MSI MS-6367 User manual

Introduction

1-1

Chapter 1. Introduction

Chapter 1. Getting Started

Thank you for purchasing the MS-6367 v1.X M-ATX mainboard. The

MS-6367 mainboard is a superior computer mainboard based on nVIDIA Crush

11 & MCP-D chipsets for optimal system efficiency. Designed to fit the ad-

vanced AMD®Duron/Athlon processors in the 462 pin package, the MS-6367

mainboard delivers a high performance and professional desktop platform

solution.

Getting Started

TOPICS

Mainboard Specification 1-2

Mainboard Layout 1-5

Quick Components Guide 1-6

All manuals and user guides at all-guides.com

all-guides.com

Chapter 1

1-2

CPU

Supports Socket A for AMD®Duron/Athlon processor

Supports 650MHz, 700MHz, up to 1.5GHz or higher

Chipset

nVIDIA®Crush 11 chipset

- AGP 4x (1.5V only)

- Supports 200/266 MHz FSB

- 64-bit / 128-bit DDR memory controller

- Integrated GeForce2 MX-class advanced Graphics Processing Unit

- LDT interface to MCP (800MB/sec max)

- Multiplex DVI / TV Interface with AGP Slot

nVIDIA®nFORCE MCP-D (Media Communications Processor)

- Dual ATA/100 controller

- USB OHCI 1.0a up to 6 ports

- IEEE 802.3 compatible MAC (MII)

- Integrated Audio Processor Unit

- AC 97 2.1 Compliant Interface

- Dolby Digital S/PDIF output function

MainMemory

Supports 2 DDR DIMM

Supports a maximum memory size of 1GB

Supports either 64- or 128-bit system memory

Slots

One AGP 2.0 4x 1.5V slot

Three 32-bit Master PCI 2.2 Slots

Supports 3.3/5V PCI bus Interface

On-BoardIDE

An IDE controller on the MCP/MCP-D chipset provides IDE HDD/CD-

ROM with PIO, Bus Master and Ultra DMA 100 operation modes.

Can connect up to four IDE devices

Mainboard Specification

All manuals and user guides at all-guides.com

Introduction

1-3

Audio

Chip integrated (6 channels audio)

APU integrated in MCP-D (Audio Processing Unit)

- Supports up to 256 hardware-processed voices or 64 hardware voices

in 3D

- Supports multi-speaker 3D audio (2/4 channel)

- S/PDIF interface (MCP-D)

Video

256-bit 3D and 2D graphics accelerator

2nd generation T & L engine, nVIDIA Shading Rasterizer-NSR

Multiplex DVI/TV interface with the AGP slot

PC2001 compliant SMA and operates with either 64-bit or 128-bit system

memory installed

Network (Optional)

Chip Integrated

- 10/100 BaseT Ethernet/Fast Ethernet

On-Board Peripherals

On-Board Peripherals include:

- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and

2.88Mbytes.

- 1 serial port (COMA)

- 1 parallel port supports SPP/EPP/ECP mode

- 6 USB ports (2 rear connectors and 2 USB front pin headers- 4 ports)

- 1 IrDA connector

- 1 Audio/Game Port

- 1 VGA Port

BIOS

The mainboard BIOS provides Plug & Play BIOS which detects the

peripheral devices and expansion cards of the board automatically.

The mainboard provides a Desktop Management Interface (DMI) func-

tion which records your mainboard specifications.

All manuals and user guides at all-guides.com

Chapter 1

1-4

Dimension

M-ATX Form Factor: 9.6 inch x 9.6 inch

Mounting

6 mounting holes

Others

LAN Wake Up function

Modem (Internal/External) Ring Wake Up function

PC99 Color Connector

All manuals and user guides at all-guides.com

Introduction

1-5

Mainboard Layout

MS-6367 Micro ATX Mainboard

Note: One unique MAC Address label is attached on PCI Slot 3 of the

motherboard that supports LAN. The label looks like the picture

below but its number varies depending on the board you purchased.

MAC Address Label

BATT

nVIDIA

nFORCE

MCP-D

DIMM2

DIMM3

J10

JGS1

JSPDIF1

ATX

Power Supply

JFP1

SOCKET 462

BIOS

PCI Slot 3

Codec

PCI Slot 2

PCI Slot 1

nVIDIA

CRUSH 11

IDE2

IDE1

Top : Parallel Port

Bottom:

COM A

VGA port

JBAT1

SW2

Top : mouse

Bottom: keyboard

Top: LAN Jack

Bottom: USB

ports

CD1

CPUFAN1

SYSFAN1

Winbond

W83627HF-AW

AUX1

To p :

Game port

Bottom:

Line-Out

Line-In

Mic

FDD1

AGP Slot

All manuals and user guides at all-guides.com

Chapter 1

1-6

Quick Components Guide

Component Function Reference

SW2 CPU FSB Selection jumper See p. 2-4

JWR1 ATX 20-pin Power Connector See p. 2-7

JKBMS1 Mouse Connector See p. 2-8

JKBMS1 Keyboard Connector See p. 2-9

USB Connectors Connecting to USB devices See p. 2-9

COM A Connecting to Serial port See p. 2-10

VGA Connector Connecting to VGA port See p. 2-10

LPT1 Parallel port connector See p. 2-11

Game/Audio Connectors Connecting to Game/Audio devices See p. 2-12

RJ-45 LAN Jack Connecting to LAN devices See p. 2-12

FDD1 Floppy disk drive connector See p. 2-13

IDE1~ IDE2 Hard disk connectors See p. 2-14

JFP1 Case connectors See p. 2-15

CD1 CD-in connector See p. 2-17

AUX1 Aux line-in connector See p. 2-17

JGS1 Power Saving Switch Connector See p. 2-17

JCASE1 Chassis intrusion switch See p. 2-18

J9 & J10 Front USB connectors See p. 2-18

CPUFAN1/SYSFAN1 Fan power connectors See p. 2-19

JSPDIF1 SPDIF Connector See p. 2-20

JAUDIO1 Front panel audio connector See p. 2-21

JBAT1 Clear CMOS jumper See p. 2-22

AGP Slot Connecting to expansion cards See p. 2-23

PCI Slots Connecting to expansion cards See p. 2-23

All manuals and user guides at all-guides.com

all-guides.com

Hardware Setup

2-1

Chapter 2. Hardware Setup

TOPICS

Central Processing Unit: CPU 2-2

Memory 2-5

Power Supply 2-7

Back Panel 2-8

Connectors 2-13

Jumpers 2-22

Slots 2-23

Hardware Setup

This chapter provides you with the information about hardware setup

procedures. While doing the installation, be careful in holding the components

and follow the installation procedures. For some components, if you install in

the wrong orientation, the components will not work properly.

Use a grounded wrist strap before handling computer components. Static

electricity may damage the components.

All manuals and user guides at all-guides.com

Chapter 2

2-2

1. Pull the lever sideways away

from the socket. Then, raise

the lever up to a 90-degree

angle.

Central Processing Unit: CPU

CPU Installation Procedures

2. Look for the cut edge. The

cut edge should point

towards the lever pivot. The

CPU will only fit in the

correct orientation.

The mainboard supports AMD®Athlon and Duron processors.

It uses a CPU socket called Socket A for easy CPU installation. Make sure

the CPU has a Heat Sink and a cooling fan attached on the top to prevent

overheating. If you do not find the Heat Sink and cooling fan, contact your

dealer to purchase and install them before turning on the computer.

Open Lever

Cut edge

Sliding

Plate

Lever

Press down

the CPU

3. Press the CPU down firmly

into the socket and close the

lever. As the CPU is likely to

move while the lever is being

closed, always close the lever

with your finger pressing

tightly on top of the CPU to

make sure the CPU is properly

& completely embedded into

the socket.

Overheating will seriously damage the CPU and system,

always make sure the cooling fan can work properly to

protect the CPU from overheating.

WARNING!

All manuals and user guides at all-guides.com

Hardware Setup

2-3

As processor technology pushes to faster speeds and higher performance,

thermal management becomes increasingly crucial when building computer

systems. Maintaining the proper thermal environment is key to reliable

operation. As such, the processor must be maintained in the specified thermal

requirements.

AMD Athlon/Duron processor with a speed of 600MHz and above re-

quires LARGER heatsink and fan. You also need to add thermal grease be-

tween the CPU and heatsink to improve heat dissipation. Then, make sure that

the CPU and heatsink are securely fastened and in good contact with each

other. These are needed to prevent damaging the processor and ensuring

reliable operation. If you want to get more information on the proper cooling,

you can visit AMDs website for reference.

WARNING! Thermal Issue for CPU

All manuals and user guides at all-guides.com

Chapter 2

2-4

CPU Core Speed Derivation Procedure

If CPUClock = 100MHz

Core/Bus ratio = 7

then CPU core speed = Host Clock x Core/Bus ratio

= 100MHzx7

= 700MHz

CPU FSB Selection Jumper: SW2

To use a 133MHz CPU, you need to set the SW2 jumper to short 1-2 pin.

To use a 100MHz CPU, set the SW2 jumper to short 2-3 pin.

SW2

FSB = 133MHz FSB = 100MHz

Overclocking

This motherboard is designed to support overclocking.

However, please make sure your components are able to

tolerate such abnormal setting, while doing

overclocking. Any attempt to operate beyond product

specifications is not recommended. We do not guarantee

the damages or risks caused by inadequate operation or

beyond product specifications.

WARNING!

All manuals and user guides at all-guides.com

Other manuals for MS-6367

Table of contents

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual