Smeg A42-5 User manual

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE_____________________ 33

2. INSTALLATION OF THE APPLIANCE ______________________________ 35

3. ADAPTATION TO DIFFERENT TYPES OF GAS______________________ 38

4. FINAL OPERATIONS ___________________________________________ 40

5. DESCRIPTION OF CONTROLS___________________________________ 41

6. USE OF THE COOKING HOB ____________________________________ 47

7. USE OF THE OVENS ___________________________________________ 48

8. AVAILABLE ACCESSORIES _____________________________________ 49

9. COOKING HINTS ______________________________________________ 50

10. CLEANING AND MAINTENANCE _________________________________ 55

11. EXTRAORDINARY MAINTENANCE _______________________________ 58

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE

READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE

USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED.

INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN

ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS

INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT

REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY

OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD.

ALL OTHER USES ARE CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER

USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE

THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST

SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET

MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT

REGULATIONS.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN

BUILT IN.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW.

SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE

SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

(OFF) WHEN YOU FINISH USING THE HOB.

NEVER PUT INFLAMMABLE OBJECTS INTO AN OVEN: IF THEY CATCH FIRE

THEY COULD CAUSE A FIRE IN THE HOME.

Introduction

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND

BRAND NAME IS VISIBLY POSITIONED ON THE REAR PROTECTIVE COVER

OF THE APPLIANCE. A COPY OF THE PLATE IS INCLUDED WITH THE

HANDBOOK AND YOU ARE ADVISED TO FIX IT IN THE APPROPRIATE

SPACE ON THE INSIDE COVER PAGE.

THE PLATE MUST NEVER BE REMOVED.

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO

TOUCH THE HEATING ELEMENTS INSIDE THE OVEN.

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS

ON THE COOKING HOB GRIDS.

DO NOT INSTALL THIS APPLIANCE ON A RAISED PLATFORM

DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE

OUTER PERIMETER OF THE HOB.

THE OVEN DOORS ARE SPRUNG AND CLOSE VERY QUICKLY: TAKE CARE

NOT TO TRAP YOUR FINGERS.

THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW

CHILDREN TO GO NEAR OR PLAY WITH IT.

WHILE COOKING WITH THE OVEN DOOR OPEN, A GREAT DEAL OF HEAT

WILL COME OUT: KEEP CHILDREN AWAY FROM THE OVEN.

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE

2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE).

THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF

RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC

EQUIPMENT.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND

PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance or by the use of non-original

spares.

Instructions for the installer

2. INSTALLATION OFTHE APPLIANCE

It is the law that all gas appliances are installed by competent persons.

Corgi gas installers are approved to work to safe and satisfactory

standards. All gas installation, servicing and repair work must be in

accordance with the gas safety regulations 1984 (installation and use) as

amended 1990.

This unit is equipped with a type Y fire protection, and may be set

against walls that are higher than the hob.

2.1 Electrical connection

Check that the voltage and dimensioning of the supply line correspond to

the characteristics shown on the plate fixed to the rear protective cover

of the appliance.

This plate must never be removed.

If the appliance is hooked-up to the supply by means of a fixed

connection, install a multipolar cut-out device on the line, with contact

opening distance equal to or greater than 3 mm, located near the

appliance and in an easily reachable position.

Hook-up to the supply may be fixed or with plug and socket. In the latter

case the plug and socket must be suitable for the cable employed and

conform with the regulations in force. Regardless of the type of

connection, earthing of the appliance is absolutely obligatory. Before

connection make sure that the supply line is suitably earthed. Avoid the

use of reducers, adapters or shunts.

The manufacturer declines all responsibility for damage to persons

or things caused by non-observance of the above prescriptions or by

interference with any part of the appliance.

Instructions for the installer

Twin oven model

The appliance comes with a terminal board on the back for electrical

hook-up (see following diagram). To open the terminal board cover,

remove the fixing screw and raise the cover.

1 - For operation on 220-240V

∼

:use a

three-pole H05RR-F type cable (3 x 2.5

mm2). This is the connection carried out

in the factory.

2 - For operation on 220-240V3

∼

:use a

four-pole H05RR-F type cable (4 x 1.5

mm2).

3 - For operation on 380-415V2N

∼

:use a

four-pole H05RR-F type cable (4 x 1.5

mm2).

The cable end to be connected to the

appliance must be provided with an ground

wire (yellow-green) at least 20 mm longer.

Instructions for the installer

2.2 Ventilation requirements

The room containing the appliance should have an air supply in

accordance with B.S. 5440 part 2 1989.

1. All rooms require an opening window or equivalent, and some

rooms will require a permanent vent as well.

2. For room volumes up to 5 m3an air vent of 100 cm2is required.

3. If the room has a door that opens directly to the outside, and the

room exceeds 1 m3no air vent is required.

4. For room volumes between 5 m3and 10 m3an air vent of 50 cm2is

required.

5. If there are other fuel burning appliances in the same room B.S.

5440 part 2 1989 should be consulted to determine the air vent

requirements.

6. This appliance must not be installed in a bed sitting room of less

than 20 m3or in a bathroom or shower room.

Windows and permanent vents should therefore not be blocked or

removed without first consulting a Corgi gas installer.

Failure to install appliances correctly is dangerous and could lead

to prosecution.

The room must be kept adequately ventilated to remove the heat and

humidity produced by cooking; after prolonged use in particular, open a

window or increase the speed of any fans installed.

2.3 Connecting to natural and LPG gas

(Please see connection diagram)

Make the connection to the appliance using

flexible bayonet style hose in accordance to B.S.

669. The hose connection at the rear of the

appliance has a 1/2" BSP internal thread. Please

use seal Cbetween the flexible connection Land

the appliance supply tube B. When making the

connection, make sure that no stress of any kind

is applied to the cooker and that the hose does

not touch any sharp edges.

If connecting to LPG the bayonet hose must

have red bands on it.

When installation is complete, check for any

leaks with a soapy solution and never with a

naked flame.

Take care that the hose is not crushed or

damaged.

Instructions for the installer

3. ADAPTATIONTO DIFFERENTTYPES OF GAS

Before performing any cleaning or maintenance work, detach the

appliance from the electrical socket.

The cooking hob of the cooker is preset for G20 natural gas at a

pressure of 20 mbar. In the case of functioning with other types of gas the

burner nozzles must be changed and the minimum flame adjusted on the

gas taps. Replace the burner nozzles as indicated in the table of the gas

to be used.

3.1 Changing nozzles

1. Extract the grids and remove all the caps and flame-spreader

crowns;

2. unscrew the burner nozzles with a 7 mm socket wrench;

3. proceed with replacing the burner nozzles in accordance with the

table for the gas in question.

Instructions for the installer

3.2 Burner and nozzle characteristics table

Burner

Rated

heating

capacity

(kW)

LPG –G30/G31 28/37 mbar

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

flowrate

(W)

Flowrate

g/h G30

Flowrate

g/h G31

Auxiliary 1.05 50 30 360 76 75

Semi rapid 1.8 65 33 450 131 128

Rapid 3.0 85 45 750 218 214

Triple crown 3.3 91 68 1600 240 235

Burner

Rated

heating

capacity

(kW)

NATURAL GAS – G20 20 mbar

Nozzle diameter

1/100 mm

Reduced flowrate

(W)

Auxiliary 1.05 72 360

Semi rapid 1.8 97 450

Rapid 3.0 115 750

Triple crown 3.5 133 1600

3.3 Arrangement of burners on cooking hob

BURNERS

1Auxiliary

2Semi rapid

3Rapid

4Triple crown

Instructions for the installer

4. FINAL OPERATIONS

After replacing the nozzles, reposition the flame-spreader crowns, the

burner caps and the grids.

Following adjustment to a gas other than the preset one, replace the gas

adjustment label fixed to the appliance with the one corresponding to the

new gas. This label is in the packet together with the nozzles.

4.1 Adjustment of minimum for natural gas

Light the burner and turn it to the minimum

position . Extract the gas tap knob and turn the

adjustment screw at the side of the tap rod until

the correct minimum flame is achieved.

Replace the knob and check burner flame

stability: (rapidly turning the knob from maximum

to minimum position, the flame should not go

out). Repeat the operation on all the gas taps.

4.2 Regulation of minimum for LPG

For regulating the minimum with LPG, the screw at the side of the tap rod

must be turned clockwise all the way.

The bypass diameters for each individual burner are shown in paragraph

“3.2 Burner and nozzle characteristics table”. When adjustment is

complete, re-seal the by-passes using wax or an equivalent material.

4.3 Positioning and levelling of the appliance

Having carried out the electricity and gas hook-up, level the appliance

using the four adjustable legs.

Instructions for the user

5. DESCRIPTION OF CONTROLS

5.1 Front control panel

All the cooker controls and commands are on the front panel.

The user has only to press the central key for 1/2 seconds to enable use

of the oven on first use or after a power blackout.

DESCRIPTION OF SYMBOLS

FRONT RIGHT BURNER

MAIN OVEN

BACK RIGHT BURNER

AUXILIARY OVEN

GRILL

BACK LEFT BURNER

AUXILIARY OVEN

VARIABLE GRILL

FRONT LEFT BURNER

COOKING HOB BURNER COMMAND KNOB

The flame is lit by pressing the knob and turning it

anticlockwise to maximum flame . To adjust the

flame turn the knob between maximum ( ) and

minimum ( ). The burner goes out when the knob is

returned to the position .

MAIN OVEN THERMOSTAT KNOB

Selection of cooking temperature is carried out by

turning the knob clockwise to the required temperature,

between 50° and 250°C.

The tell-tale light comes on to indicate that the oven is

Warming up. When it goes out it means that the

required temperature has been reached.

This manual suits for next models

Table of contents

Popular Cooker manuals by other brands

Modena

Modena FC 7645 SGM User manual book

Electrolux

Electrolux Insight EKG6049 user manual

Stanley

Stanley Donard 60 Installation and operating instructions

Bartscher

Bartscher 201TC manual

Parkinson Cowan

Parkinson Cowan 50 GR/BU installation instructions

Siemens

Siemens HK9P00020U instruction manual

Creda

Creda S150E Installation and user instructions

Creda

Creda HB48309 instructions

Bosch

Bosch HCE743220F instruction manual

Tricity Bendix

Tricity Bendix SE545P manual

NEFF

NEFF E1461A2/01 Instructions for use

Zanussi

Zanussi ZCM 700 X Instruction booklet

RiverGrille

RiverGrille TF2002501-RG Assembly instruction

Vollrath

Vollrath 69504F Operator's manual

Tricity Bendix

Tricity Bendix CSIE500 Operating and installation instructions

AEG

AEG Competence 5731 V Instruction book

Euromaid

Euromaid ES60 Installation and operation manual

Hotpoint

Hotpoint HUI 62 TP Instructions for installation and use