Overland Storage ARCvault Series User manual
Part Number 10400024-102 03/2007 ©2007 Overland Storage, Inc. WPage 1 of 4
Introduction
This document describes how to remove and replace a
drive cover assembly on any Overland Storage ARCvault
unit. There are three different types of drive covers:
•2-port cover for a single SCSI drive in the drive bay
•4-port cover for dual SCSI drives in the drive bay
•Fibre Channel (FC) cover for a FC drive
Each drive cover comes complete with a new fan assembly.
Early versions of the ARCvault 12 and 24 featured a SCSI
drive cover (Figure 1) with only a single bus. The newer
drive covers now feature independent buses.
Figure 1. ARCvault 12 and 24 Original Drive Cover
NOTE: If replacing an older single bus drive cover on an
ARCvault 24 with a newer 4-port SCSI drive cover and you want
to retain the daisy-chain configuration for your network, an
optional jumper cable is needed (available separately).
Unpacking
Carefully unpack and verify that you have all the parts:
•Spare drive cover assembly (verify you have the
correct one for your system’s configuration)
•These remove & replace instructions
WARNING: To reduce the risk of electric shock or
damage to equipment, disconnect the power by
unplugging the power cord.
The design of the drive cover makes it easy to change it out
while the ARCvault unit is still mounted in a rack
(Figure 2).
Figure 2. Drive Cover Assembly Locations and Cabling
Electrostatic Discharge Information
A discharge of static electricity can damage micro-circuitry
or static-sensitive devices. To help prevent Electrostatic
Discharge (ESD), observe standard ESD precautions.
ARCvault Series
SCSI/FC Drive Cover Spare
Remove & Replace Instructions
Overview & Notes
ARC-0105
TM
ARC-0013
ARC-0077
ARC-0075
SCSI CableTerminator
Thumbscrews
SCSI Cables
Terminators
ARC-0087
FC Cable
Thumbscrews
Thumbscrews
Original Drive Cover:
Dual SCSI Drive Cover:
FC Drive Cover:
Part Number 10400024-102 03/2007 ©2007 Overland Storage, Inc. WPage 2 of 4
Prepare the Library
1. From the Operator Control Panel (OCP), press Power
> Power Off Library > OK (at the power down
message) to power down the unit.
2. After the unit has shut down, remove the power cord.
3. At the rear, remove the SCSI cable and terminator
from the drive cover.
Replace the Drive Cover
1. Loosen the two thumbscrews on the drive cover.
2. Remove the drive cover as follows:
a. Gently pull the drive cover out and hold it about
2 inches (5cm) below the drive bay (Figure 3).
b. Unplug the fan wiring from the fan connector.
c. Using the guide handles, pull the assembly out
about 1 inch (2.5cm) and unplug the SCSI cable
from the drive.
d. Set the old cover aside.
Figure 3. Removing an Original Drive Cover
3. Install the new drive cover as follows:
a. Holding the drive cover below the drive bay opening,
plug in the fan connector.
b. With the drive assembly still pull slightly out, attach
the SCSI drive cable to the drive (Figure 4).
c. Slide the assembly the rest of the way into the drive
bay.
Figure 4. Installing a Drive Cover for a Single Drive
4. Carefully reseat the drive cover and tighten the two
thumbscrews.
IMPORTANT: Be sure all drive wiring is secure in the space
behind the drive assembly and not caught between the
drive cover and the unit when reseating the cover.
5. Reconnect the SCSI cable and terminator to the
drive cover ports.
6. Plug in the power cord and power on the unit.
7. Check the fan to verify it is working.
Prepare the Library
1. From the Operator Control Panel (OCP), press Power
> Power Off Library > OK (at the power down
message) to power down the unit.
2. After the unit has shut down, remove the power cord.
3. At the rear, remove the SCSI cables and terminators
from the drive cover.
Replace the Drive Cover
1. Loosen the two thumbscrews on the drive cover.
2. Remove the drive cover as follows:
a. Gently pull the drive cover out and hold it about
2 inches (5cm) below the drive bay (Figure 5 on
page 3).
b. Unplug the fan wiring from the fan connector.
c. Using the guide handles, pull the assembly out
about 1 inch (2.5cm) and unplug the SCSI cables
from the drives.
d. Set the old cover aside.
Single Half-Height SCSI Drive
ARC-0044
SCSI
Fan
Connector
Cable
Drive
Cover
Guides
ARC-0120
SCSI
Fan
Connector
Cable
New Drive
Cover
Guides
Dual Half-Height SCSI Drives
Part Number 10400024-102 03/2007 ©2007 Overland Storage, Inc. WPage 3 of 4
Figure 5. Removing an Original Drive Cover
3. Install the new drive cover as follows:
a. Holding the drive cover below the drive bay opening,
plug in the fan connector.
b. With the drive assembly still pull slightly out, attach
the SCSI drive cables to the drives (Figure 6).
c. Slide the assembly the rest of the way into the drive
bay.
4. Carefully reseat the drive cover and tighten the two
thumbscrews.
IMPORTANT: Be sure all drive wiring is secure in the space
behind the drive assembly and not caught between the
drive cover and the unit when reseating the cover.
Figure 6. Installing New Single SCSI Drive Cover
5. Reconnect the SCSI cables and terminators to the
drive cover ports.
NOTE: If using a daisy-chain layout, connect a SCSI jumper
cable (not supplied) between the 2nd and 3rd ports.
6. Plug in the power cord and power on the unit.
7. Check the fan to verify it is working.
Prepare the Library
1. From the Operator Control Panel (OCP), press Power
> Power Off Library > OK (at the power down
message) to power down the unit.
2. After the unit has shut down, remove the power cord.
3. At the rear, remove the FC cable from the drive port.
Replace the Drive Cover
1. Loosen the two thumbscrews on the drive cover.
2. Remove the drive cover as follows:
a. Gently pull the drive cover out and hold it about
2 inches (5cm) below the drive bay (Figure 7).
b. Unplug the fan wiring from the fan connector.
c. Set the old cover aside.
3. Holding the new drive cover below the drive bay
opening, plug in the fan connector.
Figure 7. Installing a New FC Drive Cover
ARC-0043
SCSI
Fan
Connector
Cable
Drive
Cover
Guides
ARC-0107
SCSI Fan
Connector
Cables
New Drive
Cover
Guides
Single Full-Height FC Drive
ARC-0069
Fan
Connector
Drive
Cover
Guides
Part Number 10400024-102 03/2007 ©2007 Overland Storage, Inc. WPage 4 of 4
4. Carefully reseat the drive cover and tighten the two
thumbscrews.
IMPORTANT: Be sure all drive wiring is secure in the space
behind the drive assembly and not caught between the
drive cover and the unit or blocking the port access hole
when reseating the cover.
5. Reconnect the FC cable to the drive port.
6. Plug in the power cord and power on the unit.
7. Check the fan to verify it is working.
All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained
therein are held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that
no right is conveyed to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any
kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the
product(s) or program(s) described in this document at any time. These changes will be incorporated in new editions of this publication.
Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.
Additional Help
You can get additional technical support on the Internet at http://support.overlandstorage.com,
or call 1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or
+1 (858) 571-5555 Option 5 (International).
Other manuals for ARCvault Series
8
Table of contents
Other Overland Storage Storage manuals
Overland Storage
Overland Storage NEO 8000 User manual
Overland Storage
Overland Storage SnapServer User manual
Overland Storage
Overland Storage ARCvault 12 User manual
Overland Storage
Overland Storage NEO 2000e User manual
Overland Storage
Overland Storage PowerLoader User manual
Overland Storage
Overland Storage NEO XL Series User manual
Overland Storage
Overland Storage REO 4600 User manual
Overland Storage
Overland Storage SnapSAN S1000 User manual
Overland Storage
Overland Storage NEO Series User manual
Overland Storage
Overland Storage NEO 8000 User manual
Overland Storage
Overland Storage NEO S-Series User manual
Overland Storage
Overland Storage NEO 200S User manual
Overland Storage
Overland Storage Snap Server 210 User manual
Overland Storage
Overland Storage REO Series User manual
Overland Storage
Overland Storage SnapServer Service manual
Overland Storage
Overland Storage ARCvault 48 User manual
Overland Storage
Overland Storage NEO 8000 User manual
Overland Storage
Overland Storage ULTAMUS Manual
Overland Storage
Overland Storage LoaderXpress Guide
Overland Storage
Overland Storage NEO 8000E User manual
