Vibraon Measurement Instruments
8
6 Screen descriptions
6.1 Analysis measurement screen
In the analysis screen you are able to see the total value as well as the amplitude and
frequencyofthevehighestpeaksinthespectrumrange.Ifyouhaveenabledthe
audio(seeaudioscreen)youmayalsoatthesametimelistentothebearings.
In the upper right corner you will see the battery status and if the charger is plugged
in or not.
Measurement status can be one of following:
- Measuring(Vibrationmeasuringisongoing)
- Autoranging(Theinstrumentiscalculatingthebestmeasurementlevelrange)
- Averaging(Averagingofthemeasureddata)
- OK(Themeasurementisstable)
-Overow (The signal is too high – the measurement is incorrect/not readable.)
Incaseofamplitudeoutofrange,thevalueisshownas3stars(***).
Whenthemeasurementisstable,thelastmessagelineshowsOK.
5
1Analysis measurement screen
In the analysis screen you are able to see the total value as well as the amplitude and frequency of the five first peaks
in the spectrum range. If you have enabled the audio (see audio screen) you may also at the same time listen to the
bearings.
In the upper right corner you will see the battery status and if the charger is plugged in or not.
Measurement status can be one of following:
- Measuring (Vibration measuring is ongoing)
- Ranging (The instrument is calculating the best measurement range)
- Averaging (Averaging of the measured data)
- OK (The measurement is stable)
- Overflow (The signal is too high –the measurement is incorrect/not readable.)
In case of amplitude out of range, the value is shown as 3 stars (***).
When the measurement is stable, the last message line shows OK.
The Frequency range of the peaks in relation to the frequency range setting is described in the below table, the limit
of the maximum frequency of the peak is 1 000 Hz or 60 000 CPM.
Frequency range of the peaks
When pressing the (UP) or (DOWN) arrow keys, in the Vibration Screen, the measuring unit is temporarily
changed.
When the (MENU) key is pressed, the Analysis Settings menu is shown.
Select an item with the (UP) and (DOWN) arrow keys.
Change the settings of the selected item with the (LEFT) and (RIGHT) arrow keys.
To exit Settingsmenu, just press again the (MENU) key.
All settings, except disabled transducer power, will be stored into the permanent FRAM memory.
NOTE: As default, when the instrument starts, the transducer power is ENABLED.
Total value
measurements
presentat
Measurement Stability bar
Indicates battery status and if it is charging
5
1Analysis measurement screen
In the analysis screen you are able to see the total value as well as the amplitude and frequency of the five first peaks
in the spectrum range. If you have enabled the audio (see audio screen) you may also at the same time listen to the
bearings.
In the upper right corner you will see the battery status and if the charger is plugged in or not.
Measurement status can be one of following:
- Measuring (Vibration measuring is ongoing)
- Ranging (The instrument is calculating the best measurement range)
- Averaging (Averaging of the measured data)
- OK (The measurement is stable)
- Overflow (The signal is too high –the measurement is incorrect/not readable.)
In case of amplitude out of range, the value is shown as 3 stars (***).
When the measurement is stable, the last message line shows OK.
The Frequency range of the peaks in relation to the frequency range setting is described in the below table, the limit
of the maximum frequency of the peak is 1 000 Hz or 60 000 CPM.
Frequency range of the peaks
When pressing the (UP) or (DOWN) arrow keys, in the Vibration Screen, the measuring unit is temporarily
changed.
When the (MENU) key is pressed, the Analysis Settings menu is shown.
Select an item with the (UP) and (DOWN) arrow keys.
Change the settings of the selected item with the (LEFT) and (RIGHT) arrow keys.
To exit Settingsmenu, just press again the (MENU) key.
All settings, except disabled transducer power, will be stored into the permanent FRAM memory.
NOTE: As default, when the instrument starts, the transducer power is ENABLED.
Total value
measurements
presentat
Measurement Stability bar
Indicates battery status and if it is charging
Indicates battery status and if it is charging
Total value
Measurment Stability bar
Frequency range
Peak number
Amplitude
Frequency /RPM
Measurment status
If alarm is activated levels will be displayed if not **** are displayed
