Vivo DESK-V133E User manual

Black Electric Multi Motor Corner Desk Frame

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/desk-v133e

SKU: DESK-V133E

[email protected]om www.vivo-us.com 309-278-5303

J (x1)

Extension

Cord

If you do not understand these directions, or if you have any doubts about the safety of the installation,

please call a qualified technician. Check carefully to make sure there are no missing or defective parts.

Improper installation may cause damage or serious injury. Do not use this product for any purpose that is

not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage

or injury caused by improper mounting, incorrect assembly, or inappropriate use.

PACKAGE CONTENTS

WARNING!

ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC

SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.

• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.

• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR

SELLER TO REPLACE DAMAGED PARTS.

• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE

MADE CONTACT WITH LIQUIDS.

• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.

• OUTDOOR USE IS PROHIBITED.

A (x1)

Telescopic

Crossbar

D(x3)

Liing

Column

F(x1)

Corner Foot

S-A (x12)

M6x10 Bolt

S-B x10)

M6x16 Bolt

S-D (x2)

3/4" Screw

H (x1)

Control Unit

B (x1)

Extension

Crossbar

G(x1)

Fixing Plate

I(x1)

Power Cord

K (x1)

Cable Tray

E(x2)

Foot

C(x3)

Side Bracket

S-F (x4)

M4x5 Bolt

S-G x3)

Cable Clip

S-H (x16)

Anti-Vibration

Pad

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

L (x2)

Hook

S-I (x1)

Allen

Wrench

M (x1)

Control Panel

S-C x16)

7/8" Screw

S-E (x2)

M4x5 Flat Head

Bolt

Phillips

Screwdriver

TOOLS

NEEDED

330lbs

(149.69kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

Drill

Level

STEP 2

Place the side brackets (C) upside down on a flat surface, then place telescopic crossbar (A) and

extension crossbar (B) over the brackets as shown, making sure the screw posts on the brackets fit

into the holes in the crossbars. Place liing columns (D) on telescopic crossbar, and align the holes

on the end of the extension crossbar with the holes on the center liing column and telescopic

crossbar. Secure the extension crossbar using two M6x12 bolts (S-A) through the side and two M6x16

bolts (S-B) through the crossbar and corner liing column as shown. Secure liing columns with ten

M6x12 bolts (S-A). Attach third liing column to the assembled frame by using four M6x12 bolts (S-A).

Tighten all fourteen bolts with the Allen wrench (S-I).

Loosen all eight set screws

on the telescopic crossbar (A)

and all four set screws on the

extension crossbar (B) using

the Allen wrench (S-I).

STEP 3

STEP 6

STEP 5

STEP 4

Place tabletop upside down on the floor.

Place frame assembly upside down on

tabletop, and adjust the crossbars to the

appropriate length.

Tighten all set screws with the Allen wrench (S-I).

Drill 3/8" (10mm) deep pilot holes under the desktop with a 3/32" (or

3mm) drill bit, then remove the frame from the desktop.

Place the feet (E) on the side

columns as shown. Insert

M6x16 bolts (S-B) into the four

mounting holes on each foot and

tighten with Allen wrench (S-I).

Press the corner foot (F) onto the

corner column.

STEP 7

STEP 8

Attach the fixing plate (G) to the frame using M4x6

flat head bolts (S-E). Tighten screws with a Phillips

screwdriver.

Connect control panel (M), liing columns (D)

and power cord (I) to the control unit (H). If

needed, use the extension cord (J) to connect the

farthest liing column.

STEP 9

Slide the control unit (H) onto the fixing plate (G) as shown.

STEP 10

STEP 11

Fix the hooks (L) to the cable tray (K) with M4x6 bolts (S-F)

and tighten with a Phillips screwdriver. Hang the shelf onto

the frame as shown.

Tighten installed thumbscrews to secure the cable tray (K). Press anti-vibration pads (S-H) into

desktop mounting holes.

STEP 12

Attach the desktop with 7/8" screws (S-C) using a Phillips screwdriver. Place the control panel at the

desired location and mark drilling locations with a pencil. Drill 3/8" (10mm) deep pilot holes under the

desktop with a 5/64" (or 2mm) drill bit. Attach the control panel to the desktop with 3/4" screws (S-D)

using a Phillips screwdriver. Add cable clips (S-G) to organize.

STEP 13

Connect the power cable to a wall outlet to power on desk for operation. Each foot pad can be adjusted

independently for fine tuning. Slightly turn the foot pad to lower or raise the base. Use a level to ensure

the desktop is even.

CAUTION!

Failure to follow these instructions may result in property damage and/or personal injury.

Do not exceed desk weight limit. Keep area of vertical motion free of

obstacles.

Keep weight on desk balanced for

correct operation and longer life of

components.

Leave enough slack in cables to

allow for full range of vertical

motion.

LAST UPDATED: 09/18/2019

Open Monday-Friday from 7:00am-7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times.

If any parts are received damaged or defective, please contact us.

We are happy to replace parts to ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected]

www.vivo-us.com

309-278-5303

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

AVG. RESOLUTION TIME (within oice hrs): < 15 M

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 