Vivo MOUNT-UPS01 User manual

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

Universal Under Desk and Wall UPS Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/mount-ups01

SKU: MOUNT-UPS01

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2

TOOLS NEEDED

33lbs

(15kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do

not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly

or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

NOTE: SOME HARDWARE MAY NOT BE USED

PACKAGE CONTENTS

A (x1)

Mount

B(x4)

ST4.2x35mm

Screw

C (x4)

ST4.8x19mm

Screw

G (x1)

Wrench

D (x4)

Drywall

Anchor

E(x4)

Concrete

Anchor

F (x4)

Washer

Level Phillips

Screwdriver Drill

ASSEMBLY STEPS

STEP 1

Loosen the four nuts on the mount (A) using the wrench (G). Adjust the mount and slide in

the UPS.

3

STEP 2

Adjust the mount horizontally to where the brackets won’t interfere with any buttons or

cords. Adjust the mount vertically so the UPS is snug but still able to be removed. This will

be re-tightened in a later step.

NOTE: Due to the variability of UPS’s, some outlet ports may be blocked by the brackets.

Adjust horizontally as needed to allow for the most ports to be available.

STEP 3

Tighten the four nuts on the mount to lock its current position. Then remove the UPS from

the mount

4

STEP 4

Place the mount (A) against the mounting location and mark drilling locations with a

pencil. If mounting to a wood stud wall, use of a stud finder is recommended.

STEP 5

Remove the screws from the sides of the mount (A), and separate into the screws (A1),

brackets (A2) and mount (A3).

5

OPTION B: Wood Stud Wall Installation

Using marked locations, drill 1.6” (40mm) deep holes using a 1/8” (3mm) drill bit. Mount

the brackets (A2) to the wall using ST4.2x35mm screws (B) with washers (F).

NOTE: If only one bracket aligns with a stud, refer to “Option C: Drywall Installation” for the

other bracket.

STEP 6

1/8”

OPTION A: Under Desk Installation

Using marked locations, drill 3/8” (10mm) deep holes using a 1/8” (3mm) drill bit. Mount

the brackets (A2) to the desk using ST4.8x19mm screws (C).

6

OPTION C: Drywall Installation

Using a Phillips screwdriver, screw drywall anchors (D) into marked locations

(the anchors are self tapping and do not require pre-drilling the wall). Mount the

brackets (A2) to the wall using ST4.2x35mm screws (B) with washers (F).

OPTION D: Concrete/Brick Wall Installation

Using marked locations, drill 1.6” (40mm) deep holes using a 15/64” (6mm) drill bit.

Press the concrete anchors (E) into the holes and mount the brackets (A2) to the

wall using ST4.2x35mm screws (B) with washers (F).

15/64”

STEP 6 (Continued)

7

Slide the mount (A3) onto the brackets (A2) and secure using screws (A1).

FOR OPTION B, C, D

FOR OPTION A

STEP 7

Loosen the two nuts on each support and re-insert the UPS into the mount. Push the

supports against the UPS and tighten down the nuts. Unlock the buckle on each strap,

tighten the straps around the UPS, and lock the buckle to secure.

STEP 8

LAST UPDATED: 08/10/2020

REV1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303