OHAUS I-DT33P User manual

i-DT33P / i-DT33XW Indicator

Ethernet Option

Instruction Manual

EN-1

INTRODUCTION

This Ethernet interface kit is for use with the Defender®3000 i-DT33P and i-

DT33XW indicators.

KIT CONTENTS

Cable

Screws(3)

Ethernet

Cable

Ethernet

PC

Board

Watertight

Seal (with

One or Two

Holes)

CAUTION: THE INSTALLATION AND CONNECTIONS SHOULD

ONLY BE PERFORMED BY AUTHORIZED AND QUALIFIED

PERSONNEL, SUCH AS AN ELECTRICIAN.

EN-2

INTERFACE INSTALLATION

Install the Ethernet Interface kit to the indicator as the following.

WARNING: BEFORE INSTALLATION, POWER OFF THE

INDICATOR AND REMOVE ALL EXTERNAL AC POWER

CONNECTIONS.

i-DT33P

1. Remove the battery cover in the direction of the arrow, and take out dry

batteries if used.

2. Slightly push the end of the charging cover (circled) in the direction of the

arrow and take it out.

EN-3

3. Remove the Ethernet sealing plug upwards.

4. Take out the cable supplied. Connect one side to the main board connector

(circled), and pass the other side through the side hole.

EN-4

5. Take out the Ethernet PC board supplied. Connect the cable's another side to

the connector on the Ethernet board (circled). Then insert the Ethernet board

into the two card slots (circled) on both sides.

6. Take out the Ethernet cable supplied, and pass it through the hole where the

sealing plug is removed, and then connect the Ethernet interface to the

connector on the Ethernet board (circled).

Ethernet PC board

EN-5

7. Re-install the dry batteries if used and close the battery cover to finish

installation.

i-DT33XW

1. Remove the six hex head bolts from the rear housing of the indicator.

EN-6

2. Release the strain relief for option connector (circled) including the watertight

seal in it on the bottom of the indicator and remove the plug at the end of it.

3. Take out the cable and the Ethernet PC board supplied. Connect one side of

the cable to the connector on the Ethernet PC board (circled) and the other to

the indicator's main board connector (circled).

Watertight Seal （with One Hole）

Plug

EN-7

4. Pin the upper right corner of the Ethernet PC board on the positioning column

(circled). Make sure the back of the Ethernet PC board is facing up.

5. Screw the two screws (circled) on the Ethernet PC board to the indicator.

Pass the Ethernet cable through the strain relief for option connector and

attach the watertight seal to it, and then connect the Ethernet interface to the

connector on the Ethernet board (circled).

EN-8

Note: If you install RS232 and the Ethernet kit at the same time, please use the

supplied watertight seal with two holes. Make sure to install the RS232 cable first

before the connection of Ethernet kit. Pass the RS232 cable through one hole of

the watertight seal and the Ethernet cable through another.

Watertight Seal （with Two Holes）

Other manuals for i-DT33P

2

This manual suits for next models

1

Table of contents

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual