Prorack K652 User manual
K652
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 6 x 2 x 1 x 1
x 2 x 2 x 4 x 2
Revision No: 3C 1
Fitting Kit K652
MAX kgs (lbs)
W/P WHD
Toyota
Aurion , 4dr Sedan 12-+ NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Aurion , 4dr Sedan 12-+ AU 60 kgs (132 lbs) 60 kgs (132 lbs)
Camry , 4dr Sedan 12-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Camry , 4dr Sedan 12-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Camry , 4dr Sedan 12-+ US 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit EN
K652
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K652
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K652
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 627A
B = 830A
5
Fitting Kit EN
K652
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K652
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-243
B = 11-04-254
C = 11-04-255
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K652
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K652
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K652
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K436 User manual
Prorack
Prorack K038 User manual
Prorack
Prorack K1214 User manual
Prorack
Prorack K482 Operation and installation manual
Prorack
Prorack K408 User manual
Prorack
Prorack K189 User manual
Prorack
Prorack K423 User manual
Prorack
Prorack K420 User manual
Prorack
Prorack K1062 User manual
Prorack
Prorack K813 User manual
Prorack
Prorack K425 Operation and installation manual
Prorack
Prorack EXP360 User manual
Prorack
Prorack K389 User manual
Prorack
Prorack K049 User manual
Prorack
Prorack K890 User manual
Prorack
Prorack K1013 User manual
Prorack
Prorack K483 User manual
Prorack
Prorack K426 User manual
Prorack
Prorack K447 User manual
Prorack
Prorack K694 User manual
