MULTIQUIP LD6 User manual

LD6 RIDE-ON TROWEL — EDGER KIT INSTALLATION INSTRUCTIONS P/N 45718 — REV. #1 (03/05/20) — PAGE 1

LD6 Ride-On Trowel

Edger Kit Installation Instructions

The following instructions are intended to assist the user with the installation of the Edger Kit for use on a Multiquip

Ride-On Trowel model LD6. Please read all assembly instructions before installing the kit.

REQUIRED TOOLS

16 mm wrench or socket

PARTS

Verify that all parts are accounted for.

See Figure 1 and Table 1.

Table 1. LD6 Edger Kit

Item Part No. Description Qty. Remarks

1 45471 Edger Kit, LD6 1 Includes

items 2–10

2 32976 Screw, HFS M10-1.5 × 25 2

3 42353 Nut, Hex, Serrated-Flange, M10-1.5 2

4 45718 Instructions, Edger Kit, LD6 1

5 N/A Assembly, Edger Bracket,

Pre-Assembled 1Includes

items 6–10

6 0300 B Washer, Flat SAE 5/16" 2

7 15520-050 Screw, HHC M8-1.25 × 50 mm 2

8 21189 Wheel, 2.13" OD × 1.25" W 2

9 21369 Bearing, Sealed 5/16" ID × 7/8" OD 8

10 45477 Bracket W/A, Edger, LD6 1

Figure 1. LD6 Edger Kit

INSTRUCTIONS

LD6 RIDE-ON TROWEL — EDGER KIT INSTALLATION INSTRUCTIONS P/N 45718 — REV. #1 (03/05/20) — PAGE 2

WORK SAFELY!

Only a qualiﬁed service technician with proper training

should perform this installation. Follow all shop safety rules

while performing this installation.

PREPARATION

1. Make sure the trowel is turned OFF and the engine

is cool.

2. Disconnect the negative (BLACK) battery cable from

the negative (–) terminal on the battery.

PROCEDURE

1. Locate the mounting holes (Figure 2) in the belly

pan at the front of the trowel. Note that there are

three sets of holes, but only one set of holes will be

used. Whichever set of mounting holes is chosen will

determine the distance that the edger wheels extend

out from the trowel.

Figure 2. Locate Mounting Holes

MOUNTING

HOLES

1ST SET

MOUNTING

HOLES

2ND SET

MOUNTING

HOLES

3RD SET

BELLY PAN

2. Secure the edger bracket assembly to the front belly

pan using the two M10-1.5 × 25 hex ﬂange screws

(P/N 32976) and two M10-1.5 hex nuts (P/N 42353).

Choose the mounting holes that correspond to the

edging distance you prefer. See Figure 3.

Figure 3. Install Edger Bracket Assembly

EDGER BRACKET

ASSEMBLY

M10-1.5 × 25

HEX FLANGE

SCREW

P/N 32976

M10-1.5

HEX NUT

P/N 42353

BELLY PAN

LD6 RIDE-ON TROWEL — EDGER KIT INSTALLATION INSTRUCTIONS P/N 45718 — REV. #1 (03/05/20) — PAGE 3

NOTES

Your Local Dealer is:

HERE’S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

UNITED STATES

Multiquip Inc.

(310) 537- 3700

6141 Katella Avenue Suite 200

Cypress, CA 90630

E-MAIL: mq@multiquip.com

WEBSITE: www.multiquip.com

CANADA UNITED KINGDOM

Multiquip Multiquip (UK) Limited Head Ofﬁce

(450) 625-2244

4110 Industriel Boul.

Laval, Quebec, Canada H7L 6V3

E-MAIL: infocanada@multiquip.com

0161 339 2223

Unit 2, Northpoint Industrial Estate,

Globe Lane,

Dukinﬁeld, Cheshire SK16 4UJ

E-MAIL: sales@multiquip.co.uk

Multiquip Inc

and

the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property

of their respective owners and used with permission.

The information and speciﬁcations included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in

this document are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change speciﬁcations, design or the information published