NF ZA57630 User manual

NF Corporation

IMPEDANCE ANALYZER

ZA57630

INSTRUCTION MANUAL

(BASICS)

IMPEDANCE ANALYZER

ZA57630

INSTRUCTION MANUAL

(BASICS)

DA00068820-003

Registered Trademarks

National Instruments, LabVIEW, and Measurement Studio are registered trademarks of National

Instruments Corporation in the United States.

WINDOWS® EMBEDDED 8.1 INDUSTRY PRO

Used with permission from Microsoft.

Other company names and product names used in this instruction manual may be trademarks or

registered trademarks of their respective companies.

NI Measurement Studio

i ZA57630

──── Preface ────

Thank you for purchasing the "ZA57630 IMPEDANCE ANALYZER".

For safe and correct use of this product, please read the "Safety Precautions" section that follows

before attempting to use this instrument.

■Marks and symbols

For safe operation by the user and to prevent damage to this instrument, please give attention to the

following marks and symbols that are used in this manual.

！

WARNING

This mark indicates information for preventing the possibility of death or serious

personal injury from electrical shock or other hazards or damage to this instrument

in the use or handling of this instrument.

！

CAUTION

This mark indicates information for preventing the possibility of injury to the user or

damage to this instrument and the use for handling of this instrument.

■The scope of this Manual

This manual describes the ZA57630 that conform to requirements of CE marking.

Products without CE marking affixed, may not meet directives for CE marking (EMC and others).

Please confirm the CE marking is affixed on the rear panel.

Preface

ii ZA57630

The manuals provided for the ZA57630 are listed below.

●Instruction manual (Basics)

This manual describes operation of the ZA57630 from this instrument’s control panel,

specifications, and other basic matters.

If you’re using this equipment for the first time, begin reading from Chapter 1.

●Instruction manual (Advanced)

This manual describes more advanced operation and maintenance.

●Instruction manual (Remote Control)

This manual describes remote control of the ZA57630

Basics

1. Introduction

This chapter provides a general description of this instrument, including its features,

applications, functions, and basic operating principles.

2. Preparation before use

This chapter describes important preparation that must be done before operating this

instrument.

3. Panel operations

This chapter explains the function, operating procedure, default values, and measurement

values for each part of the display screen. Read this chapter for a quick overall understanding

of the panel and its use.

4. Basic operation

This chapter explains the basic operating procedures of the ZA57630. Refer to this chapter as

you use this instrument.

5. Specifications

This chapter describes this instrument specifications (functions and performance).

Advanced

1. Advanced operation

This chapter explains a wider range of operations.

2. File formats

This chapter explains the various file formats for saving data in external storage devices

(USB memory device).

3. Troubleshooting

This chapter describes how to deal with error messages and cases in which you think this

instrument is malfunctioning.

4. Maintenance

This chapter explains maintenance, repacking, transportation, and performance testing

methods.

iii ZA57630

──── Safety Precautions ────

For safe use of this product, give full attention to the following warnings and cautions.

The NF Corporation shall not be held liable for damages that arise from failure to observe these warnings

and cautions.

This product is a Class I device (with protective conductor terminal) that conforms to the IEC insulation

standards.

Be sure to observe the instructions in the instruction manual.

This instruction manual contains information for the safe operation and use of this product.

Read the instructions and information before using the product.

All of the warning items contained in this instruction manual are intended to avoid risks that may lead

to serious accidents. Follow the warnings and instructions carefully.

Be certain that the product is properly grounded.

This product uses a line filter which may cause electric shock if the product is not grounded.

To prevent electrical shock accidents, connect the product to an earth ground so that ground resistance

is 100 Ωor less.

This product is automatically grounded by connecting a 3-pin power plug to a power outlet with a

protective ground contact.

Check the power supply voltage.

This instrument operates on the power source voltage described in "2.3 Grounding and Power

Connections".

Before plugging in the power cord, confirm that the outlet voltage conforms to the rated voltage of

this instrument.

If you think something is wrong, ...

If smoke or an unusual odor or sound comes from this instrument, immediately remove the power

cord from the socket and cease use of this instrument.

If any such abnormality occurs, take measures to prevent the use of this instrument until repairs have

been completed and promptly contact the NF Corporation or its authorized agent.

Do not use this product when gas is present.

Operating this instrument in the presence of flammable gases may cause an explosion.

Do not open the product case.

To prevent exposure to high voltages, never remove the cover of this instrument.

Only technicians certified by the NF Corporation are authorized to inspect or touch anything inside

the product case.

Safety Precautions

iv ZA57630

Do not modify this product.

Never modify this product in any way. Modification might create new risks. The NF Corporation may

refuse to service an instrument that has an unauthorized modification.

Do not expose this product to water.

Use of this product when it is wet may result in electrical shock or fire. If this instrument becomes wet,

immediately unplug the power cord and contact the NF Corporation or its authorized agent.

If lightning occurs nearby, turn off the power switch and unplug the power cord.

A lightning strike may cause electrical shock, fire, or instrument malfunction.

Safety-related symbols

The marks and codes defined below are used in this manual or on this instrument itself to indicate

safety information or instructions.

！

Instruction manual reference symbol

This notifies the user of a potential hazard and indicates that the user must

refer to the instruction manual.

Electric shock danger symbol

This symbol indicates a location that presents a risk of electric shock under

specific conditions.

Warning symbol

This contains information to avoid risks when handling the equipment that

could result in the death or serious injury of the operator.

Caution symbol

This contains information to avoid risks when handling the equipment that

could result in minor or moderate injury of the operator or damage to

property.

Other symbols

Indicates that the "ON" position of the power switch

Indicates the "OFF" position of the power switch

Indicates that the outer conductor of the connector is connected to this instrument

enclosure.

Indicates that the outer conductor of the connector is isolated from this instrument enclosure.

However, safe operation of this instrument requires that the potential difference from the

grounding potential is restricted to 42 Vpk or less.

This product is grounded when in use, so the electrical potential of this instrument enclosure is equal to

the ground potential.

！

CAUTION

！

WARNING

42Vpk

Safety Precautions

v ZA57630

Electromagnetic compatibility

This product is a CISPR 11 Group 1 Class A compliant instrument. It should not be used outside

industrial environments. Use of this product in ordinary office or residential areas may result in

electromagnetic interference with other devices.

Disposal of this product

To protect the environment, follow the guidelines described below for the disposal of this product.

a) This device is equipped with a lithium battery. Use the services of an industrial waste disposal

contractor to dispose of such batteries.

b) The LCD backlight module that is used in this product does not contain mercury.

c) Use the services of an industrial waste disposal contractor for disposal of the entire product.

vi ZA57630

Contents

Page

1. Introduction..............................................................................................................................1-1

1.1 Features...........................................................................................................................1-2

1.2 Applications......................................................................................................................1-3

1.3 Operating Principle...........................................................................................................1-4

2. Preparation before Use............................................................................................................2-1

2.1 Checking before Use........................................................................................................2-2

2.2 Assembly and Installation.................................................................................................2-4

2.3 Grounding and Power Supply Connection .....................................................................2-10

2.4 Simple Operation Check ................................................................................................2-12

2.5 Calibration......................................................................................................................2-13

3. Panel Operations.....................................................................................................................3-1

3.1 Functions and Operations of Panel Parts.........................................................................3-2

3.2 Input and Output Connectors ...........................................................................................3-8

3.3 Overview of the Operation Screens................................................................................3-19

3.4 Operation Tree ...............................................................................................................3-32

3.5 Setting Screen Reference ..............................................................................................3-42

3.6Initial Settings................................................................................................................3-111

4. Basic Operations.....................................................................................................................4-1

4.1 Display and Operation when Power Is Turned On............................................................4-2

4.2 Simple Operation for First Time Use ................................................................................4-5

4.3 Setting Measurement Signals.........................................................................................4-13

4.4 Measurement Controls...................................................................................................4-18

4.5 Setting Sweep Measurement .........................................................................................4-19

4.6 Setting Spot Measurement.............................................................................................4-25

5. Specifications...........................................................................................................................5-1

5.1 Measurement Modes........................................................................................................5-2

5.2 Measurement Value Display Ranges ...............................................................................5-3

5.3 Measurement Connectors (Measurement Mode IMPD−EXT)..........................................5-5

5.4 Measurement Connectors (Measurement Mode IMPD−3T).............................................5-8

5.5 Measurement Connectors (Measurement Mode IMPD−2T)........................................... 5-11

5.6 Measurement Connectors (Measurement Mode G−PH)................................................5-14

5.7 Measured Signal Control Section...................................................................................5-18

5.8 Measurement Accuracy..................................................................................................5-20

5.9 Measurement Processing Section..................................................................................5-31

5.10 Display Section............................................................................................................5-35

Table of contents

Other NF Measuring Instrument manuals

NF ZM2371 User manual

NF FRA51602 User manual

NF ZM2376 User manual

NF FRA51615 User manual

NF FRA51602 User manual

NF ZM2376 User manual

NF FRA5022 User manual

NF FRA51615 User manual

NF FRA5087 User manual

NF FRA5097 User manual

NF FRA5014 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual