Vivo STAND-V101G2 User manual

Pneumatic Arm Dual Monitor Desk Mount with Pull Handle

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v101g2

SKU: STAND-V101G2

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

A (x1)

Base

B(x1)

Lower Arm

C(x1)

Gas Spring Arm

P (x1)

3mm Allen

Wrench

L (x1)

Clamp

M (x4)

M6x12 Flat

Head Bolt

N (x4)

M6x10 Bolt

O (x2)

M6x22 Bolt

M-A (x8)

M4x12

E(x2)

VESA Plate

G(x1)

Clamp Plate

H (x1)

Grommet

Plate

I(x1)

So Pad

J (x1)

Cover

K (x1)

Clamp

Brace

M-B (x8)

M5x12

M-C (x8)

D5 Washer

D(x1)

Monitor Arm

F (x1)

Handle

R (x1)

6mm Allen

Wrench

Q(x1)

4mm Allen

Wrench

ASSEMBLY STEPS

STEP 1

OPTION A: Clamp Installation

Attach clamp brace (K) to base (A) using M6x12 flat head bolts (M) and tighten with 4mm Allen

wrench (Q). Apply so pad (I) to underside of base. Install M6x10 bolts (N) to back of clamp (L),

leaving 6mm of thread exposed. For a desk thickness of 3/8” - 2-1/2” (10 - 58mm), hang assembled

clamp into top 4 slots of clamp brace, or for a desk thickness of 2” - 3-3/8” (50 - 85mm), into lower 4

slots. Tighten with 4mm Allen wrench (Q), then place clamp plate (G) on top of clamp bolts. Position

base on desktop and tighten clamp bolts evenly using 6mm Allen wrench (R). Attach cover (J) to

back of clamp brace.

TOOLS NEEDED

Phillips

Screwdriver

2.2-17.6lbs

(1-8kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

STEP 1 (Continued)

Attach grommet plate (H) to base

(A) using M6x12 flat head bolts (M)

and tighten with 4mm Allen wrench

(Q). Apply so pad (I) to underside

of base. Position base over grommet

hole in desktop, or drill a 3/8” (10mm)

hole through the desk for installation.

Remove large bolt from clamp (L)

using 6mm Allen wrench (R), then

Insert clamp bolt with clamp plate

(G) up through the underside of the

desk and tighten using the 6mm Allen

wrench (R).

STEP 2

STEP 3

Place lower arm (B) on top of base, and secure by turning the lower screw in back with 3mm Allen

wrench (P). Optionally, also tighten the upper screw to restrict swivel movement to +/-90 degrees.

Place gas spring arm (C) on top of lower arm, and secure by turning the screw in back with 3mm Allen

wrench (P).

OPTION B: Grommet Base Installation

STEP 4

Install the VESA plates (G) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with

washers (M-C), making sure the large end of each bracket in back is facing up.

STEP 5

Mount handle (F) to back of monitor arm using M6x22 bolts (O) to one of the positions shown in the

diagram according to the size of your monitors. Tighten with 4mm Allen wrench (Q).

STEP 6

Install monitor arm (D) to gas spring arm using M6x12 bolts (N) and tighten with

4mm Allen wrench (Q).

STEP 7

Place the monitors with VESA plates into the supports on the arm, then turn

the screw on each support to secure the monitors.

STEP 8

If needed, adjust gas spring arm to support the monitors using the 6mm Allen wrench (R). While

holding arm in the straight forward position, turn the screw in back clockwise to decrease support,

and counter-clockwise to increase. Slightly loosen the monitor arm for leveling if needed.

STEP 9

Remove cable cover on upper arm using a Phillips screwdriver. Slide cable cover on lower

arm forward to remove.

STEP 10

For safety, please do not extend the monitors behind the desk. This may cause instability and tip the

desk over

STEP 12

Organize cables, then reinstall cable covers to arms.

STEP 11

Turn the screw underneath each monitor support bracket for leveling. Tools may be

stored in the cover (J).

LAST UPDATED: 04/08/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 