Kobold DUC-ZUWD User manual

Table of contents

Other Kobold Measuring Instrument manuals

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

DUC-ZUWD Quickstart

Prepare your wall thickness gauge /Keypad definition

The delivery is usually ready to use; batteries (AA).

Switch on / off Backlight on / off Scroll down /

decrease

Exit Menu / Select

Enter Calibration Scroll up/

Increase

3 steps to parameterize your wall thickness gauge

1. Please check if the sensor probe type is set correctly (standard type ‘N07’)

2. Make calibration using integrated calibration sample

3. Set value for speed of sound of your pipe material.

4. Place probe on the pipe and get reading for wall thickness

Please make sure to put some coupling grease on the sensor tip before measurement.

Calibration should be repeated each time you start new measurement.

Calibration should be done at speed of sound of 5920 m/s

Put some coupling grease (Magnalube) on the probe tip (Pic.1).

Put sensor on the integrated calibration sample (Pic.2) which you find in

the lowermost right corner of the instrument.

Press button . Display will show 4.00 mm. Remove the probe.

Your DUC-ZUWD is now calibrated. Now set the speed of sound of media

of pipe material. Press button (4x) to go to menu for setting of speed

of sound. (lowermost line, right corner), see pic.3.

The value can be changed by using buttons . Values for typical

materials can be obtained from the adjacent table. Put sensor tip on your pipe

and take readings from display, see pic.4.

Connect

the signal

cables of

the

transducer

to the

thickness

gauge

Calibration sample

Pic. 1

Pic. 2

Pic. 3

Pic. 4

The instruction manuals on our website www.kobold.com are always for currently manufactured

version of our products. Due to technical changes, the instruction manuals available online may not

always correspond to the product version you have purchased. If you need an instruction manual that

corresponds to the purchased product version, you can request it from us free of charge by email

(info.de@kobold.com) in PDF format, specifying the relevant invoice number and serial number. If you

wish, the operating instructions can also be sent to you by post in paper form against an applicable

postage fee.

Disposal

Note!

•Avoid environmental damage caused by media-contaminated parts

•Dispose of the device and packaging in an environmentally friendly manner

•Comply with applicable national and international disposal regulations and

environmental regulations.

Batteries

Batteries containing pollutants are marked with a sign consisting of a crossed-out garbage can

and the chemical symbol (Cd, Hg, Li or Pb) of the heavy metal that is decisive for the

classification as containing pollutants:

Cd1Hg2Pb3Li4

1. „Cd" stands for cadmium

2. „Hg" stands for mercury

3. „Pb" stands for lead

4. „Li" stands for lithium

Electrical and electronic equipment

Manufactured and sold by:

Kobold Messring GmbH

Nordring 22-24

D-65719 Hofheim

Tel.: +49 (0)6192-2990

Fax: +49(0)6192-23398

E-Mail: info.de@kobold.com

Internet: www.kobold.com

Version K02/0722