Progress Lighting AirPro P250070 User manual

P250070

93140254_A

Date Purch as ed

Sto re Pu rchased

Model No.

Serial No.

Vendor No.

UPC

126900

P250070

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR®qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

UPC

785247248797

785247248810

785247248803

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan .........................................................................................................................................................................

Operating Your Transmitter ....................................................................................................

........................................................

Care of Your Fan ..............................................................................................................

.............................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

10.

11.

1. Safety Rules

1.To reduce the risk of electric shock, ensure electricity has been turned off

at the circuit breaker or fuse box before beginning.

2.All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING:To reduce the risk of electrical shock and fire, do not use

this fanwith any solid-state fanspeed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)

Or Less" and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures are not acceptable for

fan support and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only UL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7.To operate the reverse function on this fan, press the reversing button while

the fan is running.

8. Avoid placing objects in the path of the blades.

9.To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10.Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

13. Loose parts bag containing:

a. Blade bracket attachment hardware

(11 screws)

b. Blade attachment hardware

(21 screws)

c. Mounting hardware

Wire nuts (4)

1. Fan blades (5)

2. Hanger bracket

3. Ball/downrod assembly

4. Canopy

5. Decorative cover

6. Coupling cover

7. Set of blades bracket (5)

8. Fan motor assembly

9. Switch cover

10. Transmitter incl. holder + 2 mounting screws

11. 3V battery

12. Receiver with 6 wire nuts

a b

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Useappropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

Figure 4

Figure 3

Figure 1

Figure 2

Outlet box

Outlet box Outlet box

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Progress Lighting Retailer).

3. Installing Your Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

25 angle

Recessed

outlet box

Provide strong support

Ceiling

hanger

bracket

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 5.

Step 3. Remove the 5 motor screws

preassembled at the bottom of motor

assembly,discarding the screws and the

preassembled shipping blocks. (Fig.6)

Step 2. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 4. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly. (Fig. 7)

Step 5. Route wires exiting from the top of

thefanmotorthroughthecoupling cover,

decorative cover, canopy and then through the

downrod. (Fig. 8)

Step 6. Align the holes at the bottom of the

downrod with the holes in the collar on

top of the motor housing (Fig. 8). Carefully

insert the hanger pin through the holes in

the collar and downrod. Becareful not to

jam the pin against the wiring inside the

downrod. Insert the lock pin through the hole near the

end of the hanger pin until it snaps into its locked

position, and tighten set screws as shown in Fig.8. Cut

off excess fixture wires leaving approximately 6 to 9

inches above top of hanger ball/downrod assembly.

Ceiling hanger

bracket

Set screw

Downrod/ball assembly

6 to 9in

Motor assembly

Motor

assembly

Hanger ball

Hanger pin

Downrod

Canopy

Decorative

cover

Coupling cover

Hanger pin

Lock

Lock pin

Motor

screw

UL Listed

electrical box

Washers

Shipping

block

Mounting screws

(supplied with

electrical box)

120V wires

Figure 5

Figure 6

Figure 7

Figure 8

WARNING

FAILURE TO PROPERLY INSTALL

LOCK PIN AS NOTED IN STEP 6

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

WARNING:To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

WARNING: Fan must be installed at a maximum

distance of 20 feet from the transmitting unit for

Step 7. Carefully lift the assembly and rest the

hanger ball of downrod assembly on the hanger

bracket attached to the outlet box. Be sure the

groove in the hanger ball is lined up with the

tab on the hanger bracket. (Fig.9)

proper signal transmission between the transmitting

unit and the fan’s receiving unit. If you feel you do

not have enough electrical wiring knowledge or

experience, have your fan installed by a licensed

electrician.

Step 1. Connect green wires from EMI filter and

related parts according to the wiring diagram as

shown in Figure 11, make sure EMI filter is properly

seated in outlet box.

