Optika B-290 User manual
OPTIKA MICROSCOPES - ITALY
Ver. 1.0.0
B-290
OPERATION MANUAL
GUIDA UTENTE
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
BEDIENUNGSANLEITUNG
Page 2
INDEX
1.0 DESCRIPTION page 4
2.0 INTRODUCTION page 6
3.0 UNPACKING AND ASSEMBLY page 6
4.0 USING THE MICROSCOPE page 7
5.0 MAINTENANCE page 8
6.0 TECHNICAL SPECIFICATIONS page 9
7.0 RECOVERY AND RECYCLING page 9
Page 3
This microscope is a scientic precision instrument designed to last for many years with a minimum of main-
tenance. It is built to high optical and mechanical standards and to withstand daily use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this manual.
Safety guidelines
This manual contains important information and warnings regarding safety about installation, use and
maintenance of the microscope. Please read this manual carefully before using the equipment. To
ensure safe use, the user must read and follow all instructions in this manual. OPTIKA products are
designed for safe use in normal operating conditions. The equipment and accessories described in
the manual are manufactured and tested according to industry standards for safety instrumentation
laboratory. Misuse can cause personal injury or damage to the instrument. Keep this manual at hand
close to the instrument, for an easy consultation.
Electrical safety
Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corre-
sponds to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The
user must observe the safety regulations in force in his region. The instrument is equipped with CE
safety marking, in any case the user has full responsibility concerning the safe use of that instrument.
Warning/Caution symbols used in this manual
The user should be aware of safety aspects when using the instrument. Warning or hazard symbols
are shown below. These symbols are used in this manual.
The instructions on this symbol to avoid possible severe personal injuries.
Warning of use; the incorrect operation on the instrument can cause damages
to the person or instrument.
Possibility of electric shock.
Attention: high temperature surfaces. Avoid direct contact.
Technical notes or usage tips.
SAFETY GUIDELINES
Page 4
1.0 DESCRIPTION
EYEPIECE
DIOPTRIC ADJUSTMENT
RING
BINOCULAR
OBSERVATION HEAD
[B-292]
OBJECTIVE
SLIDE CLAMP
COARSE FOCUSING
KNOB
FINE FOCUSING
KNOB
BRIGHTNESS ADJUSTMENT
KNOB (ON LEFT SIDE)
LED
ILLUMINATOR
TENSION ADJUSTMENT
KNOB
IRIS DIAPHRAGM
TRANSLATION
KNOBS
CONDENSER
STAGE
NOSEPIECE
Page 5
1.0 DESCRIPTION
TENSION
ADJUSTMENT KNOB
ON/OFF SWITCH POWER SUPPLY
INPUT JACK
REAR:
TRINOCULAR
OBSERVATION
HEAD [B-293]
PHOTO PORT
Page 6
2.0 INTRODUCTION
This microscope is a scientic precision instrument designed to last for many years with a minimum of main-
tenance. It is built to high optical and mechanical standards and to withstand daily use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this manual.
3.1 The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of
the container and lift the top half of the container. Take some care to avoid that the optical items (ob-
jectives and eyepieces) fall out and get damaged. Using both hands (one around the arm and one
around the base), lift the microscope from the container and put it on a stable desk.
3.2 Place the observation head onto the top of the arm and tighten the lock-screw. Insert the eyepieces
into the eye tubes.
3.3 Connect the provided 6Vdc power supply to the power supply input jack on the rear of the microscope.
3.0 UNPACKING AND ASSEMBLY
The power cord should be used only on network sockets equipped with adequate grounding.
Contact a technician to check the state of your electrical system. If there is no need to install additional
accessories, the instrument is now ready for use. Once positioned and installed with the necessary
components, the microscope is ready to be used. Your microscope is a laboratory instrument de-
signed to last. Handle it always carefully and avoid abrupt vibrations or shocks. Always disconnect the
power cable from the microscope when not in use for long time, while you clean it or when you perform
any maintenance.
AVOID DISASSEMBLING THE INSTRUMENT
Do not disassemble the instrument. This entails the cancellation of the warranty and may cause
malfunction.
Page 7
4.0 USING THE MICROSCOPE
4.1 Adjust the observation head
Loosen the lock-screw, turn the observation head to a comfortable position for observation, and then
lock the lock-screw.
4.2 Place the specimen on the stage
Lock the specimen slide on the mechanical stage using the slide clamp. Ensure that the specimen is
centred over the stage opening by adjusting the coaxial knobs of the stage.
4.3 Lamp settings
The microscope is tted with power white LED illuminator. Before turning on the light, read the section
5.3 about electrical safety precautions. Insert the plug of the 6Vdc power supply into the jack on the
rear and turn on the ON/OFF switch. Turn the brightness adjustment knob to a brightness suitable for
observation.
4.4 Adjust interpupillary distance
Hold the right and left parts of the observation head by both hands and adjust the interpupillary dis-
tance by turning the two parts until one circle of light can be seen.
4.5 Focus and diopter adjustment
Rotate the coarse focusing knob to bring the slide into focus using an objective with a low magnica-
tion. Adjust the ne focusing knob to get the image sharp and clear while observing with your right
eye, then turn the dioptric adjustment ring on the left eyepiece until a sharp and clear image can be
observed also with the other eye. Turn the tension-adjust-knob to get a suitable tension for the focus
system. When the image is in focus, turn the nosepiece to choose the objective you need.
4.6 Condenser adjustment
Raise or lower the condenser through the knob to obtain a clear and uniform illumination of the sam
ple. To center the condenser: completely close the iris diaphragm. Using the condenser centering
screws, move the diaphragm in the center of the eld of view. Then gradually expand the diaphragm
until it is tangent to the edges of the eld of view. If necessary, you can perform an additional adjust
ment.
The condenser is centered when the edges of iris diaphragm are tangent to the eld of view.
4.7 Set the numerical aperture
Adjust the aperture of the iris diaphragm to set the numerical aperture of the illuminator, thus control-
ling image contrast and resolution.
4.8Photo and video capture
To use a camera, for photo or video capturing, connect it to the trinocular tube using the proper
adaptor. Please refer to the camera manuals for further details.
Page 8
5.1 Microscopy environment
This microscope is recommended to be used in a clean, dry and shock free environment with a
temperature of 0-40°C and a maximum relative humidity of 85 % (non condensing). Use a dehumidier
if needed.
5.2 To think about when and after using the microscope
• The microscope should always be kept vertically when moving it and be careful so that no moving
parts, such as the eyepieces, fall out.
• Never mishandle or impose unnecessary force on the microscope.
• Never attempt to service the microscope yourself.
• After use, turn off the light immediately, cover the microscope with the included dust-cover, and keep
it in a dry and clean place.
5.3 Electrical safety precautions
• Before plugging in the power supply, make sure that the supplying voltage of your region matches with
the operation voltage of the equipment and that the lamp switch is in off-position.
• Users should observe all safety regulations of the region. The equipment has acquired the CE safety
label. However, users do have full responsibility to use this equipment safely.
5.4 Cleaning the optics
• If the optical parts need to be cleaned try rst to: use compressed air.
• If that is not sufcient: use a soft lint-free piece of cloth with water and a mild detergent.
• And as a nal option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.
Note: ethanol and ether are highly ammable liquids. Do not use them near a heat source, near
sparks or near electric equipment. Use these chemicals in a well ventilated room.
• Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage
the optics.
• Do not disassemble objectives or eyepieces in attempt to clean them.
5.5 If you need to send the microscope to Optika for maintenance, please use the original packaging.
5.0 MAINTENANCE
Page 9
HEAD: B-292: binocular, 360° rotating, 30° inclined
B-293: trinocular, 360° rotating, 30° inclined. Light split 50/50
EYEPIECES: WF 10X/ 20mm
NOSEPIECE: Quadruple, reversed
OBJECTIVES: E-PLAN 4x, 10x, 40x and 100x (oil immersion)
WORKING STAGE: Double layer with mechanical sliding stage, 150x133mm, moving range
75x50mm . Belt-drive in X direction.
CONDENSER: 1.25 N.A. Abbe type, with iris diaphragm
FOCUSING SYSTEM: Coaxial coarse and ne focusing system, with tension adjustment mechanism
ILLUMINATION: X-LED3, 3.6W, with brightness control.
POWER SUPPLY: Input Voltage of the power supply:
100-240Vac / 50-60Hz
6.0 TECHNICAL SPECIFICATIONS
7.0 RECOVERY AND RECYCLING
Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating
to the reduction in the use of hazardous substances in electrical and electronic equipment and waste dispo-
sal.”
The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be
collected separately from other waste.
The separate collection of this equipment at the end of its lifetime is organized and managed by
the producer. The user will have to contact the manufacturer and follow the rules that he adop-
ted for end-of-life equipment collection. The collection of the equipment for recycling, treatment
and environmentally compatible disposal, helps to prevent possible adverse effects on the environ-
ment and health and promotes reuse and/or recycling of materials of the equipment. Improper dispo-
sal of the product involves the application of administrative penalties as provided by the laws in force.
Pagina 10
INDICE
1.0 DESCRIZIONE pag. 12
2.0 INTRODUZIONE pag. 14
3.0 DISIMBALLAGGIO E MONTAGGIO pag. 14
4.0 UTILIZZO DEL MICROSCOPIO pag. 15
5.0 MANUTENZIONE pag. 16
6.0 SPECIFICHE TECNICHE pag. 17
7.0 MISURE ECOLOGICHE pag. 17
This manual suits for next models
1
Table of contents
Languages:
Other Optika Microscope manuals
Optika
Optika IM-3MET User manual
Optika
Optika IM Series User manual
Optika
Optika B-1000Ti-2 User manual
Optika
Optika XDS-3FL User manual
Optika
Optika B-190 User manual
Optika
Optika LAB User manual
Optika
Optika B-60 Series User manual
Optika
Optika STEREO Instruction Manual
Optika
Optika B-500 MET User manual
Optika
Optika B-500DK User manual
Optika
Optika B-600 Installation manual
Optika
Optika B-1000 POL User manual
Optika
Optika B-500 User manual
Optika
Optika B-150POL-M User manual
Optika
Optika ECOVISION M-100FL User manual
Optika
Optika OPTIStar OS-SZ1 User manual
Optika
Optika B-190 User manual
Optika
Optika SZN Series User manual
Optika
Optika B-1000 POL User manual
Optika
Optika LAB-1 User manual
Popular Microscope manuals by other brands
VWR
VWR VisiScope 384 Series instruction manual
Nikon
Nikon ECLIPSE E200 POL instructions
Leica
Leica DI C800 User's manual & installation instructions
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
Olympus
Olympus SZ61 instructions