Progress Lighting AirPro CALERA User manual

CALERA Ceiling Fan Installation Manual

93131651_A

P250033

Limited Lifetime

rranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR®qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

ate

Pu rchas

Sto re Pu rch as ed

M od

Serial No.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

Vend o r

UPC

111041

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan

.......................................................................................................................................................................

Installing Your Fan

..........................................................................................................................................................................

Operating Your Transmitter

............................................................................................................................................................

Care of Your Fan ............................................................................................................................................................................

Troubleshooting

................................................................................................................................................... ............................

10.

Specifications ........................................................................................................................................................................ ..........

11.

ble of Contents

1. To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)

Or Less" and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures are not acceptable for

fan support and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

8. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

10. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

11. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits

WARNING

TO REDUCE THE RISK OF

WARNING

PERSONAL INJURY,

DO NOT BEND THE

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only UL-listed outlet boxes marked FOR FAN

SUPPORT.

6. The fan must be mounted with a minimum of 10 ft (3.05m) clearance

from the bottom of the fan guard to the floor.

7. Avoid placing objects in the path of the blades.

afety

ules

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items: 9. Loose parts bag containing:

1. Canopy assembly

2. Cover

3. Ball/downrod assembly

4. LED bulbs (4)

5.Fixture assembly

6. Receiver

7. Remote Control Transmitter

8. 12V battery

a. Mounting hardware Wire nuts (6)

Unpacking

Your

Fan 2.

Tools

Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting

Options

If there isn't an existing cUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Outlet

box

Angled

ceiling

maximum

18.5

angle

Recessed

outlet

box

Provide strong

support

Ceiling

hanger

bracket

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

Figure 1Figure 3

Note: You may need a longer downrod to

maintain proper clearance when installing on a

steep, sloped ceiling.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET Figure 2

Outlet

box

Figure 4Outlet

box

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

3. Installing

Your

Fan

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

Hanging the

Fan

REMEMBER

to turn off the power. Follow

the steps below to hang your fan properly:

Step 1.Route the wires exiting the top of the

fan motor through the cover (D) and then

through the canopy (C) ,downrod (B) and

hanger ball (J) assembly.(Fig.7)

Figure 5

Step 2. Insert the downrod (B) through the

metal cover (D) and canopy (C). (Fig 6)

Step 3. Insert the end of downrod (B) through

the connector (PP),align the two holes in the

downrod (B) and the connector (PP).(Fig.6)

Step 4. Insert a plug pin (GG) through the two

holes in the downrod (B) and the connector

(PP). (Fig.6)

Step 5. Insert the R-shaped pin (HH) though

the hole near the end of the plug pin (GG) until

it snaps into its locked position. (Fig.6)

Step 6. Install the screw (FF) to the connector

(PP), and make sure it’s tighten, Screws (FF)

should be tight against the downrod (B). (Fig.6)

Figure 6

Step 7. Insert the hanger ball (J) onto the

downrod (B), and then insert a plug pin (L)

through the hole in the downrod (B). (Fig.7)

Step 8. Insert the plug pin to the slot cut off in

the hanger ball (J) until it snaps into its locked

position. (Fig.6)

Step9. Use the Screw(K) to lock the hanger

ball (J) to the downrod (B). (Fig.7)

Figure 7

Step 10. Install the Hanger bracket (A) on the

outlet box by using the washer (BB) and

screws(AA) provided with the Outlet box.

(Fig.8)

Step 11. Put the hanger ball (J) through the

open side of the ceiling mounting bracket (A),

and then insert the hanger ball(J) to the slot cut

off in the ceiling mounting bracket(A). (Fig.8)

Figure 8

Make the

Electric

Connections

WARNING: To avoid possible electrical

shock, be sure electricity is turned off at the

main fuse box before wiring.

CODE SWITCH: Codes are set by pushing dip

switches up or down. It is imperative that the

code used for both transmitter and receiver is

exactly the same, otherwise remote controller

will not work. Please note the code switch will

enable you to operate a second remote

controller independently. For example, if you

have two ceiling fans with 2 remote control

units, set 2 different codes for each set of

transmitter/receivers. This means you can

operate each ceiling fan independently.

Your remote control is ready for use after

battery installation. (Fig.9)

Figure 9

Step 1. Fan motor to Receiver Electrical and

Current Limiter Connections: Connect the

Black wire from the fan to Black wire marked

"TO MOTOR L". Connect the White wire from

the fan to the White wire marked "TO

MOTOR N" from the receiver and the White

wire from the Current limiter. Connect the

blue (light) wire to the black wire from the

Current Limiter. Connect the Red wire from the

Current Limiter to the Blue wire from the

Receiver. Secure wire connections with the

plastic wire nuts provided. (Fig. 10)

Step 2. Receiver to House Supply Wires

Electrical Connections: Connect the black (hot)

wire from the ceiling to the black wire

marked "AC in L" from the receiver.

Connect the white (neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire connections

with the plastic wire nuts provided. (Fig. 10)

Step 3. If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with plastic wire

nuts provided. After connecting the wires

spread them apart so that the green and white

wires are on one side of the outlet box and

black and blue wires are on the other side.

Carefully tuck the wire connections up into the

outlet box. (Fig. 10)

Figure 1 0

Step 4. Once the connection has been made,

the receiver inserts into the down rod hanging

bracket. The canopy comes up to cover the

receiver and bracket. (Fig. 11)

Figure 11

An additional safety support is provided to

prevent the fan from falling. Secure the

Support cable to the ceiling joist with screw

and washer. Screw and Support cable holder

lock the fixed Support cable. (Fig. 12)

Figure 12

Installing the canopy:

Step 1. Align the locking slots of the canopy

bracket (A). Push up to engage the slots and to

lock in place. (Fig. 13)

Step 2. Rotate the metal cover (D) clockwise

to lock in the bottom of the canopy. (Fig. 13)

Figure 13

Installing the Fan blades, rattan shade

and bulbs:

Step 1: Install the fan blades (M) onto the fan

motor shaft (U), Put the R-shaped pin (R) into

the motor shaft (U) to lock with a screwdriver

or pliers, Left handed thread on the lock nut

(Q).Install lock nut (Q) onto the motor shaft (U)

after the fan blades (M) is installed. (Fig. 14)

(Fig. 15)

Step 2. Use the screws (H) to lock and secure

the rattan shade (E) and four square arms(G).

(Fig. 14)

Step 3. Screw light bulbs (F) into the fixture

Sockets(S). (Fig. 14)

Figure 14

Figure 15

Installing the

battery

Install

12V

A23 battery (included),

To prevent

damage

transmitter, remove

the

battery

if not used for

long

periods.

(Fig. 16)

Figure 16

Restore power to ceiling fan and test for

proper

operation.

1. "●

●●

●●●

"buttons:

These three buttons are used

to set

the

fan

speed

as follows

(Fig. 17):

●=

Low

speed

●● =

Medium

speed

●●● =

High

speed

2. " " button:

This button turns the fan

off.

The

" "

button turns

the

light ON

OFF and

also

controls the brightness setting. Press and release the

button to turn the light ON or OFF. Press and hold the

button

to set the

desired brightness. The light key has

auto-resume,

it will stay at the same brightness as the

last time

was turned

off.

Figure 17

7. Operating

Your

Transmitter

Table of contents

Languages:

Other Progress Lighting Fan manuals

Progress Lighting

Progress Lighting AirPro P250030 User manual

Progress Lighting

Progress Lighting AirPro P250003 User manual

Progress Lighting

Progress Lighting AirPro P2564-3030K User manual

Progress Lighting

Progress Lighting AirPro P250082 User manual

Progress Lighting

Progress Lighting AirPro P250021 User manual

Progress Lighting

Progress Lighting AirPro P2553 User manual

Progress Lighting

Progress Lighting AirPro P250072 User manual

Progress Lighting

Progress Lighting AirPro P250075 User manual

Progress Lighting

Progress Lighting AirPro P250024 User manual

Progress Lighting

Progress Lighting EF200D User manual

Progress Lighting

Progress Lighting AirPro P250089 User manual

Progress Lighting

Progress Lighting AirPro P2592 User manual

Progress Lighting

Progress Lighting AirPro P250070 User manual

Progress Lighting

Progress Lighting AirPro P250034 User manual

Progress Lighting

Progress Lighting AirPro Midvale P250011 User manual

Progress Lighting

Progress Lighting AirPro P2578 User manual

Progress Lighting

Progress Lighting AirPro P250094 User manual

Progress Lighting

Progress Lighting AirPro P250000 User manual

Progress Lighting

Progress Lighting AirPro P2542-3030K User manual

Progress Lighting

Progress Lighting AirPro P2576 User manual

Progress Lighting

Progress Lighting AirPro Royer P250010 User manual

Progress Lighting

Progress Lighting AirPro P250076 User manual

Progress Lighting

Progress Lighting AirPro P250036 User manual

Progress Lighting

Progress Lighting AirPro Huff P250030-031 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual