LI-COR LI-8100 User manual
LI-8100
Automated Soil CO2 Flux System
Configuring the Palm Tungsten C
for use with the LI-8100
®
2
NOTICE
The information contained in this document is subject to change without notice.
LI-COR MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. LI-COR shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
This document contains proprietary information which is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced, or
translated to another language without prior written consent of LI-COR, Inc.
© Copyright 2004, LI-COR, Inc.
Printing History: 1st Printing June, 2004
Printing History
New editions of this manual will incorporate all material since the previous editions.
Update packages may be used between editions which contain replacement and
additional pages to be merged into the manual by the user.
The manual printing date indicates its current edition. The printing date changes when
a new edition is printed. (Minor corrections and updates which are incorporated at
reprint do not cause the date to change).
LI-COR, Inc. • 4421 Superior Street • Lincoln, Nebraska 68504
Phone: 402-467-3576 • FAX: 402-467-2819
Toll-free: 1-800-447-3576 (U.S. & Canada)
E-mail: [email protected]
www.licor.com
3
Table of Contents
The 8100-560 Wireless Communication Package ................................................................ 4
Configuration Procedure ....................................................................................................... 5
Troubleshooting.................................................................................................................... 12
Enable Encryption Function .................................................................................................. 13
4
The 8100-560 Wireless Communication Package
The Palm® Tungsten™ C is the currently recommended PDA for wireless
communication with the LI-8100. LI-COR does not support other brands of
PDAs for use with the LI-8100.
The 8100-560 Wireless Communication Package includes the following:
●8100-551 Palm Tungsten C (includes 2 CDs, desktop software CD and
software essentials CD, and a cradle/charger with AC cable and USB cable)
●8100-552 Cisco Wireless Card
●8100-553 Palm RS-232 Serial Cable
●8100-555 Palm Battery Pack (Palm Power To Go)
●8100-556 Palm Universal Charger Travel Kit
●Palm/LI-8100 Configuration Instruction Manual
5
Configuration Procedure
Introduction
Before you start the configuration process, make sure the Palm Tungsten C is
fully charged.
●Connect the Palm cradle to the computer using the USB cable attached to
the cradle, and to AC power (if you are outside the United States you may
also need to use the Palm Universal Travel Kit).
●Place the Palm Tungsten C on the cradle and let it charge fully (this can
take a few minutes to a few hours).
●When done charging the Palm Tungsten C, follow the Palm software
installation process (two CDs are included).
●Next, take a few moments to familiarize yourself with the Palm Tungsten C,
if you are not already.
Configuring the Palm
To configure the Palm Tungsten C for use with the LI-8100, follow the steps
below:
1. If you have not installed the Palm software, insert the Palm Tungsten C
Desktop Software CD (CD1) into the CD-ROM drive of your computer.
Follow the instructions and complete the installation. Remove CD1.
Install CD2 (software essentials), if desired.
2. Insert the LI-8100 software CD. The screen below will appear. The
Update PC Application Software button will install the Windows software
and the Data Analysis Software (FV8100 File Viewer). To install the Palm
Application Software, click on Add Palm Application to HotSync List.
6
3. The window below will appear. Highlight the LI-8100 Palm software in
the Handheld list. The properties of the software are shown to the right
(name, size and type). Below that is displayed “Ready for HotSync
operation”.
7
4. Turn on the Palm Tungsten C. Place it on the cradle. Press the HotSync
button on the cradle. The Palm Tungsten C will load the LI-8100 Palm
software and when finished, an LI-8100 icon will appear on the screen.
5. Remove the Palm Tungsten C from the cradle.
6. Open the Analyzer Control Unit case. Remove the access cover. Install
the wireless card into either of the two PC card slots.
7. Now we will configure the LI-8100 and the Palm to communicate via a
wireless connection. First we will configure the LI-8100.
8. Connect a battery or other power supply. Turn on the LI-8100.
9. Connect the round female end of the adapter cable to the LI-8100 RS-232
port (male port). Connect the 9-pin male end of the adapter cable to the 9-
pin female end of the Palm RS-232 cable. Connect the Palm RS-232 cable
to the Palm Tungsten C.
8
10. Turn on the Palm Tungsten C. Tap the LI-8100 icon. Tap Connect by
Serial. Wait while the “Status: Querying …” message is displayed and the
“Instrument Status” screen is active.
11. Tap the top of the screen and select the 8100 menu. Select Instrument
Settings. Name the instrument (tap the space next to “Name” and use the
keypad to enter the name. Tap Send. Tap the screen next to Network
Params.
12. The new screen is named Set Network Parameters.
a. Tap next to Network Name. The Set Network Name screen
appears. Use the keypad to enter a name. If you use multiple words
with spaces, make sure you record the exact name with the
appropriate space(s), as you will use it again when you configure the
Palm Tungsten C.
9
b. Leave Security “DISABLED”.
c. Tap next to Wireless Channel and select a number (i.e., 10). You will
need to remember this number in a later step.
d. Tap next to IP Address. The Set Network IP Address screen appears
with four spaces separated by three dots.
e. Tap the space to the left and enter “192”. Tap the next space and
enter a 3-digit number. Repeat for the third and fourth spaces.
f. Record the IP Address, as you will need it again later. When done,
tap Send.
g. The Set Network Parameters screen appears again.
10
h. Next to Netmask, the numbers “255.255.255.0” should appear. (If
not, tap the space next to Netmask).
i. A new screen named Set Network Netmask appears. Type
“255.255.255.0” and tap Send.
13. Turn the LI-8100 off and then back on again. Wait for the “Ready” light
to come on.
14. Next, we will configure the Palm Tungsten C. Go to the home screen of
the Palm Tungsten C by pressing the Home key (lower right). Scroll down
the screen and tap the Prefs icon.
15. The Preferences screen appears. Under Communication, tap Network.
The new screen will read Preferences at the top left corner and Network
at the top right corner. Next to Service, Wi-Fi appears. Tap Details. A
new screen named Wi-Fi Configuration appears. Tap Wi-Fi
Preferences…
16. The new screen is called Preferences Wi-Fi. A Wi-Fi Connection Progress
message will appear briefly. The Palm will attempt to connect to the Soil
Network 1 that was established while configuring the LI-8100. Make sure
the Wi-Fi is “On”, the Network (use drop-down menu) is set to the name
you chose in step 13 above (i.e., Soil Network 1) and the Signal reads Ad-
hoc network.
Other manuals for LI-8100
1
Table of contents
Other LI-COR Measuring Instrument manuals
LI-COR
LI-COR LI-180 User manual
LI-COR
LI-COR LI-840 Guide
LI-COR
LI-COR li-7200 User manual
LI-COR
LI-COR LI-200R User manual
LI-COR
LI-COR Eddy Covariance User manual
LI-COR
LI-COR LI-830 Guide
LI-COR
LI-COR LI-250 User manual
LI-COR
LI-COR LI-3100C User manual
LI-COR
LI-COR LI-800 User manual
LI-COR
LI-COR LI-8100A User manual
LI-COR
LI-COR LI-800 Guide
LI-COR
LI-COR li-6262 User manual
LI-COR
LI-COR LI-8100A User manual
LI-COR
LI-COR LI-8150 Multiplexer Installation and operating instructions
LI-COR
LI-COR LI7200RS User manual
LI-COR
LI-COR LI-7810 User manual
LI-COR
LI-COR LI-870 Guide
LI-COR
LI-COR LI-600 User manual
LI-COR
LI-COR LI-250A User manual
LI-COR
LI-COR 4300 User manual
