Progress Lighting AirPro P250110 User manual

Ceiling Fan Installation Manual

P250110

93166076

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No. 109226

P250110

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

UPC 785247257096

785247257089

785247257072

10.

12.

13.

14.

Table of Contents

Safety Rules ..................................................................................................................................................................

Unpacking Your Fan .....................................................................................................................................................

Installing Your Fan .......................................................................................................................................................

Installing the Light Kit and Glass Shade .....................................................................................................................

Operating Your Transmitter ........................................................................................................................................

Care of Your Fan .........................................................................................................................................................

Troubleshooting ..........................................................................................................................................................

Specifications ..............................................................................................................................................................

1. To reduce the risk of electric shock, insure electricity has been turned off at

the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use this

fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35

lbs.) Or Less" and use mounting screws provided with the outlet box.

Most outlet boxes commonly used for the support of light fixtures are not

acceptable for fan support and may need to be replaced. Due to the

complexity of the installation of this fan, a qualified licensed electrician

is strongly recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and capable

of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use only

UL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7. To operate the reverse function on this fan, press the reversing button

while the fan is running.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be cautious

when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

11. After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into the outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use Switches.

Refer to the Instructions packaged with the light kits.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

1. Safety Rules

Unpacking Your Fan 2.

14. Loose parts bag containing:

a. Blade attachment hardware

3/16" x 1/2" screws with lock washers (10)

b. Mounting hardware

Wire nuts (3)

Unpack your fan and check the contents. You should have the following items:

1. Fan blades (3)

2. Blade support plates (3)

3. Canopy assembly

4. Ball/downrod assembly

5. Collar cover

6. Fan motor assembly

7. Decorative frame

8. 20W LED light kit

9. Glass shade

10. Receiver with 9 wire nuts

11. Transmitter incl. holder + 2 mounting screws

12. 12V MN21/A23 battery

13. Balancing kit

III IV

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet boxes.

Outlet box

Outlet box Outlet box

NOTE: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling.

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at your

Progress Lighting Retailer).

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

25 angle

Recessed

outlet box

Provide strong

support

Ceiling

hanger

bracket

3. Installing Your Fan

Figure 1 Figure 3

Figure 4

Figure 2

Hanging the Fan

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom cover

from the canopy by turning the cover counter

clockwise.(Fig. 5)

Step 2. Remove the mounting bracket from the

canopy by removing the 1 of 2 screws from the

bottom of the mounting bracket and loosening the

other one a half turn from the screw head. Next,

turn the canopy counter clockwise to removing the

mounting bracket from the canopy. (Fig. 5)

Step 3. Pass the 120-volt supply wires through the

center hole in the ceiling hanger bracket as shown

in Fig. 6.

Step 4. Secure the hanger bracket to the ceiling

outlet box with the screws and washers provided

with your outlet box. (Fig. 6)

Figure 6

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

UL Listed

electrical

box

120V Wires

Washers

Figure 5

Ceiling hanger

bracket

Ceiling

canopy

Canopy

cover

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 7)

Step 9. Place the downrod ball into the hanger

bracket socket. (Fig. 8)

Figure 7

Hanger pin Lock pin

Supply wires

Canopy

Canopy cover

Collar cover

Downrod

Set screws

Pin in locked

position

Collar

Figure 8

Groove Tab

Step 5. Remove the hanger pin, lock pin and set

screws from the top of the motor assembly. (Fig. 7)

Step 6. Route the wires exiting from the top of the

fan motor through the collar cover, canopy cover

nd canopy and then through the ball/downrod.

(Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of the

motor housing (Fig. 7). Carefully insert the hanger

pin through the holes in the collar and downrod.

Be careful not to jam the pin against the wiring

inside the downrod. Insert the locking pin through

the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the circle

inset of Fig. 7.

Make the Electrical

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

WARNING: Check to see that all connections are

tight, including ground, and that no bare wire is

visible at the wire nuts, except for the ground wire.

CAUTION: To reduce the risk of electric shock,

this fan must be installed with an isolating wall

control/switch.

NOTE: The fan must be installed at a maximum

distance of 20 ft. from the remote control for proper

signal transmission between the remote control

and the fan's receiving unit.

