Optika B-180 User manual

MICROSCOPES

ITALY

OPTIKA

MICROSCOPES - ITALY

www.optikamicroscopes.com - [email protected]

Ver. 4.1.0

PERATI

N MANUA

GUIDA UTENTE

ANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

EDIEN

ANLEIT

Ryf AG

Bettlachstrasse 2

2540 Grenchen

tel 032 654 21 00

fax 032 654 21 09

www.ryfag.ch

Page 2

INDEX

1.0 DESCRIPTION page 3

2.0 INTRODUCTION page 5

3.0 UNPACKING AND ASSEMBLY page 5

4.0 USING THE MICROSCOPE page 6

4.1 Adjust the observation head

4.2 Place the specimen on the stage

4.3 Lamp settings

4.4 Adjust interpupillary distance

4.5 Focus and diopter adjustment

4.6 Condenser adjustment

4.7 Set the numerical aperture

4.8 Additional filters

5.0 MAINTENANCE page 7

5.1 Microscopy environment

5.2 To think about when and after using the microscope

5.3 Electrical safety precautions

5.4 Cleaning the optics

6.0 TECHNICAL SPECIFICATIONS page 8

7.0 RECOVERY AND RECYCLING page 9

Page 3

1.0 DESCRIPTION

EYEPIECE

DIOPTRIC ADJUSTMENT RING

SLIDE CLAMP

NOSEPIECE

CONDENSER ADJUSTMENT

KNOB

OBJECTIVE

STAGE

CONDENSER-CENTRING

SCREWS

CONDENSER

LED LIGHT

ILLUMINATOR

FLIP OUT FILTER

HOLDER

IRIS DIAPHRAGM

BRIGHTNESS ADJU-

STMENT WHEEL

MAIN BODY

BINOCULAR OB-

SERVATION HEAD

B-182: FRONT VIEW

Page 4

LOCK SCREW

FOCUS STOP KNOB

MAIN CABLE

ON-OFF SWITCH

COARSE FOCUSING

KNOB

MONOCULAR

OBSERVATIONHEAD

B-181: REAR VIEW

TRANSLATION

KNOBS

FINE FOCUSING

KNOB

1.0 DESCRIPTION

Page 5

2.0 INTRODUCTION

This microscope is a scientific precision instrument designed to last for many years with a minimum

of maintenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and

that it must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this ma-

nual.

3.1 The microscope is housed in a moulded Styrofoam container. Remove the tape from the ge of

thecontainerandliftthetophalfofthecontainer.Takesomecaretoavoidthatthe opticalitems

(objectives and eyepieces) fall out and get damaged. Using both hands (one around the arm

and one around the base), lift the microscope from the container and put it on a stable desk.

3.2 Place the observation head onto the top of the arm and tighten the lock-screw. Insert the

eyepiece/s into the eye tube/s. Remove the plastic protection film from the microscope stage.

3.3 The objectives are located in individual protective vials. Remove the objectives from the

vials and insert them into the microscope nosepiece in the order from the lowest magnifica-

tion to the highest, in a clockwise direction from the rear.

3.0 UNPACKING AND ASSEMBLY

Page 6

4.1 Adjust the observation head

Loosen the lock-screw, turn the observation head to a comfortable position for observation,

and then lock the lock-screw.

4.2 Place the specimen on the stage

Lock the specimen slide on the mechanical stage using the slide clamp. Ensure that the spe-

cimen is centred over the stage opening by adjusting the coaxial knobs of the stage.

4.3 Lamp settings

The microscope is fitted with white LED illuminator. Before turning on the light, read the sec-

tion 5.3 about electrical safety precautions. Insert the plug of the cable into the power socket

and turn on the switch on the back of the main body. Turn the brightness adjustment wheel to

a brightness suitable for observation.

4.4 Adjust interpupillary distance

Hold the right and left parts of the observation head by both hands and adjust the interpupil-

lary distance by turning the two parts until one circle of light can be seen.

4.5 Focus and diopter adjustment

Turn the dioptric adjustment ring on the right eye tube until its bottom edge is at zero. Loosen

the focus-stop knob if needed, rotate the coarse focusing knob to bring the slide into focus

using an objective with a low magnification, and then lock the focus-stop knob. Adjust the fine

focusing knob to get the image sharp and clear while observing with your right eye, then turn

the left dioptric adjustment ring until a sharp and clear image can be observed also with the

other eye. Turn the nosepiece to choose the objective you need.

4.6 Condenser adjustment

Turn the condenser adjustment knob to move the condenser up or down for a clear and uni-

form sample illumination. The condenser centring screws can be used to centre the conden-

ser.

4.7 Set the numerical aperture

Adjust the aperture of the iris diaphragm to set the numerical aperture of the illuminator, thus

controlling image contrast and resolution.

4.8 Additional filters

The blue, yellow and frosted glass filters can be inserted in the flip-out filter holder underneath

the condenser.

4.0 USING THE MICROSCOPE

Page 7

5.1 Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with

a temperature of 0-40°C and a maximum relative humidity of 85 % (non condensing). Use a

dehumidifier if needed.

5.2 To think about when and after using the microscope

• The microscope should always be kept vertically when moving it and be careful so that no

moving parts, such as the eyepieces, fall out.

• Never mishandle or impose unnecessary force on the microscope.

• Never attempt to service the microscope yourself.

• After use, turn off the light immediately, cover the microscope with the included dust-cover,

and keep it in a dry and clean place.

5.3 Electrical safety precautions

• Before plugging in the power cord with the supply, make sure that the supplying voltage of

your region matches with the operation voltage of the equipment and that the lamp switch is

in off-position.

• Do not turn the power on and off, off and on immediately as this will shorten the life span of

the bulb and may cause damage to the electrical system.

• Users should observe all safety regulations of the region. The equipment has acquired the CE

safety label. However, users do have full responsibility to use this equipment safely.

5.4 Cleaning the optics

• If the optical parts need to be cleaned try first to: use compressed air.

• If that is not sufficient: use a soft lint-free piece of cloth with water and a mild detergent.

• And as a final option: use the piece of cloth moistened with a 3:7 mixture of ethanol and

ether.

Note: ethanol and ether are highly flammable liquids. Do not use them near a heat source,

near sparks or near electric equipment. Use these chemicals in a well ventilated room.

• Remember to never wipe the surface of any optical items with your hands. Fingerprints can

damage the optics.

• Do not disassemble objectives or eyepieces in attempt to clean them.

5.5 If you need to send the microscope to Optika for maintenance, please use the original packa-

ging.

5.0 MAINTENANCE

Page 8

HEAD: MONOCULAR, 360° ROTATING, 45° INCLINED OR BINOCULAR AND

TRINOCULAR, 360° ROTATING, 30° INCLINED

EYEPIECES: WF10X/18MM

NOSEPIECE: QUADRUPLE, REVERSED

OBJECTIVES: ACHROMATIC 4X, 10X, 40X

WORKING STAGE: DOUBLE LAYER WITH MECHANICAL SLIDING STAGE, 125X115MM, MOV.

RANGE 50X30MM

CONDENSER: 1.25 N.A. ABBE TYPE, WITH CENTRING SYSTEM

FOCUSING SY-

STEM:

COAXIAL COARSE AND FINE FOCUSING SYSTEM, WITH FOCUSING

STOP MECHANISM

ILLUMINATION: WHITE LED, NON-RECHARGEABLE, WITH BRIGHTNESS CONTROL

MAINS POWER: 220V / 50 HZ

FUSE: 2A (UNDERNEATH THE BASE)

6.0 TECHNICAL SPECIFICATIONS

Page 9

The appliance reports the symbol:

This symbol means that the appliance can be a precious source of raw materials. Therefore, it must

not be disposed of as waste, but separately collected for the recycling and the recovery of the mate-

rials it contained in it. Such materials, if improperly dispersed into the environment, can be harmful

to the environment and to human health.

The producer of the equipment, Optika Microscopes, recovers, re-uses and recycles the raw mate-

rials contained in the equipment. Such recovery, however, needs your help.

When, at the end of its operating life, you shall decide to dispose of the apparatus, do not try to open

it, nor to use parts of it in ways other than reported in this Manual, but bring it back to the Distributor

you bought it from, or to other Optika Microscopes distributors. The Distributor shall collect the ap-

paratus free of charge.

The recovery of the raw materials shall then take place in accordance with the European Directive

2002 / 96 / EC and all other relevant Directives. Never disassemble, nor dispose of as waste, appa-

ratus reporting the “crossed bin” symbol indicated above.

7.0 RECOVERY AND RECYCLING

Pagina 10

INDICE

1.0 DESCRIZIONE pag. 11

2.0 INTRODUZIONE pag. 13

3.0 RIMOZIONE DELL’IMBALLAGGIO E MONTAGGIO pag. 13

4.0 UTILIZZO DEL MICROSCOPIO pag. 14

4.1 Regolare la testa per l’osservazione

4.2 Mettere il campione sul piatto portaoggetti

4.3 Regolazione della lampadina

4.4 Regolare la distanza interpupillare

4.5 Regolazione della messa a fuoco e della diottria

4.6 Regolazione del condensatore

4.7 Regolare l’apertura numerica

4.8 Filtri supplementari

5.0 MANUTENZIONE pag. 15

5.1 Condizioni dell’ambiente per l’uso del microscopio

5.2 Da considerarsi al momento dell’utilizzo del microscopio

e dopo il suo uso

5.3 Precauzioni ai fini della sicurezza elettrica

5.4 Pulizia degli oculari

6.0 CARATTERISTICHE TECNICHE pag. 16

7.0 RICICLO E RECUPERO pag. 17

Table of contents

Languages:

Other Optika Microscope manuals

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Olympus

Olympus SZ61 instructions