LEGRAND DRD9 User manual

ADVANCED OPERATION

Groups

You can use the Group feature to control multiple Miro wireless fan controls from

one location. Binding the fan controls together in the same Group enables them to

work in exactly the same way, from any of the control locations.

You can also Group one or more Miro DRD8 Wireless Multilocation Controllers

with a single fan control to control one fan circuit from multiple locations.

You can include other Miro wireless devices in the Group. Just remember that all

devices in the Group operate when one member operates. If you group a dimmer

with a fan control, the fan speed will increase when you increase the brightness

from the dimmer. Conversely, if you press a button on the fan control to reduce the

fan speed, the lights will dim.

Set the House ID (see Set House ID) before setting up Groups.

1. Go to any device that you want to include in the Group. Press . The device

LED flashes yellow. Devices not currently in the group flash green.

You now have 5 minutes to complete this process.

2. To include or exclude a device in the Group press on the device until the

LED changes color. Yellow flashing LED = Included in the Group

Green flashing LED = NOT included in the Group

If you get to a device and it is NOT flashing, see TROUBLESHOOTING.

3. Return to the device used in step 1 and press to terminate Group binding.

All LEDs revert to solid green.

Scene Control

The Miro Wireless Fan Control may be easily incorporated into room and whole

house preset scenes. After binding the fan control to the desired scene, as

described in the scene controller installation instructions (DRD5, DRD6, MRH5G,

or MRH6G) set the fan speed by pressing one of the speed buttons or or .

Note that the DRD6 and MRH6G wireless room scene controllers’ default

operation for the E scene button and the paddle does not turn off the

DRD9 fan control. You can manually add the fan so that it is included when

“all off” function is invoked at the room scene controller.

The Miro Installation Guide provides more information about configuring scenes.

Application support information and the Miro Installation Guide are available

online.

TROUBLESHOOTING

During Set House ID, the LED is not ﬂashing on some wireless Miro devices.

• IfLEDissolidgreenbeforeinitiatingHouseIDbinding:

The device already has another House ID. Reset it to the factory default so

that it can be bound to the desired House ID. Resetting to factory defaults

is described in the “I need to start over” issue.

• IfLEDissolidyellowafterinitiatingHouseIDbinding:

The device may be out of range of the initiating device. Add a MRR2G Miro

Wireless Repeater to boost signal range.

During Binding, all LEDs stop ﬂashing before I am ﬁnished.

The binding process timer may have expired. Restart the binding process

timer by repeating steps 1 and 2 of the procedure you were using. Notice

that the devices you previously included are flashing yellow; simply finish the

process from where you left off.

The device LED ﬂashes red when I press .

If house or room scene controllers are used in the house, the house or

room configuration may be locked. Consult the installation instructions for

the DRD5 or MRH5G wireless house scene controller if one is present. See

the DRD6 or MRH6G wireless room scene controller instructions if one is

present.

I made a conﬁguration mistake. I need to start over.

You can reset any Miro wireless device to factory default settings by pressing

and holding until the LED changes to solid yellow (approximately 10

seconds). During the process, the LED flashes yellow and when complete,

it changes to solid yellow. The device can then be reconfigured, exactly like

any new device (see the Set House ID section).

The fan control does not work and the status LED is ﬂashing red

• at2Hz(10timesin5seconds):

The fan control has detected an overload condition and has shut down.

To clear the fault condition, tap and wait for the LED to turn green.

Disconnect loads in excess of rated load and try again.

• at3Hz(15timesin5seconds):

The fan control has detected a short-circuit condition and has shut down.

To clear the fault condition, tap and wait for the LED to turn green.

Remove power, rectify the short-circuit, restore power, and try again.

The status LED is off.

Check the paddle position. If the bottom edge is recessed, the Air Gap safety

feature is engaged. See Fan Maintenance.

CLEANING

Clean using a cloth dampened only with water and a little mild detergent. Use of

solvents or hydrocarbon-based cleaners may cause permanent damage.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmenttoanoutletonacircuitdifferentfromthattowhichthe

receiver is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Caution:Anychangesormodicationstothisdevicenotexplicitlyapprovedby

the manufacturer could void your authority to operate this equipment.

WARRANTY INFORMATION

Manufacturer warranties its products to be free of defects in materials and

workmanshipforaperiodofve(5)years.Therearenoobligationsorliabilities

on the part of manufacturer for consequential damages arising out of, or

in connection with, the use or performance of this product or other indirect

damageswithrespecttolossofproperty,revenueorprot,orcostofremoval,

installation or reinstallation.

Please

Recycle

1061 South 800 East

Orem, UT 84057

Phone:800.555.9891

www.vantagecontrols.com

Legrand Customers contact: Vantage Customers contact:

05761r209/07

301 Fulling Mill Road Suite G

Middletown, PA 17057

Phone:800.321.2343

www.legrand.us/onq

DRD9

Wireless Fan Control

Specifications

Voltage 120VAC,60Hz

Operating Temperature.................32°F to 104°F (0°C to 40°C)

Maximum Load Rating....................................................... 1.5A

Load Type Compatibility.............. Up to two ceiling fan motors

Installation Instructions

U.S. Patent 6,175,220. Other utility,

design, and foreigh patents pending.

UNIT DESCRIPTION

The Miro Decorator DRD9 Wireless Fan Control conveniently offers silent,

one-touch control of one or two ceiling paddle fans, with a combined current

rating up to 1.5 amps. The DRD9 has five buttons to provide 4 speed controls,

plus off. One touch of the rocker paddle can also turn the fan off, or turn it on

and resume the most recently used speed.

Miro Wireless

Miro wireless devices use radio signals to communicate with each other

to control lighting and other types of electric loads in selected areas. They use

the900MHzbandforhigh-speedcontrolcommunication.Usingthepatented

“frequency-agile” Top Dog™ technology, Miro wireless devices

avoidinterferencewithother900MHzdevices,suchascordlessphones

and baby monitors.

INSTALL IN COMPLIANCE WITH ALL APPLICABLE

CODES & STANDARDS.

Failure to follow these instructions may cause

personal injury or equipment damage.

CAUTION

THIS UNIT IS EXCLUSIVELY DESIGNED FOR USE WITH CEILING FANS.

Do not use to control lighting, receptacles

or transformer-operated devices.

Do not use for a fan and a light wired together on the same load wire.

Do not wire in the same circuit as a GFCI circuit breaker or receptacle.

INSTALLATION

For ease of installation, manufacturer recommends use of a deep wall box.

1. Disconnect power to circuit by turning circuit breaker OFF before

installation.

2. Remove existing wall plate and switch.

3. Stripexistingwires1/2”.

4. Connect the supply and load ground wires to the GND terminal on the

back of the unit.

5. Connect the white (Neutral) fan control wire to the white supply and white

load wires, using a wire nut.

6. Connect the black fan control wire to the black supply Line, using a

wire nut.

7. Connect the red fan control wire to the black load wire, using a wire nut.

8. Attach the wall plate.

9. Switch the circuit breaker back ON.

CAUTION

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE FAN CONTROL.

SET HOUSE ID

All Miro wireless devices installed in the same home must acquire the same

unique House ID before use. This process is known as house binding. Each

Miro wireless device is bound to all other Miro wireless devices in the house.

New Installation

1. Withalldevicesinstalledandenergized,makesurethateveryMirowireless

device LED is yellow. If any LED is off, be sure the circuit breaker is on and

the device is correctly installed.

2. Press on any device paddle

until the LED ﬂashes yellow

(about 2 seconds). This indicates

that it has acquired a unique

House ID.

3. Make sure that all other Miro

wireless device LEDs are ﬂashing

green, indicating that they have

acquired the same House ID.

4. Return to the device used in step 2, which is still ﬂashing yellow. Press

until the LED changes to solid green (about 2 seconds). All device LEDs in

the house change to solid green, indicating house binding is complete.

Adding a Device to an Existing Installation

If you’re adding or replacing a device in a Miro wireless installation that is

already operating, the new device must acquire the same House ID as the

other Miro wireless devices in the house. After the new device is powered up,

the LED should be solid yellow. This indicates that it has not yet acquired a

HouseID.ToacquiretheHouseIDfortheexistingsystem:

1. Press on any previously bound device until the LED ﬂashes yellow (about

2 seconds).

2. VerifythatthenewlyaddeddeviceLEDisashinggreen,indicatingthatit

has acquired the House ID.

3. Return to the same previously bound device used in step 1 and press until

the LED changes to solid green (about 2 seconds). All device LEDs should

now be solid green.

When you see

in the instructions,

firmly press and

hold both the top

and bottom of the

device paddle until

the LED changes

(about 2 seconds).

OPERATION

Beforeuse,setthefantorunintheappropriatedirectionandatfullspeed:

1. Press the top speed button on the DRD9 wireless fan control, and wait to

allow the fan motor to run up to full speed.

2. Using the controls on the fan (typically pull-chains), adjust so that the fan is

running at full speed, and in the desired direction. The pull chains may now

be removed or shortened.

Button and Paddle Functions

The DRD9 wireless fan control has a rocker paddle

andvespeedcontrolbuttons.Usethespeedbuttons

to select an appropriate fan speed or OFF.

Rocker paddle functions are described below.

When you see

touch the top

of the paddle as

directed.

Fastest

Slowest

OFF

The wireless fan control may feel warm to the touch during normal operation.

Fan Maintenance

When fan maintenance is required, use the Air Gap Isolation feature for safety.

Toactivatethefeature:

Press FIRMLY, so that the paddle clicks and latches in. Make sure the

status LED is extinguished, indicating that the load is isolated.

To release and return to normal operation, press .

Power Fail Memory

After a power failure, all Miro devices automatically return to the state they

were in immediately prior to loss of power.

Tap once Turn fan ON and resume the last used speed

Tap twice Full speed

– – Press and hold Increase the speed

Tap once Turn fan OFF

– – Press and hold Decrease the speed

When you see

touch the

bottom of the

paddle as

directed.

4-FOLD

•Print:2-sides

•InkColor:Black

•Paper:White16lb(60g/msq)

Uncoated, prefer recycled stock

•Finaltrimsize:16”(Wide)x6”(High).

•Four(4)fold.

•Finalfoldedsize:4”(Wide)x6”(High).

TITLE BOX PAGE ONLY.

DO NOT MAKE FILM • DO NOT PRINT

SANTA CLARA, CALIFORNIA

Title: DRD9 Installation Instructions

IFYOUHAVEANYQUESTIONSREGARDINGSPECIFICATIONSORREQUIRE

ADDITIONAL FILE FORMATTING, PLEASE CONTACT Mary Jo Sowinski.

Phone:408-486-7511

Email:[email protected]

Drawing #:

05761

Orig. Drawing Date: 10 AUG 06 Rev. #:

Revision Date: 25 SEP 07

REVEL

Scale: 1:1

All information in this drawing is the property of Watt Stopper/Legrand and cannot be copied or

used without the written approval of Watt Stopper/Legrand.

Drawn by

PLM

MarCom

Engineering

TITLE BOX PG

REV DESCRIPTION INT: REV. DATE APPROVED

1 ECO#C01694 MJS 3/31/04 CG

2 EC0# C02414 DR

Table of contents

Other LEGRAND Controllers manuals

LEGRAND

LEGRAND 0 675 97 User manual

LEGRAND

LEGRAND Mosaic 335 25 User manual

LEGRAND

LEGRAND 0 035 40 User manual

LEGRAND

LEGRAND radiant User manual

LEGRAND

LEGRAND ADMHRM4 User manual

LEGRAND

LEGRAND Celiane Series Quick start guide

LEGRAND

LEGRAND HA7000 User manual

LEGRAND

LEGRAND Raritan SRC-0100 User manual

LEGRAND

LEGRAND 0 488 64 User manual

LEGRAND

LEGRAND Wattstopper DCLV2 Service manual

LEGRAND

LEGRAND ALPTEC 5.2 User manual

LEGRAND

LEGRAND Raritan SRC-0100 User manual

LEGRAND

LEGRAND Raritan Smart Rack Controller User manual

LEGRAND

LEGRAND 026 21 User manual

LEGRAND

LEGRAND 0 663 40 User manual

LEGRAND

LEGRAND Wattstopper LMJA-8125-SM User manual

LEGRAND

LEGRAND 5 720 89 User manual

LEGRAND

LEGRAND Wattstopper LMRC-111-16M User manual

LEGRAND

LEGRAND Arteor User manual

LEGRAND

LEGRAND Axiom User manual

LEGRAND

LEGRAND 0 676 46 User manual

LEGRAND

LEGRAND 5739 04 Instruction Manual

LEGRAND

LEGRAND F401 User manual

LEGRAND

LEGRAND Wattstopper DLM LMJA-8 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual