Kichler Lighting 300044 User manual

Product images may vary slightly from actualproduct.

56”/ 48” Brahm LED

INSTRUCTION MANUAL

Model# 300044, 300048

READ AND SAVE THESE INSTRUCTIONS

SAFETY RULES…………………………………………………………………….....3

TOOLS REQUIRED………………………………………………………………….5

PACKAGE CONTENTS……………………………………………………………5

MOUNTING OPTIONS……………………………………………………………6

HANGING THE FAN………………………………………………………………...7

INSTALLATION OF SAFETY SUPPORT……………………………….9

ELECTRICAL CONNECTIONS……………………………………………..10

FINISHING THE MOTOR INSTALLATION……………………………...11

ATTACHING THE FAN BLADES……………………………………………...12

INSTALLING THE SWITCH HOUSING……………………………………13

INSTALLING THE LIGHT KIT AND GLASS……………………………..14

INSTALLING THE COOLTOUCH CONTROL

SYSTEM WALL PLATE……………………………………………………………..15

INSTALLING AND REMOVING THE HANDHELD

TRANSMITTER………………………………………………………………………....16

OPERATING INSTRUCTIONS…………………………………………………16

REVERSE FUNCTION………………………………………………………………18

FCC INFORMATION…………………………………………………………………18

TROUBLESHOOTING………………………………………………………………19

TABLE OF CONTENTS

2 | KICHLER.COM

SAFETY RULES

CAUTION – RISK OF SHOCK – Disconnect Power at

the main circuit breaker panel or main fusebox before

starting and during the installation.

WARNING: All wiring must be in accordance with the

National Electrical Code “ANSI/NFPA 70” and local

electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

WARNING: To reduce the risk of electric shock, this fan

must be installed with a general-use, isolating wall

control/switch.

WARNING: Not suitable for use with solid-state speed

controls.

WARNING: Chemical Burn Hazard. Keep batteries

away from children.; andThis product contains a

lithium button/coin cellbattery. If a new or used lithium

button/coin cellbattery is swallowed or enters the

body, it can causesevere internal burns and can lead to

death in as littleas 2 hours. Always completely secure

the batterycompartment. If the batterycompartment

does notclose securely, stop using the product,

remove thebatteries, and keep it away from children. If

you thinkbatteries might have been swallowed or

placed insideany part of the body, seek immediate

medical attention.

a) The cells shall be disposed of properly,

includingkeeping them away from children; and

b) Even used cells may cause injury.

WARNING: To reduce the risk of fire, electric shock, or

personal injury, mount to outlet box marked

“acceptable for fan support of 15.9 kg (35 lbs.) or less”

and use mounting screws provided with the outlet box.

Most outlet boxes commonly used for the support of

light fixtures are not acceptable for fan support and

may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is

strongly recommended.

The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

15.9 kg (35 pounds). Use only cULus Listed outlet boxes

marked“AcceptableforFan Supportof15.9kg (35lbs)orless”.

56”/ 48” Brahm LED | 3

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THEBLADE DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

The fan must be mounted with a minimum of 2.1 m (7 feet)

clearance from the trailing edge of the blades to the floor.

To operate the reverse function on this fan, press the

reverse button while the fan is running.

Avoid placing objects in the path of the blades.

WARNING: make sure the power is disconnected

before cleaning your fan.

To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

After making electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the other

side of the outlet box.

Electrical diagrams are reference only. Light kits that

are not packed with the fan must be cULus Listed and

marked suitable for use with the model fan you are

installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

All set screws must be checked, and retightened where

necessary, before installation.

The subject fan weight information is as below:

10.

11.

12.

13.

14.

15.

16.

17.

Model

300044

300048

Net Weight

(kgs)

Gross Weight

(kgs)

Net Weight

(lbs)

Gross Weight

(lbs)

9.18 10.22 20.21 22.50

7.58 8.48 16.68 18.66

4 | KICHLER.COM

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

•Phillips Screwdriver

•Blade Screwdriver

•11 mm Wrench

•Step Ladder

•Wire Cutters

Unpack your fan and check the contents. You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Fan Blade (5)

H. Switch Housing

I. Light Kit

J. Glass

K. Wall control Kit:

Receiver (1), Control (1), Metal Plate (1),

Wire connector (6), Wood Screw (2),

Battery (2), Long Screw (2),

Short Screw (2), Expansion Anchor (2),

Plastic Nut (2)

L. Package Hardware

1) Mounting Hardware:

Wire Connectors (3)

2) Blade Attachment Hardware:

Screws (15), Washers (15)

3) Safety Cable Hardware:

Wood Screw (1)

Spring Washer (1)

Flat Washer (1)

56”/ 48” Brahm LED | 5

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the full weight of

the fan (up to 15.9 kg (35 lbs.)). Do not use plastic outlet boxes.

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist

Hanger” for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 20° ANGLE

6 | KICHLER.COM

HANGING THE FAN

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 5)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain for later use.

Remove the hanger ball from the downrod assembly by loosening set screw, removing

NOTE: Make sure to keep loosened hardware separate to avoid confusion during

installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 7)

Outlet Box

Fig. 5

Fig. 6

Fig. 7

Ceiling Mounting Bracket

Flat Washer

Screw

Hanger Ball

Set Screw

Cross Pin

Hairpin

Clevis Pin

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

Set Screw

Motor Body

56”/ 48” Brahm LED | 7

HANGING THE FAN (continued)

Step 4. Carefully feed fan wires and safety cable up through the downrod.

Thread the downrod onto the motor coupling until the clevis pin holes are

aligned. Next, replace the clevis pin and hairpin, then tighten both set screws.

(Fig. 8)

Step 5. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod. Make sure the

cross pin is in the correct position and the set screw is tight and the wires are

not twisted. (Fig. 9)

Step 6. Now lift the motor body into position and place the hanger ball into

the mounting bracket. Rotate until the “Check Tab” has dropped into the

“Registration Slot” and seats firmly. (Fig. 10) The entire motor body should

not rotate if this is done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the ceiling

fan during operation.

Fig. 8

Clevis Pin

Clip

Set Screw

Clevis Pin

Motor Body

Clip

Set Screw

Fig. 9

Cross Pin Set Screw

Hanger Ball

Canopy

Canopy Hole Cover

Coupling Cover

Motor Body

Fig. 10

Mounting Bracket Hanger Ball

Registration Slot

Check Tab

8 | KICHLER.COM

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 12

Fig. 11

56”/ 48” Brahm LED | 9

MAKE THE ELECTRICAL CONNECTIONS

WARNING:

the main circuit panel before wiring.

To avoid possible electrical shock, be sure you have turned o the power at

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.

WARNING:

immediately. A professional electrician is recommended to determine proper wiring.

If your house wires are dierent colors than referenced in this manual, stop

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of

ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connections: Connect the BLACK wire from the fan

to BLACK wire marked “TO MOTOR L” from the receiver. Connect the WHITE wire from

the fan to the WHITE wire marked “TO MOTOR N” from the receiver. Connect the BLUE

wire from the fan to the BLUE wire marked “FOR LIGHT “ from the receiver. Secure all

the wire connections with the plastic wire connectors provided. (Fig. 14)

Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect the BLACK (hot)

wire from the ceiling to the BLACK wire marked “AC IN L” from the receiver. Connect

the WHITE (Neutral) wire from the ceiling to the WHITE wire marked “AC IN N” from the

receiver. Secure all the wire connections with the plastic wire connectors provided.

(Fig. 14)

Mounting

Bracket

Fig. 14

Receiver

Fig. 13

Outlet box

Black White

Green or bare

copper (ground)

Black (“AC IN L”)

Receiver

Black (“TO MOTOR L”)

Black (motor)

Blue (FOR LIGHT)

White (“AC IN N”)

White (“TO MOTOR N”)

Ground wire

White (Neutral)

10 | KICHLER.COM

This manual suits for next models

Table of contents

Languages:

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting Sunburst 300170 User manual

Kichler Lighting

Kichler Lighting 310125 User manual

Kichler Lighting

Kichler Lighting Chicago User manual

Kichler Lighting

Kichler Lighting Maor 310136 User manual

Kichler Lighting

Kichler Lighting Cottage Grove User manual

Kichler Lighting

Kichler Lighting Cortez User manual

Kichler Lighting

Kichler Lighting Fit User manual

Kichler Lighting

Kichler Lighting 310155 User manual

Kichler Lighting

Kichler Lighting Makoda User manual

Kichler Lighting

Kichler Lighting Terra Select User manual

Kichler Lighting

Kichler Lighting FRYST User manual

Kichler Lighting

Kichler Lighting 52" RENEW ENERGY STAR User manual

Kichler Lighting

Kichler Lighting sterling manor select User manual

Kichler Lighting

Kichler Lighting 380106 User manual

Kichler Lighting

Kichler Lighting FERRON User manual

Kichler Lighting

Kichler Lighting Harbour Walk Patio User manual

Kichler Lighting

Kichler Lighting IMARI 300365SBK User manual

Kichler Lighting

Kichler Lighting Kevlar 310150WCP User manual

Kichler Lighting

Kichler Lighting Canfield Patio 310192 User manual

Kichler Lighting

Kichler Lighting Selectlight fixture User manual

Kichler Lighting

Kichler Lighting Decor Link User manual

Kichler Lighting

Kichler Lighting Monarch II Patio User manual

Kichler Lighting

Kichler Lighting Deckard User manual

Kichler Lighting

Kichler Lighting Decor Dorset User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual