Smeg CS120A-6 User manual

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE_______________ 42

2. INSTALLATION OF THE APPLIANCE________________________ 44

3. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 47

4. FINAL OPERATIONS_____________________________________ 49

5. DESCRIPTION OF CONTROLS ____________________________ 51

6. USE OF THE COOKING HOB ______________________________ 58

7. USE OF THE OVENS_____________________________________ 59

8. ACCESSORIES _________________________________________ 61

9. COOKING HINTS________________________________________ 63

10. CLEANING AND MAINTENANCE ___________________________ 71

11. EXTRAORDINARY MAINTENANCE _________________________ 75

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE

USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER

USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, SWITCH OFF THE POWER

SUPPLY TO THE APPLIANCE AND CALL THE NEAREST TECHNICAL

ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE

THEY COULD CAUSE A FIRE IN THE HOME.

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND

BRAND NAME IS POSITIONED VISIBLY IN THE STORAGE COMPARTMENT.

THE PLATE MUST NOT BE REMOVED.

Introduction

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE COOKING HOB GRIDS.

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING

CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN

EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY

ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE

RESPONSIBLE FOR THEIR SAFETY.

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE

2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE).

THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF

RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance or by the use of non-original

spares.

Instructions for the installer

2. INSTALLATION OF THE APPLIANCE

It is the law that all gas appliances are installed by competent persons.

Corgi gas installers are approved to work to safe and satisfactory

standards. All gas installation, servicing and repair work must be in

accordance with the gas safety regulations 1984 (installation and use) as

amended 1990.

It can be placed against walls higher than the hob, at a distance of at

least 50 mm from the side of the appliance, as shown in the drawings A

and B relating to the installation classes. Wall units or extractor hoods

located above the hob must be at least 750 mm away from it.

SLOT IN FREE STANDING

2.1 Positioning and levelling of the appliance

The appliance is equipped with wheels and adjustable feet to simplify the

positioning procedure. To use the front wheels, screw in the foot as

shown here, so that the appliance rests on the front wheels. However, to

allow the appliance to be moved freely it must be lifted at the back. To

do this, proceed as follows:

use a 10 socket wrench to screw in

the 2 hex nuts underneath the oven

compartment: this raises the

appliance either to level it or to

allow it to be moved around.

Once all procedures are complete,

unscrew the front feet and the hex

nuts to set the cooker stable and

level.

2.2 Electrical connection

Make sure that the power line voltage matches the specifications

indicated on the rating plate located inside the storage compartment.

This rating plate must never be removed.

Instructions for the installer

The connection to the mains shall be done conforming to the regulations

in force. Check that the power line is adequately grounded. Do not use

reducers, adapters or shunts. On the power line, install an omnipolar cut-

off device with contact cut-off distance greater than or equal to 3 mm,

located in an easily accessible position near the unit.

The connection terminals are

located at the rear of the

appliance. For electrical

connections see following

diagram. To access, remove

the rear cover.

For operation on 380-415V3N

∼

:use

an H05RR-F-type five-core cable (5 x

1.5 mm2).

For operation on 380-415V2N

∼

:use

an H05RR-F-type four-core cable (4 x

2.5 mm2).

For operation on 220-240V

∼

:use an

H05RR-F-type three-core cable (3 x 4

mm2).

The cable end to be connected to the

appliance must be provided with an

ground wire (yellow-green) at least 20

mm longer.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance.

Instructions for the installer

2.3 Ventilation requirements

The room containing the appliance should have an air supply in accordance with

B.S. 5440 part 2 1989.

1. All rooms require an opening window or equivalent, and some rooms will

require a permanent vent as well.

2. For room volumes up to 5 m3an air vent of 100 cm2is required.

3. If the room has a door that opens directly to the outside, and the room

exceeds 1 m3no air vent is required.

4. For room volumes between 5 m3and 10 m3an air vent of 50 cm2is required.

5. If there are other fuel burning appliances in the same room B.S. 5440 part 2

1989 should be consulted to determine the air vent requirements.

6. This appliance must not be installed in a bed sitting room of less than 20 m3

or in a bathroom or shower room.

Windows and permanent vents should therefore not be blocked or removed

without first consulting a Corgi gas installer.

Failure to install appliances correctly is dangerous and could lead to

prosecution.

2.4Connecting to natural and LPG gas (Please see connection

diagram)

Make the connection to the appliance using flexible bayonet

style hose in accordance to B.S. 669. The hose connection at

the rear of the appliance has a 1/2" BSP internal thread.

Please use seal Cbetween the flexible connection Land the

appliance supply tube B. When making the connection, make

sure that no stress of any kind is applied to the cooker and

that the hose does not touch any sharp edges.

If connecting to LPG the bayonet hose must have red

bands on it.

2.5 Instruction for wall fixing (only on some models)

1) Fix the screw to the wall and hook the chain (B);

2) Hook the chain to the hole positioned at the rear of the cooker by the gas

pipe (A);

3) Once the chain is in position, push the cooker against the wall;

4) The height of the screw hole from floor level must not exceed 800 mm (C).

Instructions for the installer

3. ADAPTATION TO DIFFERENT TYPES OF GAS

Before performing any cleaning or maintenance work, switch off the

power supply to the appliance.

The cooking hob of the cooker is preset for G20 natural gas at a

pressure of 20 mbar. In the case of functioning with other types of gas the

burner nozzles must be changed and the minimum flame adjusted on the

gas taps. Replace the burner nozzles as indicated in the table of the gas

to be used.

3.1 Changing nozzles

1. Extract the grids and remove all the caps and flame-spreader

crowns;

2. unscrew the burner nozzles with a 7 mm socket wrench;

3. proceed with replacing the burner nozzles in accordance with the

table for the gas in question.

Instructions for the installer

3.2 Burner and nozzle characteristics table

Burner

Rated

heating

capacity

(kW)

LPG –G30/G31 28/37 mbar

(drawing ref. X238)

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

flowrate

(W)

Flowrate

g/h G30

Flowrate

g/h G31

Auxiliary 1.05 50 30 400 76 75

Semi rapid 1.8 65 33 500 131 129

Rapid 3.0 85 45 800 218 215

Fish Burner 1.9 68 45 800 138 136

Triple crown 4.0 100 65 1600 291 286

Burner

Rated

heating

capacity

(kW)

NATURAL GAS – G20 20 mbar

Nozzle diameter

1/100 mm

Drawing

Ref.

Reduced flowrate

(W)

Auxiliary 1.05 72 (X) 400

Semi rapid 1.8 97 (Z) 500

Rapid 3.0 115 (Y) 800

Fish Burner 1.9 94 (X) 800

Triple crown 4.0 135 (S) 1600

3.3 Arrangement of burners on cooking hob

BURNERS

1Auxiliary

2Semi rapid

3Rapid

4Triple crown

5Fish burner

Instructions for the installer

4. FINAL OPERATIONS

After replacing the nozzles, reposition the flame-spreader crowns, the

burner caps and the grids.

Following adjustment to a gas other than the preset one, replace the gas

adjustment label fixed to the appliance with the one corresponding to the

new gas. This label is in the packet together with the nozzles.

4.1 Adjustment of minimum for natural gas

Light the burner and turn it to the minimum

position . Extract the gas tap knob and turn the

adjustment screw at the side of the tap rod until

the correct minimum flame is achieved.

Replace the knob and check burner flame

stability: (rapidly turning the knob from maximum

to minimum position, the flame should not go

out). Repeat the operation on all the gas taps.

4.2 Regulation of minimum for LPG

For regulating the minimum with LPG, the screw at the side of the tap rod

must be turned clockwise all the way.

The bypass diameters for each individual burner are shown in paragraph

“3.2 Burner and nozzle characteristics table”. When adjustment is

complete, re-seal the by-passes using wax or an equivalent material.

Instructions for the installer

4.3 Mounting the rear top upstand

•Position the upstand above the top, taking care to align holes Awith

holes B.

•Secure the upstand to the top by tightening screws C.

This manual suits for next models

Table of contents

Popular Cooker manuals by other brands

Modena

Modena FC 7645 SGM User manual book

Electrolux

Electrolux Insight EKG6049 user manual

Stanley

Stanley Donard 60 Installation and operating instructions

Bartscher

Bartscher 201TC manual

Parkinson Cowan

Parkinson Cowan 50 GR/BU installation instructions

Siemens

Siemens HK9P00020U instruction manual

Creda

Creda S150E Installation and user instructions

Creda

Creda HB48309 instructions

Bosch

Bosch HCE743220F instruction manual

Tricity Bendix

Tricity Bendix SE545P manual

NEFF

NEFF E1461A2/01 Instructions for use

Zanussi

Zanussi ZCM 700 X Instruction booklet

RiverGrille

RiverGrille TF2002501-RG Assembly instruction

Vollrath

Vollrath 69504F Operator's manual

Tricity Bendix

Tricity Bendix CSIE500 Operating and installation instructions

AEG

AEG Competence 5731 V Instruction book

Euromaid

Euromaid ES60 Installation and operation manual

Hotpoint

Hotpoint HUI 62 TP Instructions for installation and use