Prorack K483 User manual
K483
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 2 x 2
x 4
Revision No: 3C 1
Fitting Kit K483
MAX kgs (lbs)
W/P WHD
Nissan
Altima , 4dr Sedan 07-13 US 60 kgs (132 lbs) 60 kgs (132 lbs)
2
Fitting Kit EN
K483
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K483
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K483
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 740A
B = 741A
5
Fitting Kit EN
K483
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K483
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-248
B = 11-04-249
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K483
Fitment
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps over body trim.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8
Fitting Kit EN
K483
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K483
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K1188 User manual
Prorack
Prorack K1006 Operation and installation manual
Prorack
Prorack K052 User manual
Prorack
Prorack K488 User manual
Prorack
Prorack K432 User manual
Prorack
Prorack K639 User manual
Prorack
Prorack K623 User manual
Prorack
Prorack K162 User manual
Prorack
Prorack PR3208 User manual
Prorack
Prorack K091 User manual
Prorack
Prorack K175 User manual
Prorack
Prorack K1104 User manual
Prorack
Prorack EXP360 User manual
Prorack
Prorack K687 User manual
Prorack
Prorack K501 User manual
Prorack
Prorack K545 User manual
Prorack
Prorack K358 User manual
Prorack
Prorack K377 User manual
Prorack
Prorack K038 User manual
Prorack
Prorack K448 Operation and installation manual
