Onicon D-100 User manual

D-100 FLOW DISPLAY

Siemens P1-FLN Network Interface Installation Guide

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699

www.onicon.com • [email protected] 03-18

0660-5 / 18343

Siemens P1-FLN

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 2

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 3

TABLE OF CONTENTS

1.0 INTRODUCTION ..................................................................................................5

1.1 PURPOSE OF THIS GUIDE .......................................................................5

1.2 TYPICAL D-100 NETWORK INTERFACE MODULE ...............................5

1.3 SPECIFICATIONS ......................................................................................5

1.4 NETWORK SIGNAL CONNECTIONS.......................................................6

1.4.1 Standard Network Interface ........................................................6

1.4.2 Optional Network Interface with

Isolated Digital Pulse Input (Di3)................................................7

1.5 RS485 BIASING AND TERMINATION...................................................10

1.6 NETWORK ADDRESSING.......................................................................10

1.6.1 Changing the Device Address ...................................................10

1.7 ENABLING/DISABLING FRONT PANEL RESET...................................12

1.8 D-100-P1 POINT DATABASE..................................................................12

1.8.1 Application Number..................................................................13

1.8.2 D-100-P1 Point Database ...........................................................14

2.0 NETWORK IMPLEMENTATION STRATEGIES ................................................15

2.1 IMPLEMENTATION STRATEGIES .........................................................15

2.2 OTHER FUNCTIONALITY......................................................................16

APPENDIX

A-1 D-100 PROCESSOR BOARD

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 4

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 5

SECTION 1: INTRODUCTION

1.1 PURPOSE OF THIS GUIDE

The purpose of this guide is to provide installation and commissioning procedures and basic

operating and servicing instructions for the ONICON D-100-P1 network interface.

1.2 TYPICAL D-100 NETWORK INTERFACE MODULE

The D-100 is a totalizing display module that provides a local indication of liquid, gas or steam

ow rate and total data. It can also be provided with an optional Siemens P1 RS485 network

interface to communicate data to the building control network.

D-100

SCROLL RESET PROGRAM

ONICON

3864

Steam Building

Domestic Water Supply

Flow rate and total data to

Data Acquisition System or

Building Control System

120VAC or 24VAC

Input Voltage

1.3 SPECIFICATIONS

SIEMENS P1 NETWORK INTERFACE

Transceiver: 2-wire, half duplex

MAC address (device address) range: 1-99, (default: 017)

Baud rate: 4800

Termination: None

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 6

1.4 NETWORK SIGNAL CONNECTIONS

1.4.1 Standard Network Interface

P1 RS485, 2-wire (half duplex) serial output connections are connected to terminals as

shown. Do not exceed 4.4 in-lb (0.5Nm) of torque when tightening.

CAUTION

Only qualied service personnel should make connections between the D-100 and the user’s

external equipment. ONICON assumes no responsibility for damage caused to the external

equipment as a result of an improper installation.

CAUTION

Incoming and outgoing RS485 cable shield wires should be connected together, but must not be

connected to the D-100.

P1 (-)

P1 (+)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 7

1.4.2 Optional Network Interface With Optional Isolated Digital Pulse Input (Di3)

The D-100-P1 Display can be provided with an auxiliary input pulse for totalizing pulse

outputs from external devices such as water or gas meters. Pulses are accumulated in an

internal register, and the totalized value is available on the network. This register can be

zeroed via the network.

If the auxiliary pulse input option was ordered at the same time the display was ordered,

it will arrive fully congured and ready to use. If it was ordered after the display was

delivered and is being installed as a eld upgrade, it may be necessary to congure the

pulse input. The information is provided below and on the following pages:

The input pulse must meet the following criteria:

1. Frequency input range, 50 Hz maximum

2. 10 millisecond minimum pulse duration

Input Pulse Denition:

In order to congure the communications card for an auxiliary input pulse, you must

rst determine which type of pulse your meter produces. The allowable types of input

pulses are described on the following pages. Based on the type of pulse, set the selector

switch (S1) on the communications circuit board (Fig. 1) to the correct setting.

Fig. 1

AUX PULSE INPUT (Di3)

CONNECTOR (T2)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 8

Powered Pulse:

This type of output refers to a pulse which has an associated voltage with it (see Fig. 2).

Set the selector switch, S1 to Pwrd Pulse. The allowable voltage range is 5-24 VDC. The

input impedance is set at the factory to be 11 KOHM via the impedance selector jumper

(J1, see Fig. 1). A lower impedance, 3 KOHM can be selected if required by the instrument

providing the pulse output. Consult the instrument manufacturer or ONICON if you are

uncertain as to the proper jumper selection.

Fig. 2

Open Collector (Sourcing):

This type of output refers to an open Collector Switch congured for a sourcing function

(see Fig. 3). Set the selector switch, S1 to SRC. The switch must be rated for at least 20 mA

at 20 VDC.

Fig. 3

Di3 In (+)

Di3 In (-)

Di3 In (+)

Di3 In (-)

ONICON

BTU METER

ONICON

BTU METER

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 9

Open Collector Sinking or Dry Contact:

This type of output refers to an open collector switch congured in a current sinking

arrangement or a dry contact switch (see Fig. 4 and 5). Set the selector switch, S1 to Sink.

In either case, the switch must be rated for at least 20 mA at 20 VDC.

Fig. 4

Fig. 5

Di3 In (+)

Di3 In (-)

Di3 In (+)

Di3 In (-)

ONICON

BTU METER

ONICON

BTU METER

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

D-100-P1 Flow Display Manual 03/18 - 0660-5 / 18343 Page 10

1.5 RS485 BIASING AND TERMINATION

The ONICON D-100-P1 does not provide biasing voltage or termination to the RS485 network. A

120Wtermination resistor should be used when the display is installed at the end of the line.

1.6 NETWORK ADDRESSING

Before the D-100 can communicate on the P1 network, the appropriate device address must be

programmed into the display. The P1 network address for ONICON D-100 Flow Displays may

be set to any address from 1 to 99. This address is set at the display. Section 1.6.1 details the

procedure for changing this address.

1.6.1 Changing the Device Address

Every ONICON D-100 is individually programmed at the factory with application specic

data provided by the customer during the ordering process, and this may include network

addressing information. If the device address information was provided, the display

will be programmed with that number. If no address is provided, ONICON displays are

programmed with a default address of 017. The address may be changed at the D-100

using the procedure outlined in the table below.

STEP ACTION REACTION COMMENT

0Obtain a device address from the

network administrator.

The device address is

a three digit number

between 1 - 99, excluding

zero.

With the display running, open

the front panel and locate switch

DEV ADD/PROG ENAB. Press

DEV ADD/PROG ENAB and then

release it.

None

The DEV ADD/PROG ENAB

is located on the processor

board. (See appendix page

A-1.)

2 Close the front panel.

Press the PROGRAM button. (If

you do not press the PROGRAM

button, the display will revert to

the RUN mode after 5 minutes.)

The D-100 changes to

PROGRAM mode and the

DEVICE ID page will

appear with the rst digit

of the address ashing.

The PROGRAM button is on

the front panel.

Other manuals for D-100

Table of contents

Other Onicon Measuring Instrument manuals

Onicon

Onicon Vortex Flow Meter F-2200 Series Operating instructions

Onicon

Onicon FB-3500 Operating instructions

Onicon

Onicon FT-4600 Operating instructions

Onicon

Onicon FT-3400 Operating instructions

Onicon

Onicon F-4300 Original operating instructions

Onicon

Onicon F-5100 Inline Operating instructions

Onicon

Onicon Fox Thermal FT2A User manual

Onicon

Onicon FT-3000 Series User manual

Onicon

Onicon F-3100 Series Assembly instructions

Onicon

Onicon D-100 User manual

Onicon

Onicon D-100 Operating instructions

Onicon

Onicon System-10 BTU Meter User manual

Onicon

Onicon SYSTEM-20 Operating instructions

Onicon

Onicon F-4400 User manual

Onicon

Onicon SYSTEM-20 Operating instructions

Onicon

Onicon F-5000 Operating instructions

Onicon

Onicon D-1401 Operating instructions

Onicon

Onicon SYSTEM-30 Operating instructions

Onicon

Onicon F-1100 Series User manual

Onicon

Onicon SeaMetrics EX90 User manual

Onicon

Onicon F-4600 Series Operating instructions

Onicon

Onicon System-10 BTU Meter User manual

Onicon

Onicon System-10 BTU Meter Operating instructions

Onicon

Onicon SYSTEM-40 Operating instructions

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual