OHAUS TD52 User manual
TD52 Indicator
USB Host Option
(For Wireless Communication Option)
Instruction Manual
Interfaz de host USB
(Para conexiones inalámbricas)
Manual de instrucciones
Interface hôte USB
(Pour connexion sans fil)
Manuel d’instruction
USB Host-Schnittstelle
(für drahtlose Verbindung)
Bedienungsanleitung
Interfaccia Host USB
(Per collegamento wireless)
Manuale di Istruzioni
USB
幍折ↅ
᧤䞷ℝ㡯兎扭㘴᧥
∎䞷広㢝
EN-1
INTRODUCTION
This Interface Kit is for use with Ohaus TD52 products and Wi-Fi dongle.
KIT CONTENTS
INTERFACE INSTALLATION
For TD52P version
1. Separate the indicator from the base by loosening load cell cable male connector.
Remove the Interface option cover.
Load cell cable male connector
Interface option cover
EN-2
2. Break off the rib of the interface option cover as shown.
3. Connect the 9 pin USB Host Board cable to the main board connector.
4. Install the USB Host board. Secure it with the 2 screws.
Cable
Main board
connector
Rib
EN-3
5. Connect the USB Host cable to the 9 Pin connector on the option board.
6. Plug the USB donglein and put theinterface option cover back on the terminal.
Screw
9 Pin
connector
USB Dongle
EN-4
For TD52XW version:
1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as
shown.
2. Rotate the rear housing down away from the front housing as shown.
Screw
M25 hole plug
Load cell cable male
connector
EN-5
3. Connect 9 pin USB Host Board cable to the main board connector.
4. Install the USB host board. Secure it with 2 screws. (Note: Boss Post is 2 and 4.)
Cable
Main board connector
Boss Post 2, 4
EN-6
5. Connect the USB Host cable to the 9 Pin connector on the option board.
6. Put the rear housing back on the front housing. Fasten 6 screws with sealed washer. Plug
the USB Dongle through M25 hole.
7. Fasten the USB dongle cover.
Screw
9 Pin connector
USB Dongle
USB dongle cover
EN-7
For TD52XW with reversed rear cover:
1. Remove the 6 sealing screws to open the rear housing. Remove the M25 hole plug as
shown.
2. Rotate the rear housing down away from the front housing as shown.
Screw
Load cell cable connector
M25 hole plug
EN-8
3. Connect the USB Host cable to the main board connector.
4. Install the USB host board. Secure it with 2 screws. (Note: Boss Post is 1, 3)
Cable
Main board
connector
Boss post 1, 3
Other manuals for TD52
7
Table of contents
Languages:
Other OHAUS Measuring Instrument manuals
OHAUS
OHAUS Ranger 3000 Series User manual
OHAUS
OHAUS a-AB33M1 User manual
OHAUS
OHAUS MB27 User manual
OHAUS
OHAUS i-DT33P User manual
OHAUS
OHAUS Defender 6000 User manual
OHAUS
OHAUS MB120 User manual
OHAUS
OHAUS Defender 2000 Series User manual
OHAUS
OHAUS ST400 User manual
OHAUS
OHAUS ST20M Series User manual
OHAUS
OHAUS 8000 Series User manual
OHAUS
OHAUS MB90 User manual
OHAUS
OHAUS MC2000 User manual
OHAUS
OHAUS ST300 User manual
OHAUS
OHAUS TD52 User manual
OHAUS
OHAUS MB23 User manual
OHAUS
OHAUS TD52 User manual
OHAUS
OHAUS Defender i-DT61PW User manual
OHAUS
OHAUS CD-1 User manual
OHAUS
OHAUS Ranger 3000 Series User manual
OHAUS
OHAUS MB90 User manual
