Vivo STAND-V012F User manual

Dual Monitor Extra Tall Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v012f

[email protected]om www.vivo-us.com 1-800-371-5654

SKU: STAND-V012F

PACKAGE CONTENTS

WARNING!

a (x1)

Pole

b(x1)

Weighted Base

c(x1)

Swivel Arm

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

d(x2)

VESA Plate

e(x3)

M5x14

f (x2)

Nut

g (x1)

M10 Bolt

h (x1)

Support Plate

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

i(x1)

M10 Washer

j(x1)

Spring Washer

k (x1)

Grommet

Base Plate

l1 (x3)

Wire Clip

l2 (x4)

Wire Clip

m(x1)

Allen key

n (x1)

Wrench

o (x8)

M4x12

p (x8)

M4x30

q (x8)

M4 Spacer

r(x1)

So Pad

ASSEMBLY STEPS

STEP 1

TOOLS NEEDED

Phillips

Screwdriver

OPTION A: Clamp Installation

Install the Pole (a) to the Weighted base (b) using 3 M5x14 Bolts (e) and tighten using the Allen Key (m),

see Figure 1. Optionally, you can drill a 10mm diameter hole in your desk and secure using the Support

Plate (h), M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10 Bolt with provided

Wrench (n), See figure 2.

STEP 2

Remove the grub screws from poles (a) using the small Allen Key (m). Connect the poles by threads.

Install grub screws and fasten them by provided Allen Key (m).

Figure 2

Figure 1

22 lbs

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

Drill

STEP 2 (Continued)

OPTION B: Grommet Base Installation

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before

installing the desk mount. Install the Grommet Base Plate (k) to the Pole (a) using 3pcs M5x14 Bolts

(e), and tighten using the Allen Key (m), see Figure 3. Attach So Pad (r) to the Grommet Base Plate

(k), see Figure 4. Position the Pole (a) on the mounting surface and secure using the Support Plate (h),

M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10 Bolt using provided Wrench (n),

see Figure 5.

OPTION C: Self-Drilled Grommet Base Installation

Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm) diameter

hole at the marked position through the mounting surface. Install the Grommet Base Plate (k) to the

Pole (a) using 3pcs M5x14 Bolts (e), and tighten using the Allen Key (m), see Figure 6. Attach So Pad

(r) to the Grommet Base Plate (k), see Figure 7. Position the Pole (a) on the mounting surface and

secure using the Support Plate (h), M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10

Bolt using provided Wrench (n), see Figure 8.

Figure 3

Figure 5

rFigure 4

Figure 6

Figure 8

rFigure 7

STEP 3

Install Swivel Arm (c) to the Pole (a). Fasten the bolt with supplied Allen Key (m). Attach the Wire Clip

(l1,l2) to the Pole (a) and Swivel Arm (c).

STEP 4

OPTION A: Flat Back Monitor

Attach VESA Plate (d) to back of monitor using

bolts (o).

OPTION B: Curved Back Monitor

Attach VESA Plate (d) to back of monitor using

bolts (p) and spacers (q).

STEP 5

Slide the monitor onto the head of Swivel Arm (c). Install the security Nut (f). Make sure the security

nut is installed before you rotate the monitor.

STEP 6

Tighten the bolt with the supplied Allen Key (m) to fix the tilt angle. If one monitor is lower, remove

the Nut (f) and turn the bolt counter-clockwise with the Allen Key (m) to raise the monitor. Replace

Nut (f) aer the adjustment.

Fix the tilt angle

Ignore this step if

monitors are level

STEP 7

Use the supplied Allen Key (m) to make any necessary adjustments.

Manage the wires and store the Allen keys (m) in the Wire Clip (l1) for future use.

Last Updated: 08/30/2019

If any parts are received damaged or defective, please contact us. We are happy to

replace parts to ensure you have a fully functioning product.

For more VIVO products, check out our website at:

www.vivo-us.com.

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected]om www.vivo-us.com 1-800-371-5654

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 