Step 2. Place the EMI filter into the ceiling box

before installing the receiver into the bracket. Insert

the receiver into the mounting bracket with the flat

side of the receiver facing the ceiling. (Fig. 10)

Step 3. Motor to receiver electrical connections:

Connect the grey wire from the fan to the grey wire

from the receiver. Connect the red wire from the fan

to the red wire from the receiver. Connect the yellow

wire from the fan to the yellow wire from the

receiver. Connect the blue wire from the fan to the

blue wire from the receiver. Connect the white wire

from the fan to the white wire from the receiver.

(Fig.11)

Step 4. Receiver to house supply wires electrical

connections: Connect the black (hot) wire from the

ceiling to the black wire marked "AC IN L" from the

receiver. Connect the white (neutral) wire from the

ceiling to the white wire marked "AC IN N" from

the receiver. (Fig.11)

Secure all wire connections with the plastic wire

nuts provided.

Hanger

bracket

Hanger

ball

Tab

Groove

Figure 9

OK NO

EMI filter Hanger bracket

Figure 10

Make the Electric

Connections

Figure 11

Blue

White

Blue

White

Ground wire

AC IN L(Black)

AC IN N(White)

Ground wire

Yellow

Red

Gray

Yellow

Red

Ground wire

Gray

Ground wire

Canopy

Decorative

cover

Blade

Switch housing

Switch cover

Blade assembly

Blade bracket

Blade screw

Motor

Blade

bracket

screw

Attach the blades to the blade brackets using four

(4) blade screws as shown in Figure 13. Repeat

this step for the 4 remaining blades and blade

brackets. Tighten the screws securely.

Attached the switch cover to the switch housing

using the three screws from the switch housing.

(Fig.15)

Fasten the blade assembly to the motor using the

blade bracket screws provided as shown in Figure

14. Repeat the same steps until all blades are

installed.

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket and

place the key hole on the canopy over the screw on

the mounting bracket, turn canopy until it locks in

place at the narrow section of the key holes. (Fig. 12)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. Note: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING

Make sure the notch on the hanging bracket properly

sits in the groove in the hanger ball before attaching

the canopy to the bracket by turning the housing until

it drops into place.

Figure 12

Figure 13

Figure 15

Figure 14

Blade Balancing

All blades are grouped by weight. Because

natural woods vary in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct most

fan wobbling problems. Check after each step.

1. Check that all blade and blade arm screws are

secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 16. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance deviation should be equal within

1/8".

3. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

Touching

ceiling

Figure 16

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING,

BALANCING THE BLADES, OR CLEANING

THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN

BLADES.

This manual suits for next models

Table of contents

Languages:

Other Progress Lighting Fan manuals

Progress Lighting

Progress Lighting AirPro P250024 User manual

Progress Lighting

Progress Lighting AirPro Claret P250007 User manual

Progress Lighting

Progress Lighting AirPro P2552 User manual

Progress Lighting

Progress Lighting AirPro P250107 User manual

Progress Lighting

Progress Lighting AirPro P250108 User manual

Progress Lighting

Progress Lighting AirPro P250065 User manual

Progress Lighting

Progress Lighting EF200D User manual

Progress Lighting

Progress Lighting AirPro P250030 User manual

Progress Lighting

Progress Lighting AirPro P250038 User manual

Progress Lighting

Progress Lighting AirPro P2582 User manual

Progress Lighting

Progress Lighting AirPro P2538 User manual

Progress Lighting

Progress Lighting AirPro P250074 User manual

Progress Lighting

Progress Lighting AirPro P2596 User manual

Progress Lighting

Progress Lighting AirPro P250060 User manual

Progress Lighting

Progress Lighting AirPro P2586 User manual

Progress Lighting

Progress Lighting AirPro P2594 User manual

Progress Lighting

Progress Lighting Springer P260004 User manual

Progress Lighting

Progress Lighting AirPro P2556 User manual

Progress Lighting

Progress Lighting AirPro P250071 User manual

Progress Lighting

Progress Lighting AirPro P250089 User manual

Progress Lighting

Progress Lighting AirPro P2554 User manual

Progress Lighting

Progress Lighting P2667 Programming manual

Progress Lighting

Progress Lighting AirPro P2576 User manual

Progress Lighting

Progress Lighting P2550 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual