Progress Lighting AirPro P250108 User manual

Ceiling Fan Installation Manual

93166072 P250108 / P250113

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No. 109226

P250108 / P250113

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

UPC

785247257003

785247257010

785247257027

10.

12.

13.

14.

Table of Contents

Safety Rules ..................................................................................................................................................................

Unpacking Your Fan .....................................................................................................................................................

Installing Your Fan .......................................................................................................................................................

Installing the Light Kit and Glass Shade .....................................................................................................................

Operating Your Transmitter ........................................................................................................................................

Care of Your Fan .........................................................................................................................................................

Troubleshooting ..........................................................................................................................................................

Specifications ..............................................................................................................................................................

1. To reduce the risk of electric shock, insure electricity has been turned off at

the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use this

fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35

lbs.) Or Less" and use mounting screws provided with the outlet box.

Most outlet boxes commonly used for the support of light fixtures are not

acceptable for fan support and may need to be replaced. Due to the

complexity of the installation of this fan, a qualified licensed electrician

is strongly recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and capable

of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use only

UL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7. To operate the reverse function on this fan, press the reversing button

while the fan is running.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be cautious

when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

11. After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into the outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use Switches.

Refer to the Instructions packaged with the light kits.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

1. Safety Rules

Unpacking Your Fan 2.

15. Loose parts bag containing:

a. Blade attachment hardware

1/4" x 15mm screws with lock washers (19)

b. Mounting hardware

Wire nuts (3)

Unpack your fan and check the contents. You should have the following items:

1. Fan blades (6)

2. Blade support plates (6)

3. Canopy assembly

4. Ball/downrod assembly

5. Collar cover

6. Fan motor assembly

7. Decorative housing

8. 20W LED light kit

9. Glass shade assembly

10. Metal light cover (for no light use)

11. Receiver with 9 wire nuts

12. Transmitter incl. holder + 2 mounting screws

13. 12V MN21/A23 battery

14. Balancing kit

812

14 15

III IV

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet boxes.

Outlet box

Outlet box Outlet box

NOTE: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at your

Progress Lighting Retailer).

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

25 angle

Recessed

outlet box

Provide strong

support

Ceiling

hanger

bracket

3. Installing Your Fan

Figure 1 Figure 3

Figure 4

Figure 2

Step 1.Begin by using the original product

packaging to create a base to hold the fan. Place

the fan motor with the bottom facing up.

Step 2.Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws. (Do

not remove)

Step 3.Place the key holes on the decorative

housing over the 2 screws previously loosened

from the mounting ring, turn decorative housing

until it locks in place at the narrow section of the

key holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 5)

Attaching the Decorative

Housing Attaching the Fan Blades

WARNING: To reduce the risk of personal

injury, do not bend the blades while installing,

balancing the blades, or cleaning the fan.

Step 1. Fasten blade to motor with provided

blade support plates and screws. Make sure

screws are TIGHT! Loose motor screws can

contribute to unnecessary hum or wobble during

operation. (Fig. 6)

Step 2. Repeat these steps for the remaining

blades.

Figura 5

Screw

Screws

Mounting ring

Decorative

housing

Fan motor

assembly

Screws

Blade support

plates

Blades

Figure 6

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Figure 8

Figure 7

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

CUL Listed

electrical

box

120V Wires

Washers

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise.(Fig. 7)

Step 2. Remove the mounting bracket from

the canopy by removing 1 of 2 screws from

the bottom of the mounting bracket and

loosening the other one a half turn from the

screw head. Next, turn the canopy counter

clockwise to remove the mounting bracket

from the canopy. (Fig. 7)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 8.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly. (Fig. 9)

Step 6. Route the wires exiting from the top

of the fan motor through the collar cover,

canopy cover, canopy and then through the

ball / downrod. (Fig. 9)

Step 7. Align the holes at the bottom of the downrod

with the holes in the collar on top of the motor

housing (Fig. 9). Carefully insert the hanger pin

through the holes in the collar and downrod. Be

careful not to jam the pin against the wiring inside

the downrod. Insert the locking pin through the hole

near the end of the hanger pin until it snaps into its

locked position, as noted in the circle inset of Fig. 7.

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 9)

Step 9. Place the downrod ball into the hanger

bracket socket. (Fig. 10)

Ceiling hanger

bracket

Ceiling

canopy

Canopy

cover Figure 9

Supply wires

Set screws

Collar cover

Canopy cover

Canopy

Canopy cover

Pin in locked

position

Collar cover

Ball/downrod

assembly

Canopy

Lock pin

Hanger pin

Set screws

Figure 10

Groove Tab

Figure 11

Hanger

bracket

Receiver

Make the Electrical

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

WARNING: Check to see that all connections are

tight, including ground, and that no bare wire is

visible at the wire nuts, except for the ground wire.

CAUTION: To reduce the risk of electric shock,

this fan must be installed with an isolating wall

control/switch.

NOTE: The fan must be installed at a maximum

distance of 20 ft. from the remote control for

proper signal transmission between the remote

control and the fan's receiving unit.

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts with

your fan. Secure the plastic wire nuts with

electrical tape. Make sure there are no loose

strands or connections.

Step 1. Insert the receiver into the mounting

bracket with the flat side of the receiver facing

the ceiling. (Fig. 11)

Step 2. Make wire connections from the fan to the

receiver. (Fig. 12)

From Fan To Receiver

White Wire ------------ White Wire "For Light"

Blue Wire -------------- Blue Wire "For Light"

Yellow Wire ----------- Yellow Wire

Red Wire --------------- Red Wire

Grey Wire -------------- Grey Wire

Step 3. Make wire connections from the receiver

to the outlet box. (Fig. 12)

From Receiver To Outlet Box

Black Wire "AC in L" ----- Black Wire (Hot)

White Wire "AC in N"----- White Wire (Neutral)

From Fan & To Outlet Box

Receiver

Green Wires* --------

Green or Bare Wire

(Ground)

There are three green grounding leads: from the

mounting bracket, hanger ball/downrod assembly,

receiver.

Step 4. Turn the wire nut connections upward,

spreading them apart so the green (ground) and

white wires will be on one side of the outlet box

and the black and blue wires will be on the other

side. Carefully tuck the connections up into the

outlet box.

Figure 12

White ("AC IN N")

White (Neutral)

Black ("AC IN L")

Black (Hot)

Receiver

Outlet Box

White

Blue

Red

Yellow

Grey

Green

Ground conductor

Green

Canopy

Figure 13

Outlet box

Hanger

bracket

Canopy

Canopy cover

Screws

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket

and place the key hole on the canopy over the

screw on the mounting bracket, turn canopy until it

locks in place at the narrow section of the key

holes. (Fig. 13)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. NOTE: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING

MAKE SURE THE TAB ON THE HANGING

BRACKET PROPERLY SITS IN THE GROOVE

IN THE HANGER BALL BEFORE ATTACHING

THE CANOPY TO THE BRACKET BY

TURNING THE HOUSING UNTIL IT DROPS

INTO PLACE.

This manual suits for next models

Table of contents

Languages:

Other Progress Lighting Fan manuals

Progress Lighting

Progress Lighting AirPro P2548 User manual

Progress Lighting

Progress Lighting AirPro P2556 User manual

Progress Lighting

Progress Lighting AirPro P250016 User manual

Progress Lighting

Progress Lighting AirPro P2596 User manual

Progress Lighting

Progress Lighting AirPro Huff P250030-031 User manual

Progress Lighting

Progress Lighting AirPro P2552 User manual

Progress Lighting

Progress Lighting AirPro P2574-8030K User manual

Progress Lighting

Progress Lighting AirPro P250100 User manual

Progress Lighting

Progress Lighting AirPro P2553 User manual

Progress Lighting

Progress Lighting AirPro P2542-3030K User manual

Progress Lighting

Progress Lighting AirPro P2599 User manual

Progress Lighting

Progress Lighting AirPro P2540-14330K User manual

Progress Lighting

Progress Lighting AirPro P250062 User manual

Progress Lighting

Progress Lighting 52-RDT User manual

Progress Lighting

Progress Lighting AirPro P250110 User manual

Progress Lighting

Progress Lighting AirPro GULLIVER User manual

Progress Lighting

Progress Lighting P2550 User manual

Progress Lighting

Progress Lighting AirPro P250093 User manual

Progress Lighting

Progress Lighting AirPro P2564-3030K User manual

Progress Lighting

Progress Lighting AirPro P250059 User manual

Progress Lighting

Progress Lighting AirPro P250076 User manual

Progress Lighting

Progress Lighting AirPro P2538 User manual

Progress Lighting

Progress Lighting AirPro P2539 User manual

Progress Lighting

Progress Lighting AirPro Royer P250010 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual