the mains cable.
xDo not pull the cable when disconnecting the device from the mains power – always take hold of
the plug.
xEnsure that the mains cable is positioned as far away as possible from any heating equipment,
as this could otherwise melt the plastic coating.
2. Follow these instructions at all times. Non-compliance to the instructions could cause an electric shock:
xDo not insert any metallic or flammable objects into the device.
xUse overvoltage protection to prevent damage caused by overvoltage (e.g. electrical storms).
3. Disconnect defective devices from the mains power immediately and contact your specialist dealer.
When installing the device in an existing video surveillance system, ensure that all devices are
disconnected from the mains power supply and low-voltage circuit.
If in doubt, have a specialist technician carry out assembly, installation and connection of the
device. Improper or unprofessional work on the mains power supply or domestic installation
puts both you and other persons at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run
separately from each other. They should not be connected at any point or become connected
as a result of a malfunction.
Unpacking the device
Handle the device with extreme care when unpacking it.
If the original packaging has been damaged, inspect the device. If the device shows signs of
damage, then return it in the original packaging and contact the delivery service.

36
Contents
1.Intended use .........................................................................................................................................37
2.Scope of delivery..................................................................................................................................37
3.Installation.............................................................................................................................................38
3.1Power supply........................................................................................................................................38
3.2Installing the camera............................................................................................................................38
4.Camera description..............................................................................................................................39
4.1Exterior view.........................................................................................................................................39
4.2Interior view ..........................................................................................................................................39
4.3Aligning the camera module...............................................................................................................40
4.4Description of the status LEDs...........................................................................................................40
4.5Description of the reset button function............................................................................................40
4.6Putting into operation..........................................................................................................................41
4.7Accessing the network camera for the first time..............................................................................42
4.8Accessing the network camera over a web browser........................................................................43
4.9Installing the ActiveX plug-in..............................................................................................................43
4.10Adjusting the security settings...........................................................................................................43
4.11Password prompt.................................................................................................................................44
4.12Accessing the network camera over an RTSP player ......................................................................44
4.13Accessing the network camera over a mobile phone ......................................................................45
4.14Accessing the network camera over Eytron VMS.............................................................................46
5.User functions ......................................................................................................................................47
5.1Live image.............................................................................................................................................47
5.2Camera control.....................................................................................................................................47
5.3Audio/video control..............................................................................................................................49
6.Camera settings (configuration).........................................................................................................50
6.1System...................................................................................................................................................50
6.2Camera ..................................................................................................................................................51
6.3Network .................................................................................................................................................52
6.4Schedule................................................................................................................................................56
6.5Security .................................................................................................................................................56
6.6Maintenance..........................................................................................................................................57
7.Maintenance and cleaning...................................................................................................................58
7.1Function test.........................................................................................................................................58
7.2Cleaning ................................................................................................................................................58
8.Disposal.................................................................................................................................................58
9.Technical data.......................................................................................................................................59

37
1. Intended use
The network camera is equipped with a high-quality image sensor. It is used for indoor video surveillance.
The product must not be exposed to moisture. The video surveillance camera is only designed
for use in dry rooms.
Use of this product for other than the described purpose may lead to damage to the product
and other dangers. All other uses are not in accordance with regulations, and result in the
invalidation of the product guarantee and warranty. No liability can be accepted as a result.
This also applies to any alterations or modifications made to the product.
Read the entire operating manual carefully before putting the product into operation. The
operating manual contains important information on installation and operation.
2. Scope of delivery
ABUS network camera
TVIP70000/TVIP72000
Power supply unit
Quickstart manual
1 metre network cable
Software CD
(including operating manual on CD)

38
3. Installation
Make sure that all accessories and articles listed above are present in the scope of delivery. An Ethernet
cable is required for camera operation. This Ethernet cable must meet the specifications of UTP Category 5
(CAT 5) and must not be longer than 100 meters.
3.1Power supply
Before starting installation, ensure that the mains voltage and the rated voltage on the camera are identical.
3.2Installing the camera
Firstly, undo the four screws to remove the dome
cover (see diagram on right, items 1 to 4).
The camera base plate is attached to the wall or
ceiling using two screws.
Ensure that the lens is directed towards the
area to be monitored.
Hold the camera in the desired position, mark both
holes on the surface, then drill the two holes. The
installation material is included in the scope of
delivery.
Cables can be laid at the side or through the ceiling
or wall. A break-out panel for feeding the cable is
located on the side of the housing if the cables are
laid at the side. This panel must be carefully
removed using pliers. Any remaining sharp edges
on the housing must be smoothed using a file.
Use the installation material provided (see diagram
on right, items 5 and 6) to fasten the camera in
place.
IMPORTANT!
The camera must be disconnected from the mains power during installation.
1
2
3
4
56

39
4. Camera description
4.1Exterior view
1– Network connection (Ethernet), RJ45
2– Power supply, 12 VDC, 5.5 x 2.1 mm
circular connector
4.2Interior view
3– Reset button
4– Status LEDs (P, S & L)
5– Lens
6– Camera module
7– Fixing screws for camera module
1
2
7
3
4
5
6
7
4

40
4.3Aligning the camera module
Loosen one of the two screws to the left or right of
the camera module (see diagram on right, item 7).
Use the tool provided to do this (hexagon wrench).
You can now align the spherical camera module
vertically and (slightly) horizontally by inserting the
tool in the opening on the top of the camera module
(see diagram on right, item 8).
Retighten the fixing screw.
4.4Description of the status LEDs
LED State Description
P – LED for displaying the
operating voltage Constantly red Power supply active
S & L – Network status S lights up orange, L flashes green
(at irregular intervals) Network status is OK, IP assigned
correctly
S & L – Network status Both LEDs inactive Disconnected from network
4.5Description of the reset button function
Function Description
To reset the camera to factory settings, press the
reset button on the camera. Then disconnect the
power supply to the camera but still hold the reset
button.
Now reconnect the power supply.
After 10 seconds release the reset button.
Now the camera is reseted to factory defaults.
Camera reset to the factory settings.
7
5
68
7

41
4.6Putting into operation
The network camera automatically detects whether a direct connection between the PC and camera should
be made. A cross-over network cable is not required for this. You can use the supplied patch cable for direct
connection when putting into operation for the first time.
Direct connection of the network camera to a PC/laptop
1. Ensure that a CAT 5 network cable is used.
2. Connect the cable to the Ethernet interface of the PC/laptop and the network camera.
3. Connect the power supply to the network camera.
4. Configure the network interface of your PC/laptop to the IP address 192.168.0.2 and the default
gateway to 192.168.0.1.
5. Go to point 4.7 to finish the initial set-up and establish the connection to the network camera.
Connecting the network camera to a router/switch
1. Ensure that a CAT 5 network cable is used.
2. Connect the PC/laptop to the router/switch.
3. Connect the network camera to the router/switch.
4. Connect the power supply to the network camera.
5. If a DHCP server is available in your network, set the network interface of your PC/laptop to
“Obtain an IP address automatically”.
6. If no DHCP server is available, configure the network interface of your PC/laptop to 192.168.0.2
and the default gateway to 192.168.0.1.
7. Go to point 4.7 to finish the initial set-up and establish the connection to the network camera.
cCAT 5 Ethernet cable
Internet
Other manuals for TVIP70000
1
This manual suits for next models
1
Table of contents
Other Abus IP Camera manuals

Abus
Abus TVHD60000 User manual

Abus
Abus TVIP62000 User manual

Abus
Abus TVIP41560 User manual

Abus
Abus PPIC90000 User manual

Abus
Abus TVIP21502 User manual

Abus
Abus TVIP21502 User manual

Abus
Abus IPCB42500 User manual

Abus
Abus TVAC19000A User manual

Abus
Abus eyseo TV7144 User manual

Abus
Abus TVAC19100A User manual

Abus
Abus TVVR11000 User manual

Abus
Abus TVAC15000 User manual

Abus
Abus TVIP71501 User manual

Abus
Abus TVIP51500 User manual

Abus
Abus TVIP52502 User manual

Abus
Abus PPIC90000 User manual

Abus
Abus TVIP11561 User manual

Abus
Abus TVAC16010B User manual

Abus
Abus TVHD50000 User manual

Abus
Abus TVAC16010C User manual

















