National Instruments PXI-8109 User manual

INSTALLATION GUIDE

NI PXI-8109 and NI PXIe-8133

Flex Cable Replacement

This guide describes how to install the flex cable replacement for the

NI PXI-8109 and NI PXIe-8133 embedded controllers. For more detail and

a video demonstration of the cable replacement, please visit ni.com/info

and enter the Info Code 8133FlexReplace.

The flex cable can be replaced by hand. No tools are needed and the

controller does not need to be disassembled. Perform the following steps

for installation and removal instructions.

1. Locate the single-ended board to board flex cable on your

NI PXI-8109 or NI PXIe-8133 embedded controller as shown below in

Figure 1.

Figure 1. View of the Controller Back End with Board to Board Flex Cable

Caution Touch the metal part of the case to discharge any static electricity that might be

on your clothes or body.

1 Board to Board Flex Cable

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle

logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at

ni.com/trademarks for other National Instruments trademarks. Other product and company

names mentioned herein are trademarks or trade names of their respective companies. For patents

covering National Instruments products/technology, refer to the appropriate location: Help»Patents

in your software, the patents.txt file on your media, or the National Instruments Patent Notice

at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/

export-compliance for the National Instruments global trade compliance policy and how to

obtain relevant HTS codes, ECCNs, and other import/export data.

*325798A-01*

2. Remove the existing cable by completing steps a and b below.

Caution Do not put pressure on additional components near the connector or scrape the

connector against components while removing the cable.

a. Gently remove by hand (no tools necessary) both sides of the

cable from the mating connectors on the two boards of the

controller.

1. Disconnect one side of the flex cable from its mating

connector.

2. Straighten the cable after disconnecting the first side.

3. Disconnect the second side of the flex cable from its mating

connector.

b. Discard the old cable.

3. Install the new cable.

a. The replacement cable will be flattened when it arrives.

b. Each connector is keyed in a way to prevent improper installation.

c. Connect one side of the new flex cable to the appropriate keyed

connector on the controller.

d. Slowly bend the cable using large angles such that the second flex

cable connector is above the mating connector on the controller,

and make the connection.

Caution Tight bends or creases in the cable will damage its functionality.

e. Once both sides of the cable are in place apply moderate pressure

on both sides to ensure a good connection. Do not push on other

components in the process. You may need to gently push the

middle of the cable toward the inside of the controller to square up

the connectors on the board.

4. Verify the cable is installed correctly.

a. Install the controller into a chassis.

b. Power on the chassis.

c. Verify the controller boots properly.

Other manuals for PXI-8109

This manual suits for next models

Table of contents

Other National Instruments Controllers manuals

National Instruments

National Instruments NI PXIe-8840 User manual

National Instruments

National Instruments PXI-8119 User manual

National Instruments

National Instruments PXI-7356 User manual

National Instruments

National Instruments NI-488.2M User manual

National Instruments

National Instruments 7340 User manual

National Instruments

National Instruments cDAQ-9139 User manual

National Instruments

National Instruments RMC-8357 User manual

National Instruments

National Instruments cRIO-9064 User manual

National Instruments

National Instruments PXIe-8106 User manual

National Instruments

National Instruments PXI-8186 User manual

National Instruments

National Instruments PXI 8351 User manual

National Instruments

National Instruments IC-3173 User manual

National Instruments

National Instruments FW-7344 Instructions for use

National Instruments

National Instruments cRIO-9032 User manual

National Instruments

National Instruments CompactRIO cRIO-9066 User manual

National Instruments

National Instruments PXI-8109 User manual

National Instruments

National Instruments cRIO-9034 User manual

National Instruments

National Instruments IC-3120 User manual

National Instruments

National Instruments NI cDAQ-9134 Owner's manual

National Instruments

National Instruments 187970E-01 User manual

National Instruments

National Instruments Network Adapter NI PXIe-6672 User manual

National Instruments

National Instruments PCI-7352 User manual

National Instruments

National Instruments PXI Series User manual

National Instruments

National Instruments cRIO-9032 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual