LEGRAND MRD6 v2 User manual

MRD6 v2

Wireless Room Scene Controller

Specifications

Operating Voltage.........................................120/277VAC, 60Hz

Operating Temperature.................32°F to 104°F (0°C to 40°C)

Patents pending

Installation Instructions

UNIT DESCRIPTION

The Miro MRD6 Wireless Room Scene Controller is a room level scene controller.

It provides instant recall of ﬁve user-recorded lighting scenes (or presets)

assigned to a room or designated area. It also provides off and on functions and

overall control of the room’s light level.

The MRD6 is mounted inside a wall box and framed by an

architectural screwless Miro wall plate (required and sold

separately). It can be identiﬁed by the icon on its front, which

resembles the outline of a door leading to a room.

The Miro wireless room scene controller works as part of a Miro

wireless system. It can control a variety of Miro wireless devices including

dimmers, switches, plug-in appliance modules and plug-in lamp modules.

You can control up to ﬁfteen scenes in the room (see MORE SCENES section). You

can install additional room scene controllers or MRH6 room scene remotes to

control those scenes from multiple locations.

Note: To control the entire house, use a Miro wireless house scene controller (a

wall mounted MRD5 or a handheld MRH5 remote).

Miro Wireless

Miro wireless devices use radio signals to communicate with each other to

control lighting and other types of electric loads in selected areas. They use the

900MHz band for high-speed control communication. Using the Watt Stopper’s

own “frequency-agile” Top Dog™ technology, Miro wireless devices avoid

interference with other 900MHz devices, such as cordless phones and baby

monitors.

Application Assistance

The Miro Installation Guide provides more information about conﬁguring scenes.

Instructions for installation and use are included with the relevant Miro wireless

devices. Application support information and the Miro Installation Guide is

available online.

LINE

GND

Supply

Wires

NEUT

Wire Legend

Ground

Line

Neutral

INSTALLATION

1. Disconnect power to circuit by turning circuit breaker OFF.

2. Remove existing cover plate and switch.

3. Temporarily attach the steel subplate for the Miro

cover plate to the wall box.

4. Pull the wiring through the new Miro subplate.

5. Strip existing wires 1/2”. If two wires will be

connected to the same terminal on a Miro device, both

wires must be the same gauge (12AWG or 14AWG).

6. Wire the LINE (black), NEUTRAL (white) and GND (green or bare) supply

wires to the correspondingly marked screw terminals, according to the wiring

diagram below.

7. Using the instructions provided with the Miro cover plate, attach the MRD6 to

the metal subplate and to the wall box, then attach the Miro cover.

8. Switch the circuit breaker back ON.

CAUTION

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE DEVICE.

Install only using a UL Listed Miro cover plate and subplate

assembly. If you do not have the proper Miro subplate for your

application, obtain one from any supplier of Miro devices.

INSTALL IN COMPLIANCE WITH

ALL APPLICABLE CODES &

STANDARDS.

Failure to follow these

instructions may cause personal

injury or equipment damage.

Steel

subplate

Wall box

SET HOUSE ID

All Miro wireless devices installed in the same home must acquire the same

unique House ID before use. This process is known as house binding. Each Miro

wireless device is bound to all other Miro wireless devices in the house.

New Installation

1. With all devices installed and energized, make sure that every Miro wireless

device LED is yellow. If any LED is off, be sure the circuit breaker is on and the

device is correctly installed.

2. Press on any device paddle until

the LED ﬂashes yellow (about 2

seconds). This indicates that it has

acquired a unique House ID.

3. Make sure that all other Miro

wireless device LEDs are ﬂashing

green, indicating that they have

acquired the same House ID.

4. Return to the device used in step 2, which is still ﬂashing yellow. Press

until the LED changes to solid green (about 2 seconds). All device LEDs in the

House change to solid green, indicating house binding is complete.

Adding an MRD6 to an Existing Installation

If you’re adding or replacing a MRD6 in a Miro wireless installation that is

already operating, the new MRD6 must acquire the same House ID as the other

Miro wireless devices in the house. After the new MRD6 is powered up, the LED

should be solid yellow. This indicates that it has not yet acquired a House ID. To

acquire the House ID for the existing system:

1. Press on any previously bound device until the LED ﬂashes yellow (about 2

seconds).

2. Verify that the newly added MRD6 LED is ﬂashing green, indicating that it has

acquired the House ID.

3. Return to the same previously bound device used in step 1 and press until

the LED changes to solid green (about 2 seconds). All device LEDs should now

be solid green.

When you see

in the instructions,

firmly press and

hold both the top

and bottom of

the paddle until

the LED changes

(about 2 seconds).

When you see in the

instructions, touch

the top of the paddle

as directed.

When you see in the

instructions, touch the

bottom of the paddle

as directed.

ROOM BINDING

After the House ID is set in the MRD6, you create a room by binding devices to

the MRD6. You can also add the MRD6 to an existing room. When a new MRD6 is

added to a room, its scene buttons execute the same scenes as other room scene

controllers with the same scene set assignment (see MORE SCENES). Paddle

functions are the same at every room scene controller that is bound to the same

room, regardless of scene set assignment.

IMPORTANT: If you are planning to use Groups in the room, you should bind

those devices together before beginning the room binding process. Group

binding instructions are provided with individual devices.

Binding a New Room

1. With all devices installed and energized, make sure that every Miro wireless

device LED in the room is green.

2. Press on the MRD6 until its LED ﬂashes yellow (about 2 seconds). You now

have 5 minutes to complete this process.

3. To include or exclude a device press on the device until the LED changes

color.

Yellow ﬂashing LED = Included in room

Green ﬂashing LED = NOT included in room

If a device is NOT ﬂashing, see TROUBLESHOOTING.

4. Return to the MRD6 used in step 2. Press for about 2 seconds — the status

LED stops ﬂashing, then all the status LEDs in the house turn green.

Adding an MRD6 to an Existing Room

If you’re adding an MRD6 in a room where room level scene control is already

operating, the new MRD6 must ﬁrst acquire the House ID (see Adding an MRD6

to an Existing Installation). Then it must be bound to the existing room as follows:

1. Press on any previously bound MRD6 room controller or MRH6 room

remote in the room until the LED ﬂashes yellow (about 2 seconds).

2. Verify that the new MRD6 LED is ﬂashing green. All other devices included in

the room are ﬂashing yellow. Press on the new MRD6 until its LED changes

color.

Yellow ﬂashing LED = Included in room

Green ﬂashing LED = NOT included in room

3. Return to the same previously bound MRD6 used in step 1 and press until

the LED changes to solid green (about 2 seconds). All device LEDs should be

solid green.

STANDARD OPERATION

The MRD6 is shipped with most functions preprogrammed for ease of installation

and initial use. This section summarizes the default operation of the MRD6.

To make changes from this standard operation, such as changing light levels

and including or excluding devices from speciﬁc scenes, see CUSTOMIZING

OPERATION.

Paddle Functions

Use the rocker paddle to begin and end binding functions. It also functions as

an On/Off switch and a master light level Raise/Lower control for the room.

All devices bound to the same room as the MRD6 are included in the paddle

operation (except fan controls).

Scene Button Functions

The smaller buttons, labeled A—E in the illustrations, are used to record and

recall scenes. Labels are provided so that you can name these buttons to suit

your application. All devices bound to the same room as the MRD6 are included in

each scene button (except fan controls).

The following illustration shows the default operation for scene set 1-5.

NOTES:

1 Pressing and holding the paddle does not affect the operation of switched

devices. They will maintain their present state.

2 If the lights were turned off using the default E scene button or any

customized scene button programmed for 0%/ALL OFF, pressing and holding

will not raise the light level. It will raise the light level if the lights were

turned off by tapping .

3 Scene buttons on MRD6 controllers with scene set 6-10 or 11-15 are

preprogrammed to turn off all room devices.

Tap once: Raise all room

devices to 100% (ON)

Press and hold: Raise the

current scene’s level 1, 2

Press and hold: Lower the

current scene’s level 1

Tap once: Lower all room

devices to 0% (OFF)

Tap once: All room

Dimmers / Switches

to to

100% ON

75% ON

50% ON

25% ON

0% OFF

Press and hold:

Saves the current

device settings as

the scene that is

recalled the next tim

you tap this button.

See CUSTOMIZING

OPERATION.

Paddle Scene Buttons3

CUSTOMIZING OPERATION

Modify and Save the Light Levels of a Scene

1. Change lighting levels as desired by pressing or on individual devices.

2. Press and hold the scene button until the LED ﬂashes (about 2 seconds) to

save the new settings.

Removing or Adding Devices to a Scene

1. Press on the MRD6 until the LED begins ﬂashing (about 2 seconds).

2. Press the scene button that you wish to program. LEDs on all wireless Miro

devices begin to ﬂash. You now have 5 minutes to complete this process.

3. To include or exclude a device in the scene press on the device until the LED

changes color. Yellow ﬂashing LED = Included in the active scene

Green ﬂashing LED = NOT included in the active scene

If a device is NOT ﬂashing, see TROUBLESHOOTING.

NOTE: You must include devices that are off in the room scene if you want

them to turn off when that scene is recalled.

4. Return to the MRD6 used in step 1. Press for 2 seconds — the status LED

stops ﬂashing, then all the status LEDs in the house turn green.

Removing or Adding Devices to the Paddle “On” Function

1. Press on the MRD6 until the LED begins ﬂashing (about 2 seconds).

2. Tap the paddle on the MRD6. The LEDs on all the Miro wireless devices

begin to ﬂash. You now have 5 minutes to complete this process.

3. To include or exclude a device press on the device until the LED changes

color. Yellow ﬂashing LED = Included in paddle operation

Green ﬂashing LED = NOT included in paddle operation

If a device is NOT ﬂashing, see TROUBLESHOOTING.

4. Return to the MRD6 used in step 1. Press for about 2 seconds — the status

LED stops ﬂashing, then all the status LEDs in the house turn green.

5. To test, tap on any room scene controller that is bound to the same room to

switch included devices to on (dimmers go to full bright).

Removing or Adding Devices to the Paddle “Off” Function

1. Press on the MRD6 until the LED begins ﬂashing (about 2 seconds).

2. Tap the paddle on the MRD6. The LEDs on all the Miro wireless devices

begin to ﬂash. You now have 5 minutes to complete this process.

3. See step 3 above.

4. See step 4 above.

5. To test, tap on any room scene controller that is bound to the same room to

switch or fade included devices to off (dimmers go to 0%)

MORE SCENES

Up to 15 scenes are available per room. Each room level controller can access

a set of 5 scenes. The MRD6 is assigned to scenes 1-5 when shipped. Changing

to scene set 6-10 lets you record 5 more scenes; changing to scene set 11-15

lets you record another 5 scenes. Binding three room level controllers (MRH6 or

MRD6) to the room and assigning each to a different scene set, lets you dedicate

a controller to each scene set. You can bind more room scene controllers to the

room to control the same scenes from multiple locations.

All room scene controllers that have the same scene set assignment operate

the 5 scenes in the same way as all other room scene controllers programmed

for the same set. Scene buttons on controllers with scene sets 6-10 and 11-15

default to 0%/All room devices OFF. Use ROOM BINDING and CUSTOMIZING

OPERATION procedures to set up the additional scene controllers.

To assign scenes 6-10, simultaneously press

and Buntil the LED blinks twice (about 2 seconds).

To assign scenes 11-15, simultaneously press

and Cuntil the LED blinks twice (about 2 seconds).

To change the assignment back to scenes 1-5,

simultaneously press and button Auntil the LED

blinks twice (about 2 seconds).

A= 1-5 (default) B= 6-10 C= 11-15

LOCK ROOM CONFIGURATION

The Lock Conﬁguration function operates from a wireless Miro room level

controller, and prevents the Miro wireless devices in the room from being

reprogrammed. Other operations such as dimming, switching and scene recall

are not affected.

When the conﬁguration is locked, if is pressed and held on any Miro wireless

device, the device’s LED ﬂashes red and the command is ignored.

To lock the conﬁguration:

Go to any room scene controller. Simultaneously press

and buttons Band Euntil the LED ﬂashes (about 2

seconds) to toggle in and out of Lock Conﬁguration.

• If the mode changes from unlocked to locked,

the LED ﬂashes red for 2 seconds, indicating that

conﬁguration is now locked.

• If the mode changes from locked to unlocked, the

LED ﬂashes green for 2 seconds, indicating that

conﬁguration is now unlocked.

Assigning the MRD6

for scene set 6-10

TROUBLESHOOTING

During house ID binding, the LED is not ﬂashing on some devices.

• If LED is solid green before initiating house ID binding:

The device already has another house ID. Reset it to the factory default so

that it can be bound to the desired house ID. Resetting to factory defaults is

described in “I made a conﬁguration mistake. I need to start over.”

• If LED is solid yellow after initiating house ID binding:

The device may be out of range of the initiating device. Add a MRR2

Wireless Repeater to boost signal range.

During binding or customizing, all LEDs stop ﬂashing before I press .

The 5 minute binding process timer may have expired. Restart the timer by

repeating steps 1 and 2 of the procedure you were using. Notice that the devices

you previously excluded are ﬂashing green; those included are ﬂashing yellow;

simply ﬁnish the process from where you left off.

The device LED ﬂashes red when I press .

The house or room conﬁguration may be locked.

Go to any house level scene controller and simultaneously press and buttons

B and E until the scene controller LED ﬂashes GREEN.

Go back to the previously locked device and press .

• If it ﬂashes green or yellow, you have unlocked the house conﬁguration.

• If the device still ﬂashes red, the conﬁguration may be locked

by a room level scene controller such as the MRD6 or MRH6.

Go to the room scene controller and simultaneously press and buttons

B and E until the scene controller LED ﬂashes GREEN. (See LOCK ROOM

CONFIGURATION.)

Go back to the previously locked device and press .

• If it ﬂashes green or yellow, you have unlocked the room conﬁguration.

• If the device still ﬂashes red, the conﬁguration may be locked

by another room level scene controller in the house. Repeat the procedure

from different controllers until the device is no longer ﬂashing red.

I made a configuration mistake. I need to start over.

To reset any Miro wireless device to factory default settings, press and hold

- - until the LED changes to solid yellow (approximately 10 seconds).

During the process, the LED ﬂashes yellow. When complete, it becomes solid

yellow. The device can then be reconﬁgured, exactly like any new device.

CLEANING

Clean only using a cloth dampened with water and a little mild detergent. Use of

solvents or hydrocarbon-based cleaners may cause permanent damage.

POWER FAIL MEMORY

After a power failure, all Miro devices automatically return to the state that they

were in immediately prior to loss of power. All house binding and scene control

information is preserved.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by

manufacturer could void your authority to operate this equipment.

WARRANTY INFORMATION

Manufacturer warranties its products to be free of defects in materials and

workmanship for a period of ﬁve (5) years. There are no obligations or liabilities

on the part of manufacturer for consequential damages arising out of, or

in connection with, the use or performance of this product or other indirect

damages with respect to loss of property, revenue or proﬁt, or cost of removal,

installation or reinstallation.

2800 De La Cruz Blvd.

Santa Clara, CA 95050

Phone: 800.879.8585

www.wattstopper.com

Please

Recycle

1061 South 800 East

Orem, UT 84057

Phone: 800.555.9891

www.vantagecontrols.com

08532r2 9/2007

Watt Stopper Customers contact: Vantage Customers contact:

Table of contents

Other LEGRAND Controllers manuals

LEGRAND

LEGRAND 0 026 72 User manual

LEGRAND

LEGRAND 0 698 19L User manual

LEGRAND

LEGRAND 488 43 User manual

LEGRAND

LEGRAND Valena Allure Series User manual

LEGRAND

LEGRAND Adorne LC7001 User manual

LEGRAND

LEGRAND 0 488 64 User manual

LEGRAND

LEGRAND DPX3-I 1600 User manual

LEGRAND

LEGRAND 0 676 46 User manual

LEGRAND

LEGRAND Mosaic 335 25 User manual

LEGRAND

LEGRAND adorne WNAL33/43 User manual

LEGRAND

LEGRAND 0 648 84L User manual

LEGRAND

LEGRAND Celiane 670 89 User manual

LEGRAND

LEGRAND HD4657M3 User manual

LEGRAND

LEGRAND Adorne LC7001 User manual

LEGRAND

LEGRAND Pro 21 User manual

LEGRAND

LEGRAND 0 677 886L User manual

LEGRAND

LEGRAND Wattstopper DCLV2 Service manual

LEGRAND

LEGRAND 026 21 User manual

LEGRAND

LEGRAND 038 09 Quick start guide

LEGRAND

LEGRAND C2G 29977 User manual

LEGRAND

LEGRAND airQast User manual

LEGRAND

LEGRAND Wattstopper DLM LMJA-8 Series User manual

LEGRAND

LEGRAND Wattstopper LMRC-101 User manual

LEGRAND

LEGRAND 0 663 36 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual