Kichler Lighting Bead User manual

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

54" Bead LED

KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES …………………………………………………………………………....4

TOOLS REQUIRED …………………………..………………………………..………...5

PACKAGE CONTENTS ……………….....................……………………………....5

MOUNTING OPTIONS ………….................................................................6

HANGING THE FAN ……………………………………………………………………...7

INSTALLATION OF SAFETY SUPPORT …………................................8

ELECTRICAL CONNECTIONS…………..................................................9

FINISHING THE MOTOR INSTALLATION….....................................10

ATTACHING THE FAN BLADES…......................................................…11

INSTALLING THE SWITCH HOUSING…........................................….11

INSTALLING THE LIGHT KIT AND GLASS..............................……..12

OPERATING INSTRUCTIONS …………………………...........……………... 15

TROUBLESHOOTING …………………………..................………………………16

FCC INFORMATION ......………………………………………………………..........17

54" Bead LED | 3

4 | KICHLER.COM

SAFETY RULES

READ AND SAVE THESE INSTRUCTIONS

CAUTION – RISK OF SHOCK – Disconnect Power at

the main circuit breaker panel or main fuse box before

starting and during the installation.

WARNING:WARNING: This fixture is intended for installation in

accordance with the National Electrical Code (NEC) and

all local code specifications. If you are not familiar with

code requirements, installation by a certified electrician is

recommended.

WARING:WARING: To reduce the risk of fire or electric shock, use

only the control provided with the fan.

WARNING:WARNING: To reduce the risk of fire, electric shock, or

Personal Injury, mount directly to a structural framing

member or to an outlet box marked “Acceptable For

Fan Support of 15.9kg(35 lbs) or less”. For outlet box

mounting, use mounting screws provided with the outlet

box.

WARNING:WARNING: Chemical Burn Hazard. Keep batteries away

from children. This remote contains a lithium button cell

battery. If a new or used lithium button/coin cell battery is

swallowed or enters the body, it can cause severe internal

burns and can lead to death in as little as 2 hours. Always

completely secure the battery compartment. If the

battery compartment does not close securely, stop using

the product, remove the batteries, and keep it away from

children. If you think batteries might have been swallowed

or placed inside any part of the body, seek immediate

medical attention. Dispose of cells properly and keep

away from children. Even used cells may cause injury.

WARNING:WARNING: Do not operate reversing switch while fan

blades are in motion. Fan must be turned off and blades

stopped before reversing blade direction.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other

items, be cautions when working around or cleaning the

fan.

Make sure the installation site you choose allows a

minimum clearance of 7 feet from the blades to the floor

and at least 30 inches from the ends of the blades to any

obstruction.

Do not use water or detergents when cleaning the fan or

fan blades. A dry dust cloth or lightly dampened cloth will

be suitable for most cleaning.

After making the electrical connections, spliced

conductors should be turned upward and pushed carefully

up into outlet box. The wires should spread apart with the

ground wire and white(common) wire to one side with the

black (load) wire to the other side of the outlet box.

Electrical diagrams are for reference only. Light kits that

are not packed with fan must be ETL Listed and marked

suitable for use with the model fan you are installing.

Switches must be ETL General Use Switches. Refer to the

instructions packaged with the light kits and switches for

proper assembly.

10.

11.

12.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY. DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT

INSERT OBJECTS IN THE PATH OF THE BLADES.

TOOLS REQUIRED

PACKAGE CONTENTS

Phillips screwdriver

Blade screwdriver

11 mm wrench

Step ladder

Wire cutters

Unpack your fan and check the contents . You should have the following items:

A. Motor Assembly

B. Fan Blade (3)

C. Switch Housing

D. Light Kit

E. Glass

F. Remote Control Kit

G. Package hardware

1) Mounting hardware :

Wire Connector (3)

2)Blade attachment hardware :

Screws (9) , Washers (9)

3) Safety cable hardware :

Wood screw (1) ,Spring washer (1),

Flat washer (1)

54" Bead LED | 5

X2 X2

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation ) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up to

50 lbs). Do not use plastic outlet boxes.

Figure 1 and 2 are examples of dierent ways to mount the outlet box.

NOTE:NOTE: Depending on the location you have selected for installation,

you may need to purchase and install a “Joist Hanger” for the support

of the outlet box. Make sure the joist hanger you purchase has been

designed for use with ceiling fans. (Fig.3)

Outlet box

Fig. 2

Fig. 3

Fig. 1

Outlet box

HANGING THE FAN

REMEMBERREMEMBER to turn off the power before you begin installation. This is

necessary for your safety and also the proper programming of the control

system. To properly install your ceiling fan, follow the steps below.

Step 1.Step 1. Loosen two (one of each across) of the four screws from the ceiling

mounting bracket, and remove the other two and keep for later use, then

release the ceiling mounting bracket from the motor assembly. (Fig. 4)

Step 2.Step 2. Before attaching fan to outlet box (not included), ensure the outlet

box is securely fastened to at least two points to a structural ceiling member

(a loose box will cause the fan to wobble). Pass the 120 volt supply wires from

the ceiling outlet box through the center of the ceiling mounting bracket.

Install mounting bracket to outlet box in ceiling using the screws and washers

included with the outlet box. (Fig. 5)

Step 3.Step 3. Hook the motor body onto the ceiling mounting bracket as shown.

You can now proceed with the electrical wiring of your fan. (Fig. 6)

Fig. 4

Fig.6

Fig. 5

54" Bead LED | 7

Ceiling Mounting

Bracket

Listed Outlet Box

Ceiling Mounting Bracket

Flat Washer

Screw

Hook

Motor Assembly

Motor

Assembly

8 | KICHLER.COM

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from failing,A safety support cable is provided to help prevent the ceiling fan from failing,

please install it as follows.please install it as follows.

Step 1.Step 1. Drive a wood screw and washers into the side of the brace that holdsDrive a wood screw and washers into the side of the brace that holds

the outlet box. Leave 3mm (1/8") of space between the support brace andthe outlet box. Leave 3mm (1/8") of space between the support brace and

the washer. (Fig. 7)the washer. (Fig. 7)

Step 2.Step 2. Insert the safety cable through the mounting bracket and one of theInsert the safety cable through the mounting bracket and one of the

holes in the outlet box into the ceiling. Adjust the length of the safety cableholes in the outlet box into the ceiling. Adjust the length of the safety cable

to reach the screw and washers by pulling the extra cable through the cableto reach the screw and washers by pulling the extra cable through the cable

clamp until the overall length is correct, put the end of the cable back throughclamp until the overall length is correct, put the end of the cable back through

the cable clamp, forming a loop at the end of the cable. Tighten the cablethe cable clamp, forming a loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the safety cable over theclamp securely. Now, put the loop in the end of the safety cable over the

wood screw and under the washer. Tighten the wood screw securely.wood screw and under the washer. Tighten the wood screw securely.

(Fig. 8)(Fig. 8)

NOTE:NOTE: Although the safety support cable is required for CanadianAlthough the safety support cable is required for Canadian

installations only. It’s a good idea to make the attachment with anyinstallations only. It’s a good idea to make the attachment with any

installation.installation.

Flat Washer

Support Brace

Wood screw

Spring Washer

Safety Cable

Bolt Wood Screw

Outlet Box

Ceiling

Fig. 7

Fig. 8

54" Bead LED | 9

MAKE THE ELECTRICAL CONNECTIONS

WARNING:WARNING: To avoid possible electrical shock, be sure you have turned offTo avoid possible electrical shock, be sure you have turned off

the power at the main circuit panel before wiring. Follow the steps belowthe power at the main circuit panel before wiring. Follow the steps below

to connect the fan to your household wiring. Use the wire connecting nutsto connect the fan to your household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connector with electrical tape. Make suresupplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.there are no loose wire stands or connections.

WARNING:WARNING: If your house wires are different colors than referenced in thisIf your house wires are different colors than referenced in this

manual, stop immediately. A professional electrician is recommended tomanual, stop immediately. A professional electrician is recommended to

determine proper wiring.determine proper wiring.

Step 1.Step 1. Insert the receiver into the motor assembly, and keep flat in oppositionInsert the receiver into the motor assembly, and keep flat in opposition

of ceiling. (Fig. 9)of ceiling. (Fig. 9)

Step 2.Step 2. Motor to Receiver Electrical Connections: Connect the BLACKMotor to Receiver Electrical Connections: Connect the BLACK

wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver.wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver.

Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTORConnect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR

N" from the receiver. Connect the BLUE wire from the fan to the BLUE wireN" from the receiver. Connect the BLUE wire from the fan to the BLUE wire

marked "FOR LIGHT" from the receiver. Secure all the wire connections withmarked "FOR LIGHT" from the receiver. Secure all the wire connections with

the plastic wire connectors provided. (Fig. 10)the plastic wire connectors provided. (Fig. 10)

Step 3.Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect theRemote Receiver to Outlet Box Electrical Connections: Connect the

BLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" fromBLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" from

the receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITEthe receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITE

wire marked "AC IN N" from the receiver. Secure all the wire connections withwire marked "AC IN N" from the receiver. Secure all the wire connections with

the plastic wire connectors provided. (Fig. 10)the plastic wire connectors provided. (Fig. 10)

Receiver

Motor Assembly

Outlex box

White

Green or bare copper (ground)

White("AC IN N")

White("TO MOTOR N")

Ground wire

White(Neutral)

Black

Black("AC IN L")

Black ("TO MOTOR L"

Black (motor)

Blue(FOR LIGHT)

Blue(for light)

Fig. 9

Fig. 10

10 | KICHLER.COM

MAKE THE ELECTRICAL CONNECTIONS

FINISHING THE MOTOR INSTALLATION

Step 4.Step 4. If your outlet box has a ground wire (green or bare copper) connectIf your outlet box has a ground wire (green or bare copper) connect

it to the fan ground wires : otherwise connect the fan ground wire to theit to the fan ground wires : otherwise connect the fan ground wire to the

mounting bracket. Secure the wire connection with a plastic nut provided.mounting bracket. Secure the wire connection with a plastic nut provided.

After connecting the wires, spread them apart so that the green and whiteAfter connecting the wires, spread them apart so that the green and white

wires are on one side of the outlet box and black and blue wires are on thewires are on one side of the outlet box and black and blue wires are on the

other side.other side.

NOTE:NOTE: Carefully tuck the wire connections up into the outlet box.Carefully tuck the wire connections up into the outlet box.

NOTE:NOTE: Fan must be installed at a maximum distance of 30 feet from theFan must be installed at a maximum distance of 30 feet from the

transmitting unit for proper signal transmission between the transmittingtransmitting unit for proper signal transmission between the transmitting

unit and the fan’s receiving unit.unit and the fan’s receiving unit.

Step 1.Step 1. Remove the motor assembly from the hook of the ceiling mountingRemove the motor assembly from the hook of the ceiling mounting

bracket and push up the motor assembly until the two screws on the ceilingbracket and push up the motor assembly until the two screws on the ceiling

mounting bracket are engaged with the slot holes on the canopy of themounting bracket are engaged with the slot holes on the canopy of the

motor assembly. Rotate the motor assembly slightly until the two screwmotor assembly. Rotate the motor assembly slightly until the two screw

heads are in the slot holes. Install the two screws previously removed andheads are in the slot holes. Install the two screws previously removed and

tighten all four screws. (Fig. 11)tighten all four screws. (Fig. 11)

Step 2.Step 2. Push the canopy trim ring up until it locks into place at the top of thePush the canopy trim ring up until it locks into place at the top of the

canopy. (Fig. 12)canopy. (Fig. 12)

Fig. 11

Fig. 12

Canopy Trim Ring

This manual suits for next models

Table of contents

Languages:

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting 54 Meredith User manual

Kichler Lighting

Kichler Lighting Wilton User manual

Kichler Lighting

Kichler Lighting Humble 300415 User manual

Kichler Lighting

Kichler Lighting PINION 60 User manual

Kichler Lighting

Kichler Lighting Starkk 330180MWH User manual

Kichler Lighting

Kichler Lighting 52 inch Colerne LED User manual

Kichler Lighting

Kichler Lighting Decor InnesII 300130 User manual

Kichler Lighting

Kichler Lighting Windham User manual

Kichler Lighting

Kichler Lighting Pacific Edge 300157 User manual

Kichler Lighting

Kichler Lighting KAPONO User manual

Kichler Lighting

Kichler Lighting 35162 User manual

Kichler Lighting

Kichler Lighting 300370 User manual

Kichler Lighting

Kichler Lighting Renew Select Patio User manual

Kichler Lighting

Kichler Lighting Grace 300316 User manual

Kichler Lighting

Kichler Lighting VASSAR User manual

Kichler Lighting

Kichler Lighting Botella User manual

Kichler Lighting

Kichler Lighting Hatteras Bay Patio User manual

Kichler Lighting

Kichler Lighting Maeve LED 52 User manual

Kichler Lighting

Kichler Lighting Surrey Climates 60 User manual

Kichler Lighting

Kichler Lighting Deckard User manual

Kichler Lighting

Kichler Lighting Rivetta User manual

Kichler Lighting

Kichler Lighting 310155 User manual

Kichler Lighting

Kichler Lighting Seaside User manual

Kichler Lighting

Kichler Lighting Sterling Manor Patio User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual