sauter TPE-N User manual
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.sauter.eu
Instruction Manual Peel Test
Attachment
SAUTER TPE-N
Version 1.0
12/2020
GB
TPE-N-BA-e-2010
PROFESSIONAL MEASURING
2 TPE-N-BA-e-2010
GB
SAUTER TPE-N
V. 1.0 12/2020
Instruction Manual Peel Test Attachment
Congratulations on the purchase of the SAUTER TPE-N test stand. We hope you enjoy
your qualitymeasurement system with its wide range offunctions. If operated correctly,
this high-quality product will give you many years of use.
For questions, wishes or suggestions we are always at your disposal.
Table of contents:
1Attaching the TPE-N to a TVO-S 1000/2000 test stand............................... 3
2Technical data................................................................................................ 5
3How it works................................................................................................... 6
4Maintenance................................................................................................... 6
5Scope of delivery........................................................................................... 6
TPE-N-BA-e-2010 TPE-N-BA-e-20103
1 Attaching the TPE-N to a TVO-S 1000/2000 test stand
In order to be able to attach the TPE-N to a TVO-S 1000/2000 test stand, you must
carry out the following steps as preparation:
1.1 Fit the TPE-N running rails according to the drilling pattern of the TVO-S
1000/2000 base plate (marked red). These drill holes must be adjusted on both
tracks of the TPE-N
1.2 Now fix the TPE-N with the two screws supplied (marked yellow)
4 TPE-N-BA-e-2010
1.3 The next step is to mount the force gauge on the TVO-S 1000/2000. Use the
adapter plates supplied with the TVO-S 1000/2000 and the screws provided.
During assembly, clamp the TPE-N thread between the adapter plates (see red
marking in the picture). The position should be as low as possible to have as
much test travel as possible.
1.4 Now you can mount the clamp to the force gauge (here AE 500, red marking)
TPE-N-BA-e-2010 TPE-N-BA-e-20105
1.5 Now glue your test specimen on the TPE-N and clamp one end of the test
specimen in the clamp of the force gauge. IMPORTANT: Glue the test
specimen in the centre of the TPE-N.
1.6 As a last step, wire the test stand and the force gauge according to the operating
instructions provided in order to start the test of the test specimen (possible with
or without software, not included in the scope of delivery).
2 Technical data
Capacity
500N
Maximum tractive force
500N
Maximum length of the test specimen
Up to 200mm
Working temperature
20±10°C
Storage and delivery temperature
-27°C up to 70°C
Relative air humidity
15% up to 80%
6 TPE-N-BA-e-2010
3 How it works
Please check everything before commissioning!
1. The carriage of the device should be checked for easy movement by moving it
back and forth without a suspended load.
4 Maintenance
1. The surroundings of the TPE-N must be kept clean;
2. The rail responsible for the movement should be kept free of liquids or objects.
3. The TPE-N should always be stored dust-free and free from moisture when not
in use.
5 Scope of delivery
•TPE-N
•Adapter plates with screws
•Operating instructions
Table of contents
Other sauter Measuring Instrument manuals
sauter
sauter CP P9 User manual
sauter
sauter CD P2 Instruction Manual
sauter
sauter CT Q1 User manual
sauter
sauter SN User manual
sauter
sauter FA User manual
sauter
sauter TO-EE User manual
sauter
sauter CE WT1-Y1 User manual
sauter
sauter FC User manual
sauter
sauter LB User manual
sauter
sauter SAUTER TG User manual
sauter
sauter HBA 100-0 User manual
sauter
sauter SAUTER TE SERIES User manual
sauter
sauter FH Series User manual
sauter
sauter FK 10 User manual
sauter
sauter FA User manual
sauter
sauter FC 1K-BT User manual
sauter
sauter MFS-3202 User manual
sauter
sauter LA User manual
sauter
sauter FH-M User manual
sauter
sauter SW 1000 User manual
