Kichler Lighting Eris User manual
60" Eris LED
TABLE OF CONTENTS
SAFETY RULES ………………………………………………………. 4
TOOLS REQUIRED …………………………………………….… 5
PACKAGE CONTENTS ………………………………………… 5
MOUNTING OPTIONS ………………………………………… 6
HANGING THE FAN ……………………………………………... 7
INSTALLATION OF SAFETY SUPPORT ……………… 9
ELECTRIC CONNECTIONS ………………………………… 10
FINISHING THE INSTALLATION ………………………… 11
INSTALLING THE SWITCH HOUSING …………………… 12
INSTALLING WITHOUT LIGHT KIT ………………………… 13
INSTALLING THE LED LIGHT KIT AND GLASS ….… 14
INSTALLING THE WALL CONTROL ………………………… 15
CONTROL SYSTEM SET-UP …………………………………… 16
OPERATING INSTRUCTIONS …………………………………… 16
TROUBLESHOOTING ……………………………………………… 17
FCC WARNING ………………………………………………………….. 18
60" Eris LED
3
4
WARNING:
WARNING:
PACKAGE CONTENTS
Unpack your fan and check the contents . You should have the following items:
A. Mounting Plate
B. Mounting Plate Cover
C. Motor Body
D. Fan Blade (3)
E .Switch Housing
F. Steel Cap
G. LED Light Kit
H. Glass Assembly
I. Wall Control System
Phillips screwdriver
Blade screwdriver
11 mm wrench
Step ladder
Wire cutters
TOOLS REQUIRED
J. Package hardware
1) Mounting hardware :
Wood screw (2) ,Flat Washer (2) , Screw (2) ,
Lock washer (2), Wire Connector (3)
2) Blade attachment hardware :
Screws (14)
3) Safety cable hardware :
Wood screw (1) ,Spring washer (1),
Flat washer (1)
4) Balance kit
5) Light Kit hardware: screw (4)
6) Mounting plate cover hardware:
screw (4); screw with washer (4)
60" Eris LED
5
J
A
B
C
E
G
H
F
I
D
6
MOUNTING OPTIONS
If there isn’t an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the moving weight of the fan
(at least 50 lbs). Do not use plastic outlet boxes.
box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
NOTE: Fig.3 is only for fan with downrod hanging system.
clearance between the tip of the blade and the ceiling. A minimum
clearance of 12” is suggested for optimal operation.
NOTE: Depending on the location you have selected for installation,
you may need to purchase and install a “Joist Hanger” for the
support of the outlet box. Make sure the joist hanger you purchase
has been designed for use with ceiling fans. (Fig. 4)
Fig. 1
Outlet Box
Outlet Box
Fig. 2
Provide strong
support
Recessed
Outlet Box Ceiling
Mounting
Plate
Fig. 3
ANGLED CEILING
MAXIMUM 30° ANGLE
Outlet Box
Fig. 4
HANGING THE FAN
REMEMBER to turn o the power before you begin installation. This is necessary
for your safety and also the proper programming of the control system.To properly
install your ceiling fan, follow the steps below.
Step 1 . Before attaching fan to outlet box (not included), ensure the outlet box is
securely fastened to at least two points to a structural ceiling member (a loose box
will cause the fan to wobble). Pass the 120 volt supply wires from the ceiling outlet
box through the center of the ceiling mounting plate. Install mounting plate to
outlet box in ceiling using the screws and washers included with the outlet box or
screws and washers in the hardware bag. (Fig. 5)
Step 2. To install one blade to the motor assembly , align the orientation plate on
the blade with one of the three orientation plates on the motor assembly, then align
the three holes separately on the blade and the motor posts(Fig. 6a), and fix the
blade to motor posts using three(3) blade screws found in blade attachment
hardware pack (Fig.6b.)
Step 3. Proceed with installing the rest two blades in the same way, be sure the tab
on the blade already installed be inserted into the cave on the blade to be installed
in place.(Fig. 7)
Fig. 5
Fig. 6a
Fig. 6b
60" Eris LED
7
Outlet Box
Flat Washer
Mounting Plate
Screw
Fig. 7
Cave
Tab
Blade Screw
Blade Assembly
Orientation Plate
Motor Post
Blade Asembly
Orientation Plate
8
Step 4 . Carefully feed the wires up through the mounting plate cover, lightly
attach mounting plate cover over the motor and securely tighten with three (3)
screws with washer found in mounting plate cover hardware bag.(Fig. 8)
Step 6 . Hook the motor body onto the ceiling plate as shown. You can now proceed with
the electrical wiring of your fan. (Fig. 10)
HANGING THE FAN
Step 5
. Turn over the motor assembly carefully and securely tighten blade
assemblies with blade screws.(Fig. 9)
Fig. 9
Fig. 8
Fig. 10
Screw with Washer
Mounting Plate Cover
Blade Assembly
Blade Screw
Mounting Plate
Motor Assembly
Step 1.
NOTE:
INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
A safety support cable is provided to help prevent the ceiling fan from faIling, please
install it as follows.
Drive a wood screw and washers into the side of the brace that holds the outlet
box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)
Insert the safety cable through the mounting plate and one of the holes in the
outlet box into the ceiling. Adjust the length of the safety cable to reach the screw and
washers by pulling the extra cable through the cable clamp until the overall length is
correct, put the end of the cable back through the cable clamp, forming a loop at the
end of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the
safety cable over the wood screw and under the washer. Tighten the wood screw
securely. (Fig. 12)
Although the safety support cable is required for Canadian installations only.
It’s a good idea to make the attachment with any installation.
Step 2.
Fig. 11
Flat Washer
Wood Screw
Spring Washer
Outlet Box
Support Brace
Ceiling
Fig. 12
Safety Cable Bolt Wood Screw
60" Eris LED
9
10
MAKE THE ELECTRIC CONNECTIONS
WARNING: To avoid possible electrical shock, be sure you have turned o the power
at the main circuit panel before wiring. Follow the steps below to connect the fan to
your household wiring. Use the wire connecting nuts supplied with your fan. Secure
the connector with electrical tape. Make sure there are no loose wire stands or connections.
WARNING: If your house wires are dierent colors than referenced in this manual,
stop immediately. A professional electrician is recommended to determine proper wiring.
Step 1. Motor to Receiver Electrical Connections:
Connect the BLACK wire from the fan to BLACK wire marked "TO MOTOT L" from the
receiver.
Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR N" from
the receiver.
Connect the BLUE wire from the fan to the BLUE wire marked "FOR LIGHT " from the
receiver.
Secure all the wire connections with the plastic wire connectors provided. ( Fig. 13)
Step 2. Remote Receiver to Outlet Box Electrical Connections:
Connect the BLACK (hot)wire from the ceiling to the BLACK wire marked “AC IN L”
from the wall control .
Connect the WHITE (Neutral ) wire from the ceiling to the WHITE wire marked “ AC IN N”
from the receiver.
Connect the BLACK (To Motor L) wire from the wall control to the RED wire marked
“ AC IN L” from the receiver.
Secure the wire connections with the plastic wire connectors provided .(Fig. 14)
Step 3. Insert the receiver into the mounting plate cover, and keep flat in opposition of
ceiling. (Fig. 14)
Fig. 13
Fig. 14
White("AC IN N")
Ground wire
Blue(FOR LIGHT)
White (Neutral)
Blue(for light)
White("TO MOTOR N")
Black (motor)
Receiver
Black ("TO MOTOR L")
Red("AC IN L")
Black (hot)
Outlex box
White (Neutral)
Black ("AC IN L")
Black ("TO MOTOR L") Ground/Earth
Green or bare copper (ground)
Mounting Plate
Mounting Plate Cover
Receiver
Table of contents
Other Kichler Lighting Fan manuals
Kichler Lighting
Kichler Lighting Logan User manual
Kichler Lighting
Kichler Lighting Maeve LED 52 User manual
Kichler Lighting
Kichler Lighting FRYST User manual
Kichler Lighting
Kichler Lighting Lacey User manual
Kichler Lighting
Kichler Lighting Maor 310136 User manual
Kichler Lighting
Kichler Lighting Imari 65 User manual
Kichler Lighting
Kichler Lighting Jace LED User manual
Kichler Lighting
Kichler Lighting Highland Manor User manual
Kichler Lighting
Kichler Lighting Hatteras Bay Patio User manual
Kichler Lighting
Kichler Lighting Lyndon 300120 User manual
Kichler Lighting
Kichler Lighting 35166 User manual
Kichler Lighting
Kichler Lighting Canfield User manual
Kichler Lighting
Kichler Lighting Cameron 310204WH User manual
Kichler Lighting
Kichler Lighting ETL User manual
Kichler Lighting
Kichler Lighting Bentzen User manual
Kichler Lighting
Kichler Lighting 310125 User manual
Kichler Lighting
Kichler Lighting Vassar 330002OZ User manual
Kichler Lighting
Kichler Lighting KOSMUS User manual
Kichler Lighting
Kichler Lighting 35155 User manual
Kichler Lighting
Kichler Lighting Starkk User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