If you feel you do not have enough electrical wiring

knowledge or experience, have your fan installed

by a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts with your

fan. Secure the plastic wire nuts with electrical tape.

Make sure there are no loose strands or

connections.

Step 1. Insert the receiver into the mounting

bracket with the flat side of the receiver facing the

ceiling. (Fig. 9)

Step 2. Make wire connections from the fan to the

receiver. (Fig. 10)

From Fan To Receiver

White Wire ----------- White Wire "For Light"

Blue Wire ------------ Blue Wire "For Light"

Yellow Wire --------- Yellow Wire

Red Wire ------------- Red Wire

Grey Wire ------------ Grey Wire

Step 3. Make wire connections from the receiver

to the outlet box. (Fig. 10)

From Receiver To Outlet Box

Black Wire "AC in L" -----

Black Wire (Hot)

White Wire "AC in N"-----

White Wire (Neutral)

From Fan & To Outlet Box

Receiver

Green Wires* ------

Green or Bare Wire

(Ground)

There are three green grounding leads: from the

mounting bracket, hanger ball/downrod assembly,

receiver.

Step 4. Turn the wire nut connections upward,

spreading them apart so the green (ground) and

white wires will be on one side of the outlet box

and the black and blue wires will be on the other

side. Carefully tuck the connections up into the

outlet box.

Figure 10

White ("AC IN N")

White (Neutral)

Black ("AC IN L")

Black (Hot)

Receiver

Outlet Box

White

Blue

Red

Yellow

Grey

Green

Ground conductor

Green

Canopy

Figure 9

Hanger

bracket

Receiver

Figure 12

Attaching the Fan Blades

Step 1. Insert the blade through the slot in the

housing. Align the holes in the blade and the fan

motor assembly and secure with the blade support

and blade screw with lock washer. (Fig. 12)

Step 2. Repeat these steps for the remaining blades.

Figure 11

Outlet box

Hanger

bracket

Canopy

Canopy cover

Screws

Blade support plates

Blades

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket

and place the key hole on the canopy over the

screw on the mounting bracket, turn canopy until it

locks in place at the narrow section of the key

holes. (Fig. 11)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. NOTE: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING

MAKE SURE THE TAB ON THE HANGING

BRACKET PROPERLY SITS IN THE GROOVE

IN THE HANGER BALL BEFORE ATTACHING

THE CANOPY TO THE BRACKET BY

TURNING THE HOUSING UNTIL IT DROPS

INTO PLACE.

Table of contents

Languages:

Other Progress Lighting Fan manuals

Progress Lighting

Progress Lighting AirPro P250074 User manual

Progress Lighting

Progress Lighting AirPro Verada P2558 User manual

Progress Lighting

Progress Lighting 111017 User manual

Progress Lighting

Progress Lighting AirPro P250065 User manual

Progress Lighting

Progress Lighting AirPro P250082 User manual

Progress Lighting

Progress Lighting EF200D User manual

Progress Lighting

Progress Lighting Springer P260004 User manual

Progress Lighting

Progress Lighting AirPro P2596 User manual

Progress Lighting

Progress Lighting P2514 User manual

Progress Lighting

Progress Lighting AirPro COPAN User manual

Progress Lighting

Progress Lighting AirPro P250072 User manual

Progress Lighting

Progress Lighting AirPro P2574-8030K User manual

Progress Lighting

Progress Lighting AirPro P2540 User manual

Progress Lighting

Progress Lighting AirPro P2564-3030K User manual

Progress Lighting

Progress Lighting AirPro P2572 User manual

Progress Lighting

Progress Lighting AirPro P250066 User manual

Progress Lighting

Progress Lighting AirPro Willacy P250063 User manual

Progress Lighting

Progress Lighting AirPro P250107 User manual

Progress Lighting

Progress Lighting AirPro P2539 User manual

Progress Lighting

Progress Lighting AirPro P250069 User manual

Progress Lighting

Progress Lighting AirPro P2576 User manual

Progress Lighting

Progress Lighting P2529 User manual

Progress Lighting

Progress Lighting AirPro P2588 User manual

Progress Lighting

Progress Lighting AirPro Trevina II P2555 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual