Juniper MX240 User manual

Removing Components from the MX240 Chassis Before Installing It Without a Lift

To make the router light enough to install manually, you first remove most

components from the chassis. The procedures in this section for removing

components from the chassis are for initial installation only, and assume that you

have not connected power cables to the router. The following procedures describe

how to remove components from the chassis, first from the rear and then from the

front:

1. Removing the Power Supplies Before Installing the MX240 Router Without a

Lift on page 1

2. Removing the Fan Tray Before Installing the MX240 Router Without a

Lift on page 2

3. Removing the SCBs Before Installing the MX240 Router Without a Lift on page 2

4. Removing the DPCs Before Installing the MX240 Router Without a Lift on page 3

5. Removing the FPC Before Installing the MX240 Router Without a Lift on page 4

Removing the Power Supplies Before Installing the MX240 Router Without a Lift

Remove the leftmost power supply first and then work your way to the right. To

remove the AC or DC power supplies (see Figure 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to an approved site ESD grounding point. See the instructions

for your site.

2. For an AC-powered router, switch the AC input switch on the power supply to

the off (O) position. For a DC-powered router, switch the DC circuit breaker on

the power supply to the off (O) position.

We recommend this even though the power supplies are not connected to power

sources.

3. Pull the power supply straight out of the chassis.

Figure 1: Removing a Power Supply Before Installing the Router

Removing Components from the MX240 Chassis Before Installing It Without a Lift ■1

Removing the Fan Tray Before Installing the MX240 Router Without a Lift

To remove the fan tray (see Figure 2 ):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to an approved site ESD grounding point. See the instructions

for your site.

2. Loosen the captive screws on the fan tray faceplate.

3. Grasp the fan tray handle, and pull it out approximately 1 to 3 inches.

4. Press the latch located on the inside of the fan tray to release it from the chassis.

5. Place one hand under the fan tray to support it, and pull the fan tray completely

out of the chassis.

Figure 2: Removing the Fan Tray

Removing the SCBs Before Installing the MX240 Router Without a Lift

To remove the SCBs (see Figure 3):

1. Place an electrostatic bag or antistatic mat on a flat, stable surface.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to an approved site ESD grounding point. See the instructions

for your site.

3. Rotate the ejector handles simultaneously counterclockwise to unseat the SCB.

4. Grasp the ejector handles, and slide the SCB about halfway out of the chassis.

5. Place one hand underneath the SCB to support it, and slide it completely out of

the chassis. Place it on the antistatic mat.

2■Removing the Fan Tray Before Installing the MX240 Router Without a Lift

CAUTION: Do not stack hardware components on one another after you remove

them. Place each component on an antistatic mat resting on a stable, flat surface.

6. Repeat the procedure for the second SCB.

Figure 3: Removing an SCB

Removing the DPCs Before Installing the MX240 Router Without a Lift

To remove a DPC (see Figure 4):

1. Have ready an antistatic mat for the DPC. Also have ready rubber safety caps

for each DPC using an optical interface on the DPC that you are removing.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to an approved site ESD grounding point. See the instructions

for your site.

3. Simultaneously turn both the ejector handles counterclockwise to unseat the

DPC.

4. Grasp the handles, and slide the DPC straight out of the card cage halfway.

5. Place one hand around the front of the DPC and the other hand under it to

support it. Slide the DPC completely out of the chassis, and place it on the

antistatic mat or in the electrostatic bag.

CAUTION: The weight of the DPC is concentrated in the back end. Be prepared to

accept the full weight—up to 13.1 lb (5.9 kg)—as you slide the DPC out of the chassis.

When the DPC is out of the chassis, do not hold it by the ejector handles, bus bars,

or edge connectors. They cannot support its weight.

Do not stack DPC on top of one another after removal. Place each one individually

in an electrostatic bag or on its own antistatic mat on a flat, stable surface.

Removing the DPCs Before Installing the MX240 Router Without a Lift ■3

Figure 4: Removing a DPC

Removing the FPC Before Installing the MX240 Router Without a Lift

To remove an FPC (see Figure 5):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to an approved site ESD grounding point. See the instructions

for your site.

2. Simultaneously turn both the ejector handles counterclockwise to unseat the

FPC.

3. Grasp the handles and slide the FPC straight out of the card cage halfway.

4. Place one hand around the front of the FPC and the other hand under it to support

it. Slide the FPC completely out of the chassis, and place it on the antistatic mat

or in the electrostatic bag.

CAUTION: The weight of the FPC is concentrated in the back end. Be prepared to

accept the full weight—up to 18 lb (8.2 kg)—as you slide the FPC out of the chassis.

When the FPC is out of the chassis, do not hold it by the ejector handles, bus bars,

or edge connectors. They cannot support its weight.

4■Removing the FPC Before Installing the MX240 Router Without a Lift

Figure 5: Removing an FPC

Related Topics ■Tools and Parts Required to Remove Components from an M Series, MX Series,

or T Series Router

■Installing the MX240 Chassis in the Rack Manually

■Reinstalling Components in the MX240 Router After Installing It Without a Lift

■Preventing Electrostatic Discharge Damage to an M Series, MX Series, or T Series

Routing Platform

Published: 2010-01-22

Removing the FPC Before Installing the MX240 Router Without a Lift ■5

Other manuals for MX240

Table of contents

Other Juniper Network Hardware manuals

Juniper

Juniper IDP 800 User manual

Juniper

Juniper MX10004 Installation instructions

Juniper

Juniper T1600 User manual

Juniper

Juniper Junos Space JA2500 Installation instructions

Juniper

Juniper Junos Space JA1500 User manual

Juniper

Juniper Day One Plus SRX380 User manual

Juniper

Juniper MX480 Installation instructions

Juniper

Juniper SRX300 Series User manual

Juniper

Juniper JRR200 Installation instructions

Juniper

Juniper ACX7100 User manual

Juniper

Juniper JSA3800 Installation instructions

Juniper

Juniper SSR1300 User manual

Juniper

Juniper Junos Space JA1500 User manual

Juniper

Juniper JRR200 User manual

Juniper

Juniper NetScreen-5GT Wireless User manual

Juniper

Juniper MX104 User manual

Juniper

Juniper MX SERIES - FAN TRAY UPGRADE REV1 4-2010 User manual

Juniper

Juniper JSA1500-BSE User manual

Juniper

Juniper JSA7800 User manual

Juniper

Juniper DUAL-PORT T1-E1 GPIMS User manual

Juniper

Juniper PTX3000 User manual

Juniper

Juniper Day One+ QFX5700 User manual

Juniper

Juniper SRX3400 User manual

Juniper

Juniper SRX5400 Service manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide