Vivo STAND-V104F User manual

Quad Monitor Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v104f

SKU: STAND-V104F

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

a (x1)

Pole

b(x1)

Base

c(x1)

Decorative

Cover

d1 (x1)

Center

Monitor Arm

d3 (x1)

Mount

e(x4)

Monitor Arm

Cover

f (x4)

Pad

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

d2 (x2)

Monitor Arm

h(x3)

M6x29

i(x4)

M8x10

j (x16)

M4x12

Thumbscrew

g(x2)

M10x47

k (x16)

M4x30

m(x2)

Spare Cap

l(x16)

M4 Spacer

n(x1)

Allen Wrench Set

o (x1)

Wrench

p1 (x2)

Side

VESA Plate

q1 (x2)

Nut

p2 (x2)

Center

VESA Plate

q2 (x2)

M4x6

r(x4)

Wire Clip

ASSEMBLY STEPS

TOOLS NEEDED

22lbs

(9.98kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

STEP 1

Install the pole (a) to the base (b) using M6x29 bolts (h). Tighten with a Phillips screwdriver and

install decorative cover (c).

PER MONITOR

STEP 2

Assemble the monitor arms (d1, d2) by placing plastic pads (f) on the top and bottom of arms (d2)

and inserting them into the center arm (d1) as shown in the diagram. Secure with M10x47 Bolts (g)

and tighten with the large Allen wrench (n). Press monitor arm covers (e) onto the top and bottom of

arm joints.

Carefully slide assembled monitor arm

(d1) and mount (d3) down onto the pole,

making sure holes for wire clips are facing

down, and secure with M8x10 bolts (i)

using the medium Allen wrench (n). Attach

the wire clips (r) to the monitor arm.

STEP 4

OPTION A: Flat Back Monitor

Attach the VESA plates (p1, p2) to the monitors using M4x12 thumb bolts (j).

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

STEP 3

OPTION B: Curved/Recessed Back Monitor

Attach the VESA plates (p1, p2) to the monitors using M4 spacers (l) and M4x30 bolts (k). Tighten with

a Phillips screwdriver.

STEP 5

Slide the center monitors onto the heads of monitor arm and mount. Secure with the M4x6 bolts (q2)

and tighten with a Phillips screwdriver.

Pry o the plastic cover and tighten the nut on the side of the tilt joint with the wrench (o) to fix the tilt

angle of side monitors. Tighten the grub screw on the back of center monitor joint using the small Allen

wrench (n) to fix tilt angle of center monitor.

STEP 6

grub

screw

Fix the tilt angle

è O

ÇNI ÇO

è N

ÇNI Ç

Slide the side monitors onto the heads of monitor arm and install the security nuts (q1). Make sure

the security nuts are installed before you rotate the monitors.

d1, d2

STEP 7

To adjust center monitor height, turn the screw behind center monitor joint using the medium Allen

wrench (n). To level the side monitors, remove the security nut and turn the bolt with the small Allen

wrench (n) to raise or lower the monitor. Replace nut aer the adjustment.

STEP 8

Pry o the plastic cover and use the large Allen wrench (n) to adjust swivel joints if needed.

STEP 9

Manage cables using the wire clips (r). Remove the split cap from the pole and feed cables through,

pulling ends out from the opening in back. Replace the split cap when finished.

LAST UPDATED: 03/05/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 