Prorack K686 User manual
K686
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 2 x 2
x 2 x 2 x 1 x 1
x 1 x 1 x 1 x 1
Revision No: 1A 1
Fitting Kit K686
MAX kgs (lbs)
W/P WHD
Hyundai
i40 , 4dr Sedan Feb 13-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
i40 , 4dr Sedan Jan 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
i40 , 4dr Sedan Jun 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K686
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K686
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K686
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 932B
B = 933B
C = 934B
5
Fitting Kit EN
K686
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K686
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-244
B = 11-04-256
C = 11-04-257
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K686
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
8
Fitting Kit EN
K686
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K686
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K410 User manual
Prorack
Prorack PR3077 User manual
Prorack
Prorack K1226 User manual
Prorack
Prorack K1215 User manual
Prorack
Prorack K676 Operation and installation manual
Prorack
Prorack K094 User manual
Prorack
Prorack K178 User manual
Prorack
Prorack K607 User manual
Prorack
Prorack K945 User manual
Prorack
Prorack K488 User manual
Prorack
Prorack K907 User manual
Prorack
Prorack K349 User manual
Prorack
Prorack K446 User manual
Prorack
Prorack Whispbar S43 User manual
Prorack
Prorack K869 User manual
Prorack
Prorack K527 User manual
Prorack
Prorack K596 User manual
Prorack
Prorack K046 User manual
Prorack
Prorack K589 User manual
Prorack
Prorack K513 User manual
